Instrukcja obsługi Everpure CGHE1

Streszczenie treści zawartej na stronie nr. 1

CGHE1 Installation
& Operating Guide
Components
®
When you purchase the Everpure Commerical
Grade Instant Hot Water tank, contents include:
quick-connect tank mounting
fitting bracket
quick-connect fitting
tank
with filter and cap
Materials required (not provided)
1
/4" (6.4 mm)
O.D. copper
2 mounting bracket screws
tubing.
(and 2 plastic anchors if
attaching to drywall)
Shut-Off valve
with “T” fitting
(EV312120)
(Connections must meet all local codes and ordinances.)
Tools and Safety Equipm

Streszczenie treści zawartej na stronie nr. 2

IMPORTANT SAFETY INSTRUCTIONS PLEASE READ ALL INSTRUCTIONS VERY CAREFULLY When using electrical appliances, basic safety precautions should always be followed including the following: 1. Read all instructions. 2. To protect against electrical shock, do not place cord, plugs, or appliance in water or other liquid. 3. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions. Return appliance to the factory for examination, repair or adjustment. See Warranty ins

Streszczenie treści zawartej na stronie nr. 3

HOT WATER CONCEPT Unlike a household water heater, this dispenser tank is not pressurized for safety reasons. For a conventional household water heater, the faucet valve is placed after the heater tank resulting in a pressurized tank. For a hot water dispenser, the faucet valve is placed before the tank, creating an “open vent” style faucet and consequently no pressure is built up inside the tank. OVERVIEW 1. Make sure you have all necessary parts, tools and materials as suggested on manual cove

Streszczenie treści zawartej na stronie nr. 4

INSTALLATION Before You Begin Determine where you will install your hot water dispenser. The faucet can be mounted in an existing hole 1 3 in the sink (spray hose, etc.), or drill a 1 /16” (27 mm) to 1 /8” (35 mm) hole in your sink. If you want to use the spray unit or do not have a hole in your sink you will have to drill a new hole. 1 3 Stainless Steel: You need a 1 /16” (27 mm) to 1 /8” (35 mm) knockout punch available at most hardware stores or drill a hole with an expandable drill. Porcela

Streszczenie treści zawartej na stronie nr. 5

quick-connect fitting with filter and cap connects to cold water line and contains a filter inside fitting. It also has faucet line connects to a cap at one end. the inlet tube located on top corner of tank with cap quick-connect fitting filter faucet line connects to (supplied with tank). filtered cold water supply. quick-connect clamp hose connects with clamp to faucet supply center inlet tube tube at center of tank. Step 4 - Connect Cold Water Supply Check Filter in Quick-Connect Fitting The

Streszczenie treści zawartej na stronie nr. 6

Step 5 - Check for Leaks Open valve in water line. Turn faucet on (hold if necessary) to fill tank (about 1 minute). When tank is full, water will flow from faucet. Turn faucet off. Check for leaks. Step 6 - Prepare for Power Double check thermostat control dial is in the OFF position. Thermostat control dial controls the water temperature, not the water flow or delivery. IMPORTANT INFORMATION - This dispenser is equipped with a Self Re-setting Thermal Fuse Turn thermostat to OFF position and f

Streszczenie treści zawartej na stronie nr. 7

CLEANING AND MAINTENANCE Seasonal Shutdown To prevent damage when dispenser is exposed to freezing temperatures, water must be drained. 1. Unplug dispenser tank to power supply. 2. Turn thermostat control dial to OFF position (fully O-ring counterclockwise). screw 3. Turn faucet on and run water until water is cold. 4. Place a 3-quart (2.8 L) container under drain plug at bottom of the tank. Use a screwdriver to remove the screw and O-ring in the drain tube opening. When tank is fully drained

Streszczenie treści zawartej na stronie nr. 8

TROUBLESHOOTING The following situations are not covered by the One Year Replacement Warranty. 1. Water is not hot: (assuming cold water supply is connected properly and valve is open) • Check if dispenser is plugged in. • Turn thermostat control dial fully clockwise. This may produce boiling water in approximately 15 minutes and possibly be accompanied by a gurgling sound in the tank and/or water “sputtering” from the faucet. If the water boils, turn thermostat control dial slightly counterclo