Streszczenie treści zawartej na stronie nr. 1
DO NOT
DISCARD
Owner’s Manual
Installation and Operation
Model:
SLR (Cosmo)
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating • Read, understand and follow • Leave this manual with
and maintenance these instructions for safe
party responsible for use
instructions included. installation and operation.
and operation.
WARNING
WARNING: If the information in these
HOT SURFACES!
instructions is not followed exactly, a fi re
Glass and other surfaces are hot during
or explosion may result ca
Streszczenie treści zawartej na stronie nr. 2
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. This owner’s manual should be retained for future A. Congratulations reference. We suggest that you keep it with your other Congratulations on selecting a Heat & Glo gas fi replace, an important documents and product manuals. elegant and clean alternative to wood burning fi replaces. The information contained in this owner’s manual, unless The Heat & Glo gas fi replace you h
Streszczenie treści zawartej na stronie nr. 3
Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. • CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. • NOTICE: Used to address practices not related to personal injury. Table of Contents A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Streszczenie treści zawartej na stronie nr. 4
13 Finishing A. Framing and Finishing Instructions . . . . . . . . . . . . . . . . . 47 B. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 50 C. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 D. Decorative Fronts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 14 Appliance Setup A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 54 B. Remove the Shipping Materials . . . . . . . . . . . . . .
Streszczenie treści zawartej na stronie nr. 5
B. Limited Lifetime Warranty LIMITED LIFETIME WARRANTY HEAT & GLO GAS APPLIANCE PRODUCTS BASIC ONE-YEAR WARRANTY. HEAT & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard, Lakeville, MN 55044, (“HEAT & GLO”) warrants to the original owner that your new HEAT & GLO Gas Appliance (the “Product”) will be free from defects in materials and workmanship for a period of one year from the date of installation. During the fi rst year, HEAT & GLO will replace or rep
Streszczenie treści zawartej na stronie nr. 6
Listing and Code Approvals 1 1 A. Appliance Certifi cation C. BTU Specifi cations Minimum Orifi ce Maximum Models MODEL: SLR Input Size Input BTU/h (U.S. or Canada) BTU/h (DMS) LABORATORY: Underwriters Laboratories, Inc. (UL) US 26,000 N/A #42 (0-2000 FT) TYPE: Vented Gas Fireplace Heater SLR (NG) CANADA STANDARD: ANSI Z21.88a-2007 CSA 2.33a-2007 (2000-4500 21,870 N/A #43 Vented Gas Fireplace Heaters FT) US This product is listed to ANSI standards for “Vented Gas 25,000 N/A .057 (0-2000 FT
Streszczenie treści zawartej na stronie nr. 7
Inspection Note: The following requirements reference various The state or local gas inspector of the side wall horizon- Massachusetts and national codes not contained in this tally vented gas fueled equipment shall not approve the document. installation unless, upon inspection, the inspector ob- serves carbon monoxide detectors and signage installed G. Requirements for the Commonwealth of in accordance with the provisions of 248 CMR 5.08(2)(a)1 Massachusetts through 4. For all side wall
Streszczenie treści zawartej na stronie nr. 8
User Guide Operating Instructions 2 2 • Keep remote controls out of reach of children. A. Gas Fireplace Safety • Never leave children alone near a hot fi replace, whether operating or cooling down. WARNING • Teach children to NEVER touch the fi replace. HOT SURFACES! Glass and other surfaces are hot during • Consider not using the fi replace when children will be operation AND cool down. present. Hot glass will cause burns. Contact your dealer for more information, or visit: www. • DO NOT to
Streszczenie treści zawartej na stronie nr. 9
CLEAR SPACE 3 FT. IN FRONT OF FIREPLACE C. Clear Space E. Fixed Glass Assembly WARNING! DO NOT place combustible objects in front See Section 14.F. of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. F. Remote Controls, Wall Controls and Wall Avoid placing candles and other heat-sensitive objects on Switches mantel or hearth. Heat may damage these objects. Follow the instructions supplied with the control installed to operate your fi replace: For safety: •
Streszczenie treści zawartej na stronie nr. 10
H. Lighting Instructions (IPI) The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer. FOR YOUR SAFETY LIGHTING READ BEFORE LIGHTING INSTRUCTIONS (IPI) WARNING: If you do not follow these instructions exactly, a fi re or explosion may result causing property damage, personal injury or loss of life. 1. Turn off all electric power to the appliance. • Immediately call your gas supplie
Streszczenie treści zawartej na stronie nr. 11
I. After Fireplace is Lit Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • Turn the fi replace off and allow it to completely cool. • Remove fi xed glass assembly. See Section 14.F. • Clean fi xed glass assembly. See Section 3. • Replace the fi xed glass assembly and run continuously on high an additional 12 hours. This cures the materials used to manufacture the fi re- place. NOTICE! Open windows for air circulation during fi re- place break-in.
