Streszczenie treści zawartej na stronie nr. 1
110 Series – 220V 60Hz/230V 50Hz
Ice and Water Dispensers
Order parts online
Installation, Operation and Service Manual
www.follettice.com
C/E110CT400A/W
C/E110CR400A/W C/E110FB400A/W
Following installation, please forward this manual
to the appropriate operations person.
801 Church Lane • Easton, PA 18040, USA
(610) 252-7301 • Fax (610) 250-0696 • www.follettice.com 00109520R03
Streszczenie treści zawartej na stronie nr. 2
Table of contents Before you begin 3 Specifications 4 Field wiring 5 Installation 6 Installing freestanding dispensers 6 Installing countertop dispensers 8 ™ Installing Satellite-fill icemakers 10 Installing top mount icemakers 10 User information 12 Cleaning and sanitizing procedures 12 Service Information 14 Wiring diagram – lever models 14 ™ Wiring diagram – SensorSAFE models 15 Dispenser troubleshooting 16 Troubleshooting SensorSAFE board and sensors 17 Disassembly and replacement i
Streszczenie treści zawartej na stronie nr. 3
Welcome to Follett Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale support. To ensure that this equipment delivers that same degree of service, we ask that you review the installation portion of this manual before beginning to install the unit. Our installation instructions are designed to help you achieve a trouble-free installation. Should you have any questions or require technical help at any time, please
Streszczenie treści zawartej na stronie nr. 4
Specifications Electrical 1. Models with Satellite-fill icemakers (C/E110CR400A/W) Icemaker Dispenser 220V/60Hz/1 phase 5 amps 1.5 amps 230V/50Hz/1 phase 5 amps 1.5 amps 2. Freestanding models and models with integral icemakers (C/E110FB400A/W, C/E110CT400A/W) Total system 220V/60Hz/1 phase 6.5 amps 230V/50Hz/1 phase 6.5 amps 3. Dispensers and Satellite-fill icemakers are supplied with 7-foot power cord Ambient Air temp 38°C/100° F max. 10°C/50°F min. (best perform
Streszczenie treści zawartej na stronie nr. 5
Field wiring for countertop dispensers with Satellite-fill icemakers Model Electrical connection Current C110FB400A/W cord provided 220V 60Hz, 6.5 amp E110FB400A/W 230V 50Hz, 6.5 amp C110CT400A/W cord provided 220V 60Hz, 6.5 amp E110CT400A/W 230V 50Hz, 6.5 amp C110CR400A/W cord provided 220V 60Hz E110CR400A/W 230V 50Hz dispenser: 1.5 amp icemaker: 5.0 amp 5
Streszczenie treści zawartej na stronie nr. 6
Installation procedures Before you begin • All dispensers must be installed level in both directions to ensure proper operation • Required ventilation and recommended service clearances: • Countertop models with Satellite-fill icemaker (C/E110CR400A/W) — none. 305mm (12") at top recommended for service. • Countertop models with integral icemaker (C/E110CT400A/W) — 153mm (6") at top. 153mm (6") each side recommended for service. • Freestanding models (C/E110FB400A/W) — 102mm (4") at rear.
Streszczenie treści zawartej na stronie nr. 7
Fig. 1 – Rear connections, freestanding models access panel (B) 3/4” FPT drain (A) 3/8" FPT water inlet (A) 800mm (D) 3/8" FPT (31.5") condenser inlet location (water- (C) 3/4" MPT cooled only) icemaker drain water inlet location (water- cooled only) (E) 3/8" FPT condenser drain location (water- cooled only) 800mm (31.5") (C) 3/4" MPT 260mm icemaker drain (10.25") location (air- cooled only) 12. Verify that water sensor tabs are immersed in water in reservoir. 13. Remove top front cov
Streszczenie treści zawartej na stronie nr. 8
Installing countertop dispensers Dispensers with top mount icemakers cannot be mounted on legs. They must be bolted to counter. ! Use gloves when lifting icemaker to protect hands from sheet metal edges. 1. Position dispenser in desired location, mark Fig. 2 – Counter cut-out, all models dispenser outline on counter and remove dispenser. 2. Drill four 5mm (3/8") holes in counter (Fig. 2) to 227mm x 356mm (9" X 14") anchor dispenser to counter. 622mm (24.5") 311mm Follett countertop disp
Streszczenie treści zawartej na stronie nr. 9
10. Apply a thick bead, approximately. 6mm (1/4") Fig. 4 – Rear connections, countertop models with diameter, of NSF listed silicone sealant (Dow- integral icemakers Corning RTV-732 or equivalent) 6mm (1/4") inside marked outline of dispenser. (M) 3/8" FPT icemaker water inlet 11. Carefully position dispenser on counter. (R) 3/8" FPT condenser inlet 12. Remove four screws securing splash panel to front (water-cooled only) of dispenser and gently lay splash panel on counter. (Water line
Streszczenie treści zawartej na stronie nr. 10
Installing Satellite-fill icemakers Models C/E110CR400A/W See Icemaker Installation Manual (form #00124453) for critical installation instructions for Satellite- fill icemakers. Failure to comply with these instructions will result in poor performance and void ! warranty. 1. Install Satellite-fill icemaker following instructions in icemaker manual. 2. Run uninsulated ice transport tube from dispenser through ice transport tube knock-out, (Fig. 5G) or through counter opening to ic
Streszczenie treści zawartej na stronie nr. 11
