Instrukcja obsługi Metra Electronics 95-8154

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 95-8154
APPLICATIONS
LEXUS GS SERIES
1993-1997
95-8154
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double Din Radio Housing • B) Double DIN Brackets
A
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION

Streszczenie treści zawartej na stronie nr. 2

95-8154 TABLE OF CONTENTS Dash Disassembly - Lexus GS Series 1993-1997 . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Kit Assembly - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 *Note: Refer also to the instructions included with the aftermarket

Streszczenie treści zawartej na stronie nr. 3

95-8154 DASH DISASSEMBLY LEXUS GS SERIES 1993-1997 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Using a panel removal tool gently pry out on the top of the a/c vent assem- bly (including clock) and remove. (Figure A) 3 Unclip and remove ashtray assembly. Tip: Open ashtray door and pull from inside. (Figure B) B 4 Remove (4) screws securing factory radio/climate control assembly. Unplug and remove the assembly. (Figure C) 5 Remove (4) screws securing f

Streszczenie treści zawartej na stronie nr. 4

95-8154 KIT ASSEMBLY LEXUS GS SERIES 1993-1997 DOUBLE DIN RADIO STACKED ISO MOUNT UNITS PROVISON Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN Brackets onto the Double DIN Radio Housing. (Figure A) 2 Slide the factory climate controls into the Bracket/Radio Housing assembly aligning the top of the assembly with alignment pins in the bottom of the climate controls and secure using the factory hardware. (Figure B) 3 Slide the Double DIN or st

Streszczenie treści zawartej na stronie nr. 5

95-8154 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Streszczenie treści zawartej na stronie nr. 6

95-8154 NOTES 4

Streszczenie treści zawartej na stronie nr. 7

95-8154 NOTES 5

Streszczenie treści zawartej na stronie nr. 8

95-8154 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 10/25/07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST95-8154