Streszczenie treści zawartej na stronie nr. 12
Maintenance and Service 3 3 Doors, Surrounds, Fronts Any safety screen or guard removed for servicing must be replaced prior to operating the fi replace. Frequency: Annually By: Homeowner When properly maintained, your fi replace will give you many years of trouble-free service. We recommend an- Tools needed: Protective gloves, stable work surface nual service by a qualifi ed service technician. • Assess condition of screen and replace as necessary. A. Maintenance Tasks-Homeowner • Insp
Streszczenie treści zawartej na stronie nr. 13
have penetrated the sheet metal are sharp and should Venting be avoided. Frequency: Seasonally • Remove all foreign objects. By: Homeowner • Verify unobstructed air circulation. Tools needed: Protective gloves and safety glasses. Burner Ignition and Operation • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, Frequency: Annually etc. By: Qualifi ed Service Technician • Verify termination cap clearance to subsequent construc- To
Streszczenie treści zawartej na stronie nr. 14
Installer Guide Getting Started 4 4 A. Typical Appliance System NOTICE: Illustrations and photos refl ect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual HORIZONTAL TERMINATION CAP (SECTION 7) WALL PENETRATION FRAMING (SECTION 8B) VERTICAL TERMINATION CAP (SECTION 10) NON-COMBUSTIBLE ROOF FLASHING MAINTAINS MINIMUM CLEARANCE AROUND PIPE STORM COLLAR (SECTION 10) (SECTION 10) VENT PIPE PE
Streszczenie treści zawartej na stronie nr. 15
B. Design and Installation Considerations D. Inspect Appliance and Components Heat & Glo direct vent gas appliances are designed to • Carefully remove the appliance and components from operate with all combustion air siphoned from outside of the packaging. the building and all exhaust gases expelled to the outside. • The vent system components and decorative doors and No additional outside air source is required. fronts may be shipped in separate packages. Installation MUST comply with loca
Streszczenie treści zawartej na stronie nr. 16
Framing and Clearances 5 5 It is important to follow the framing and fi nishing A. Selecting Appliance Location instructions step by step to ensure proper placement of When selecting a location for the appliance it is important to fi replace in the surrounding framing/fi nishing materials. consider the required clearances to walls (see Figure 5.1). WARNING! Risk of Fire or Burns! Provide adequate Unlike many traditional, single sided Heat & Glo fi replaces, clearance around air openings and
Streszczenie treści zawartej na stronie nr. 17
B. Constructing the Appliance Chase C. Clearances A chase is a vertical box-like structure built to enclose the NOTICE: Install appliance on hard metal or wood surfaces gas appliance and/or its vent system. In cooler climates extending full width and depth. DO NOT install directly the vent should enclosed inside the chase. on carpeting, vinyl, tile or any combustible material other than wood. NOTICE: Treatment of ceiling fi restops and wall shield fi restops and construction of the chase may v
Streszczenie treści zawartej na stronie nr. 18
D. Mantel and Wall Projections Combustible Mantel Legs Or Wall Projections Extending Past The Face Of The Fireplace WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as specifi ed. Framing or fi nishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, concrete board, etc). Combustible Mantels 2 IN. 1/2 in. 3 FT. MAXIMUM MINIMUM Thick Wall 12 in. Sheathing MAX. 6 IN. MINIMUM Figure 5.5 Combustibl
Streszczenie treści zawartej na stronie nr. 19
1/2 in. SHEETROCK 3-1/2 in. NON-COMBUSTIBLE BOARD SHIPPED WITH APPLIANCE 1 in. 1-9/16 in. AIR SPACE Figure 5.8 Non-Combustible Zone Heat & Glo • SLR • 2143-900 Rev. B • 7/08 19
Streszczenie treści zawartej na stronie nr. 20
Termination Locations 6 6 A. Vent Termination Minimum Clearances DIRECT VENT GAS, WOOD OR FUEL OIL TERMINATION B WARNING C Fire Risk. Maintain vent clearance to combustibles as A specifi ed. • DO NOT pack air space with insulation or other GAS materials. TERMINATION Failure to keep insulation or other materials away from vent pipe may cause overheating and fi re. HORIZONTAL OVERHANG Minimum Dimensions Wood & Fuel Oil Comments Termination Termination 2 FT. 20 INCHES MIN. VERTICAL MIN. A 6 in