1. Remove dispenser top front cover by removing two screws at bottom corners of cover, lifting cover slightly and pulling forward. 2. Remove icemaker compartment top and side panels. 3. Remove icemaker hold-down bracket from front of icemaker compartment. 4. Lift icemaker onto dispenser top and slide icemaker completely into position, compressor end first. Front of icemaker base must be flush with front of dispenser. 5. Reinstall hold down bracket on front of icemaker with power cord and
Streszczenie treści zawartej na stronie nr. 12
User information How the dispenser works Follett’s 110 series automatic load ice and water dispensers receive ice from Follett’s 181kg (400 lb)/day icemaker located in the dispenser base, in the cabinet top or in a remote location up to 6m (20 ft) away. Ice produced is stored in the bin section of the dispenser. When dispensing is activated, the wheel motor is energized, causing the wheel to turn. This moves ice to the dispense chute where it drops by gravity into the container held below the
Streszczenie treści zawartej na stronie nr. 13
Recommended weekly cleaning 1. Wash drain pan and grille with Solution A above. Rinse thoroughly. 2. Slowly pour solution of one cup (237ml/8 oz) household bleach mixed with 3.8L (1 gallon) hot water into drain pan to help prevent algae growth in drain lines. If dispenser is a SensorSAFE unit: 3. Deactivate dispenser by depressing and releasing clean switch located on left side of unit under top front cover. 4. Clean lens using soft cloth and mild, non-abrasive cleaner. 5. Reactivate di
Streszczenie treści zawartej na stronie nr. 14
Service information Wiring diagrams How unit works — lever models The dispense wheel motor and dispense solenoid are energized through the power and ice dispense switches. The water solenoid valve is energized through the power and water dispense switches. The icemaker receives the bin signal through the power switch, the normally closed bin thermostat and the icemaker switch. When the bin level thermostat is calling for ice, a 115V bin signal is applied to the bin signal terminals on the ice
Streszczenie treści zawartej na stronie nr. 15
How unit works — SensorSAFE models SensorSAFE models provide “touchless” ice and water dispensing. When a container is placed within the actuation zone below the ice or water chute on SensorSAFE dispenser models, an infra-red signal reflects off the container and is detected by the sensor. The sensor then sends a signal to the control board to activate the appropriate components to dispense ice or water. LEDs on the board indicate when the board is receiving a signal from the sensors. A safe
Streszczenie treści zawartej na stronie nr. 16
Dispenser troubleshooting Disconnect power to dispenser and icemaker before putting hands or arms in storage area, or attempting any repair or service to equipment. ! Before calling for service: • Check that there is ice in dispenser bin area • Check that all switches and circuit breakers are on • Check that congealed cubes are not causing a jam • Check that all drains are clear Symptom Possible cause Solution 1. Does not dispense a. Faulty dispense gate a. Replace dispense gate ice b. Faulty
Streszczenie treści zawartej na stronie nr. 17
Troubleshooting SensorSAFE board and sensors Board guide LEDs, when illuminated, indicate the following: Terminals: PWR (board power) L1 (incoming power, hot) CLN (cleaning, no dispensing cycle) L2 (neutral terminals) ICE (ice dispensing activated) WTR (power terminal for water solenoid) WTR (water dispensing activated) SOL (power terminal for dispense gate solenoid) not used WM (power terminal for wheel motor) CLN (terminals for clean cycle switch) Problem: Does not dispen
Streszczenie treści zawartej na stronie nr. 18
Lens/sensor troubleshooting 1. Turn dispenser power switch off. 2. Remove splash panel. 3. Disconnect wires from output terminal(s) (WTR, SOL, WM) on board. 4. Gently remove appropriate sensor/mounting block assembly from panel by moving block sideways until edge of block clears retaining tab of panel. 5. Inspect lens and sensor assembly for foreign material and remove using non-abrasive cleaner. 6. Turn dispenser power on and test sensor by moving hands through activation area (no cl
Streszczenie treści zawartej na stronie nr. 19
Ice transport tube replacement Top mount ice machines, model C/E110CT400A/W Only use tubing supplied by Follett Corporation. ! 3 2 1 TIGHTEN CLAMP SCREW 4 Ice transport tube replacement Models C/E110FB400A/W, C/E110CR400A/W Correct installation of ice transport tube is critical to Satellite-fill icemaker performance. Replacement ! ice transport tubes for Satellite-fill icemakers must be insulated and run continuously from icemaker to dispenser with no dips or bends with a radius of le
Streszczenie treści zawartej na stronie nr. 20
All units 9. Slip supplied hose clamp onto tube and push tube onto exit port of evaporator. Do not twist hose when securing to evaporator. Only use tubing supplied by Follett Corporation. ! 10. Fasten tube on port with hose clamp, being sure that clamp is positioned on evaporator side of nozzle flange. 11. Tighten clamp. ice level control stat engaging pin capillary tube 26mm (1") ice tube ice hose mounting bracket 5mm (3/16") ice tube hole 20
