Instrukcja obsługi Peerless Industries Peerless Video Wall Mounting Solution DS-VW660

Streszczenie treści zawartej na stronie nr. 1

Installation and Assembly:
Video Wall Mount
Model: DS-VW660
Maximum Load Capacity: 200 Ib ( 90 kg)
ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10
1 of 10

Streszczenie treści zawartej na stronie nr. 2

NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor. • This product should only be installed

Streszczenie treści zawartej na stronie nr. 3

Vertical Spacing Location If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine vertical spacing. 1 T o determine lower mounting slot position of second mount, add display height to (Y1 ) or (Y2 ) DISPLAY HEIGHT H 10.25 1.688 X Y2 Y1 .938 Vertical Location X - 10.25 + (.938 OR 1.688) = (Y1 OR Y2) Horizontal Spacing Location If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine horizontal spacing.

Streszczenie treści zawartej na stronie nr. 4

PARTS LIST Description Qty. Part # A carriage assembly 1 145-1160 B wall plate 1 145-1145 C adapter bracket 2 145-1158 D lock bracket 1 145-1154 E #14 x 2.5 hex head wood screw 4 5S1-015-C03 F concrete anchor 4 590-0320 G .38 OD x .06 LG nylon shoulder washer 4 590-2233 H M5 x 10 mm socket pin serrated washer head screw 2 510-1126 I M6 x 12 mm phillips screw 4 520-1128 J M8 x 16 mm phillips screw 4 520-9257 K M5 x 6 mm phillips screw 3 520-1023 L 4 mm allen wrench 1 560-9646 A B C D E F G

Streszczenie treści zawartej na stronie nr. 5

Installation to Wall Stud WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • T ighten wood screws so that wall plate is firmly attac hed, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud. The use of an "edge

Streszczenie treści zawartej na stronie nr. 6

Installation to Solid Concrete or Cinder Block WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used

Streszczenie treści zawartej na stronie nr. 7

Attaching Adapter Brackets to Display Attach adapter brackets (C ) to back of display using four M6 x 12 mm phillips screws (I ) with nylon shoulder washer (G ), or four 2 M8 x 15 mm phillips screws (J ) as shown below . NOTE: Hardware to attach dedicated plates to the mount are included with the dedicated plates. I or J G C Attach adapter brackets (C ) and display onto channels on carriage assembly (A ) as shown in figure 3.1. 3 Secure adapter brackets (C ) using lock bracket (D ) with thr

Streszczenie treści zawartej na stronie nr. 8

Horizontal Display Position OPTIONAL GUIDE: When positioning adapter brackets (C ) make sure outside edge of adapter bracket is in notch on display carriage as shown in detail 1. C Installing Carriage Assembly to Wall Plate Hook Carriage Assembly (A ) slot onto pins on wall plate (B ). Make sure that pins fully engage slot of carriage assembly (A ) as 4 shown in detail 2. A B ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10 8 of 10 Screen and adapter brackets can slide along rail to positio

Streszczenie treści zawartej na stronie nr. 9

Secure Carriage Assembly (A ) to wall plate (B ) with two M5 x 10 mm socket pin serrated washer head screws (H ) using 5 4 mm allen wrench (L ) as shown below . B H A Horizontal Display Adjustment 6 Adapter Brackets (C ) and display can be adjusted horizontally . ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10 9 of 10

Streszczenie treści zawartej na stronie nr. 10

Carriage Assembly Adjustment Use legend below to determine position of display. 7 NOTE: Each knob can be adjusted independently for fine tuning adjustments. Turn knob CLOCKWISE to tighten Turn knob COUNTER-CLOCKWISE to loosen UP DOWN ROLL RIGHT ROLL LEFT ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10 10 of 10 © 2010, Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners.