Streszczenie treści zawartej na stronie nr. 1
3-865-150-12 (1)
Video Cassette
Recorder
Operating Instructions
PAL NTSC 4.43
SLV-SE70EN/EG
SLV-SX70EN
SLV-SE50EG
©1999 by Sony Corporation
Streszczenie treści zawartej na stronie nr. 2
Caution WARNING Television programmes, films, video tapes and To prevent fire or shock hazard, do not expose other materials may be copyrighted. the unit to rain or moisture. Unauthorized recording of such material may To avoid electrical shock, do not open the be contrary to the provisions of the copyright cabinet. Refer servicing to qualified a laws. Also, use of this recorder with cable personnel only. television transmission may require authorization from the cable television Mains lead mu
Streszczenie treści zawartej na stronie nr. 3
Getting Started Table of contents Getting Started 4 Step 1: Unpacking 5 Step 2: Setting up the remote commander 9 Step 3: Connecting the VCR 14 Step 4: Tuning your TV to the VCR 16 Step 5: Setting up the VCR with the Auto Set Up function 18 Step 6: Setting the clock 23 Selecting a language 24 Presetting channels 28 Changing/disabling programme positions 34 Setting the Canal Plus decoder 68 Searching using the index Basic Operations function 39 Playing a tape 69 Adjusting the picture 43 Recording
Streszczenie treści zawartej na stronie nr. 4
Getting Started Step 1 Unpacking Check that you have received the following items with the VCR: • Remote commander • Aerial cable • R6 (size AA) batteries Checking your model name The instructions in this manual are for the 4 models: SLV-SE70EN, SE70EG, SX70EN, and SE50EG. Check your model number by looking at the rear panel of your VCR. The SLV-SE70EN is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-SE50EG only.” 4
Streszczenie treści zawartej na stronie nr. 5
Getting Started Step 2 Setting up the remote commander Inserting the batteries Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position. Using the remote commander Remote sensor You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your
Streszczenie treści zawartej na stronie nr. 6
Step 2 : Setting up the remote commander (continued) I/u WIDE V AUDIO MONITOR ; FASTEXT buttons DISPLAY É TV/VIDEO 123 456 Programme number buttons 789 ? 0 PROG+/–/ Ã/× ç +/– TV control buttons To Press Turn the TV into standby mode I/u Select an input source of the TV either from É TV/VIDEO aerial in or from line in Select the programme position of the TV Programme number buttons, ?, PROG +/– 6 Getting Started
Streszczenie treści zawartej na stronie nr. 7
Getting Started To Press Adjust the volume of the TV ç +/– Switch to TV (Teletext off) ; (TV) Switch to Teletext V (Teletext) Select the sound AUDIO MONITOR Use FASTEXT FASTEXT buttons Call up on-screen display DISPLAY Change the Teletext page Ã/× Switch to/from wide mode of a Sony wide TV (For WIDE other manufacture’s wide TV, see “Controlling other TVs with the remote commander” below.) Notes • With normal use, the batteries should last about three to six months. • If you do not use the remote
Streszczenie treści zawartej na stronie nr. 8
Step 2 : Setting up the remote commander (continued) Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. To make wide mode settings, see the footnotes below this table for the applicable code numbers. Manufacturer Code number Manufacturer Code number 1 1 17* , 49 Sony 01* , 02 Panasonic 1 1 1 Akai 68 Philips 06* , 07* , 08* 12, 13 Ferguson 52 Saba 1 1 Grundig 10* , 11* Samsung 22, 23 25 Hitachi 2
Streszczenie treści zawartej na stronie nr. 9
Getting Started Step 3 Connecting the VCR If your TV has a EURO-AV connector, see page 10. If your TV does not have a EURO-AV (Scart) connector AERIAL IN AERIAL OUT Mains lead AERIAL IN to mains Aerial cable (supplied) : Signal flow 1 Disconnect the aerial cable from your TV AERIAL and connect it to AERIAL IN on the rear ANTENNE IN ENTREE panel of the VCR. OUT SORTIE AERIAL ANTENNE 2 Connect AERIAL OUT of the VCR and IN ENTREE the aerial input of your TV using the supplied aerial cable. OUT SORT
Streszczenie treści zawartej na stronie nr. 10
Step 3 : Connecting the VCR (continued) If your TV has a EURO-AV (Scart) connector AERIAL IN : LINE-1 AERIAL OUT (TV) Mains lead AERIAL IN to mains Aerial cable (supplied) EURO-AV (Scart) : Signal flow EURO-AV cable (not supplied) 1 Disconnect the aerial cable from your AERIAL ANTENNE TV and connect it to AERIAL IN on the IN ENTREE rear panel of the VCR. OUT SORTIE AERIAL ANTENNE 2 Connect AERIAL OUT of the VCR and IN ENTREE the aerial input of your TV using the supplied aerial cable. OUT SORTIE
Streszczenie treści zawartej na stronie nr. 11
Getting Started 3 Connect LINE-1 (TV) on the VCR and the EURO-AV (Scart) connector on the TV with the optional EURO-AV cable. This connection improves picture and sound quality. Whenever you want to watch the VCR picture, press É TV/ VIDEO to display the VIDEO indicator in the display window. 4 Connect the mains lead to the mains. Note • If the TV is connected to the LINE-1 (TV) connector, setting the RF MODULATOR in the OPTIONS-2 menu to OFF is recommended. In the OFF position, only the signa
Streszczenie treści zawartej na stronie nr. 12
Step 3 : Connecting the VCR (continued) About the SMARTLINK features If the connected TV complies with SMARTLINK, SMARTLINK *1 *2 *3 MEGALOGIC , EASYLINK , Q-Link , or EURO *4 VIEW LINK , you can use the SMARTLINK function after you complete the steps on the previous page (the SMARTLINK indicator appears in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features. • Preset Download You can download your TV tuner preset data to this VCR and tune the VCR ac
Streszczenie treści zawartej na stronie nr. 13
Getting Started Additional connections To a stereo system (SLV-SE70EN/ SE70EG/SX70EN only) You can improve sound quality by AUDIO OUT connecting a stereo system to the LINE IN R/L AUDIO OUT R/L jacks as shown on the right. Audio cable (not supplied) : Signal flow To a satellite tuner You can watch programmes from the satellite tuner connected to this VCR on DECODER/ the TV even when the VCR is turned off É LINE-3 IN LINE OUT using the Line Through function. When you turn on the satellite tuner,
Streszczenie treści zawartej na stronie nr. 14
Step 4 Tuning your TV to the VCR If you have connected the VCR to your TV using the EURO-AV cable, skip this step. I/u ON/STANDBY PROGRAM +/– RF CHANNEL ON/STANDBY 1 Press I/u ON/STANDBY to turn on the VCR. 2 Press RF CHANNEL on the VCR lightly. The factory-preset RF channel appears in the display window. RF CHANNEL The VCR signal is output through this channel to the TV. 3 Turn on your TV and select a programme position for the VCR picture. This programme position will now be referred to as the
Streszczenie treści zawartej na stronie nr. 15
Getting Started PROGRAM 5 Press PROGRAM +/– (repeatedly) to select the appropriate TV system for your area. Select “G” for the B/G TV system, or “K” for the D/K TV system. 6 Tune the TV to the same channel as that SONY VIDEO CASSETTE RECORDER shown in the display window so that the picture on the right appears clearly on the TV screen. Refer to your TV manual for tuning instructions. If you select the wrong TV system in step 5, the picture on the right may not appear. Select the appropriate TV
Streszczenie treści zawartej na stronie nr. 16
Step 5 Setting up the VCR with the Auto Set Up function Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the language for the on-screen display, TV channels, guide channels for the ShowView system. AUTO SET UP PROGRAM +/– AUTO 1 Hold down AUTO SET UP on the VCR for more than three seconds. SET UP The VCR automatically turns on, and the country abbreviation appears in the display window. PROGRAM 2 Press PROGRAM +/– to select
Streszczenie treści zawartej na stronie nr. 17
Getting Started 3 AUTO Press AUTO SET UP lightly. SET UP The VCR starts searching for all of the receivable channels and presets them according to the TV system you selected in “Tuning your TV to the VCR.” If you use the SMARTLINK connection, the Preset Download function starts and the SMARTLINK indicator flashes in the display window during download. After the search or download is complete, the current time appears in the display window for any stations that transmit a time signal. To cancel t
Streszczenie treści zawartej na stronie nr. 18
Step 6 Setting the clock You must set the time and date on the MENU VCR to use the timer recording features properly. The Auto Clock Set function works only if a station in your area is broadcasting a >/./?// time signal. If the Auto Set Up function OK did not set the clock correctly for your local area, try another station for the Auto Clock Set function. Setting the clock manually Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. MENU SETTINGS 1 Press MENU, th
Streszczenie treści zawartej na stronie nr. 19
Getting Started CLOCK 3 Press >/. to highlight MANUAL PLAY ADJUST, then press OK. AUTO ADJUST OFF CLOCK PROG MANUAL ADJUST OK 1 . 1 . 1999 FRI 0 : 00 SELECT : SET : CONFIRM : OK EXIT : MENU CLOCK 4 Press >/. to set the date. PLAY AUTO ADJUST OFF CLOCK PROG MANUAL ADJUST OK 28 . 1 . 1999 TUE 0 : 00 SELECT : SET : CONFIRM : OK EXIT : MENU CLOCK 5 Press / to highlight the month and set PLAY the month pressing >/.. AUTO ADJUST OFF CLOCK PROG MANUAL ADJUST OK 28 . 9 . 1999 TUE 0 : 00 SELECT : SET : C
Streszczenie treści zawartej na stronie nr. 20
Step 6 : Setting the clock (continued) CLOCK 7 Press OK to start the clock. AUTO ADJUST OFF PLAY CLOCK PROG MANUAL ADJUST 21 8 . 9 . 1999 TUE 8 : 00 OK SELECT : SET : OK EXIT : MENU MENU 8 Press MENU to exit the menu. Tips • To change the digits during setting, press ? to return to the item to be changed, and select the digits pressing >/.. • If you want to return to the previous menu, highlight RETURN and press OK. Note • The menu disappears automatically if you don’t proceed for more than a fe
