Streszczenie treści zawartej na stronie nr. 15
™ CLRCO2075 — Clear Ice Maker/Refrigerator 5. Place a suitable container beneath the pump’s discharge CAUTION tube. (The bucket must be able to hold a minimum of one gallon.) In the event of a power outage, restricted drain or pump failure, the failure to use the U-Line P60 drain pump or a 6. Plug the ice maker power cord into a properly pump with the above listed specifications, could result in grounded, polarized electrical outlet. substantial water leakage and pooling with severe and 7
Streszczenie treści zawartej na stronie nr. 16
™ CLRCO2075 — Clear Ice Maker/Refrigerator 3. Carefully bend the water supply line into position and 7 Prepare Power Supply connect the line to the solenoid valve (see Figure 39). Avoid kinking the water supply line. Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a qualified electrician. The unit requires a grounded and polarized 115 VAC,
Streszczenie treści zawartej na stronie nr. 17
™ CLRCO2075 — Clear Ice Maker/Refrigerator 2. If the ice maker is not level, adjust the feet on the 8 Level the Unit corners of the unit as necessary (see Figure 43). Leveling Information IMPORTANT It is extremely important that the unit is level. If it is not level, the ice mold will not fill evenly. A unit that is not level can cause a reduction in ice rate, Turn Foot to Adjust uneven sized cubes or water spilling into the storage area, which will cause the ice Figure 43 in the bin to
Streszczenie treści zawartej na stronie nr. 18
™ CLRCO2075 — Clear Ice Maker/Refrigerator Door Shelves 9 Install the Unit 1. First pull shelf up at a 45° angle, then straight out Installation of the CLRCO2075 (see Figure 45). Notch 1. Open the water supply valve in the main water source. 2. Choose new location and line up on bosses. First 2. Make sure the cycle selector switch is in the OFF push straight in, then (middle) position (see Figure 46). down at a 45° angle. Note: If the cycle selector switch is in the ON or CLN Boss positio
Streszczenie treści zawartej na stronie nr. 19
™ CLRCO2075 — Clear Ice Maker/Refrigerator Temperature Controller 10 Start-Up for the First Time The temperature controller (Figure 47) is located below the clear ice maker. It consists of an LED display, three LED Initial Start-Up status indicator lights and three touchpad buttons. The LED display shows the temperature set point and is Once installation and leveling is complete, the unit is calibrated in degrees Fahrenheit. The controller is factory ready for initial start-up and operatio
Streszczenie treści zawartej na stronie nr. 20
™ CLRCO2075 — Clear Ice Maker/Refrigerator Start-Up Troubleshooting Problem Q: Unit does not appear to turn on when switch is set to ON. Solution A: Remember that the compressor will not operate until the water has been filling for about 3 minutes. Make sure unit is plugged in and outlet has power (circuit breaker has not tripped). If the unit is equipped with a drain pump, check that the drain line is not obstructed (LED #3 will blink) — unit will shut down due to the safety design of th
Streszczenie treści zawartej na stronie nr. 1
™
Installation Guide
CLRCO2075 —
Clear Ice Maker/Refrigerator
www.U-LineService.com
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 FAX (414) 354-5696
OnlineService@U-Line.com
©2005 U-Line Corporation
02/2005
Streszczenie treści zawartej na stronie nr. 2
™ CLRCO2075 — Clear Ice Maker/Refrigerator Contents 1 Follow Safety Precautions Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 IMPORTANT Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PLEASE READ all instructions completely before Door Swing/Clearances Information . . . . . . . . . . . . . . 5 attempting to install or operate the unit. Reversing the Door.
Streszczenie treści zawartej na stronie nr. 3
™ CLRCO2075 — Clear Ice Maker/Refrigerator General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed You have received a carton containing your CLRCO2075 throughout this guide: Clear Ice Maker/Refrigerator with a package inside containing a User Manual, a Product Registration Card WARNING and water connection parts. Complete and mail the Product Registration Card or register online at SHOCK HAZARD —
Streszczenie treści zawartej na stronie nr. 4
™ CLRCO2075 — Clear Ice Maker/Refrigerator After all the protective coating has been removed from 3 Prepare Site the unit/door, clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft Your U-Line product has been designed for either free- cloth. Do NOT use abrasive cleaning agents. standing or built-in installation. When built-in, your unit does not require additional air space for top, sides
Streszczenie treści zawartej na stronie nr. 5
™ CLRCO2075 — Clear Ice Maker/Refrigerator Product Dimensions Reversing the Door (Black and White Units Only) 24" 26-1/8" Including Including All U-Line units (except Handle Handle Stainless Steel models) may be left- or right-hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side. The top hinge 34-1/8" 34-1/8" hardware will be used on the bottom of the other side and the bottom hinge hardware will be used on the top of the other side (see
Streszczenie treści zawartej na stronie nr. 6
™ CLRCO2075 — Clear Ice Maker/Refrigerator 4. Remove the two door closer inserts from the existing Other Site Requirements bottom hinge and install as shown on the new bottom hinge (see Figure 8). Power Supply The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). See Electrical Specifications on Page 16. Hinge Screw Water Supply Pin Door The unit requires a 1/4-inch OD water supply line and a Closer shut-off valve. For more information see Page 1
Streszczenie treści zawartej na stronie nr. 7
™ CLRCO2075 — Clear Ice Maker/Refrigerator Side-By-Side Installation 4 Prepare and Install Door Panel Instructions (Black and White Units Only) For a complete refreshment center, install your CLRCO2075 Clear Ice Maker/Refrigerator beside a U-Line Two types of custom door panels can be installed on your Drawer or Wine Captain Model (see Figure 11 for typical Black or White unit to harmonize with or accent the cut-out). Note that each Side-By-Side Installation will be surrounding décor: a C
Streszczenie treści zawartej na stronie nr. 8
™ CLRCO2075 — Clear Ice Maker/Refrigerator Full Overlay Door Panel Door Panel Preparation A full overlay door panel completely covers the doorframe and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit (P/N U-OL2075B — Black or P/N U-OL2075W — White). Appropriate hardware, Modified Handle, Replacement Hinges and a copy of these instructions will be included in the kit. 1. Cut the overlay to the following dimensions (see Figure 15). F
Streszczenie treści zawartej na stronie nr. 9
™ CLRCO2075 — Clear Ice Maker/Refrigerator 4. Drill hole for upper door hinge (top of panel) (see 13/32" 0.177" Dia. (#16 Drill) Figure 16, Top View). 13/32" x 11/16" Deep 0.177" diameter 3/8" (#16 drill) x 11/16" deep 3/8" 5. Drill hole for lower door hinge (see Figure 16, Bottom Door Bottom: 13/16" View). x 5/16" Dia. 1/4" Deep x Chamfer 1/32" 45° 5/16" diameter x 1/4" deep Top View Bottom View CAUTION It is important to ensure that all drilled holes are drilled to 1/8" 1/8" 13/32" 1/8"
Streszczenie treści zawartej na stronie nr. 10
™ CLRCO2075 — Clear Ice Maker/Refrigerator 5. Remove the top handle and discard. (This handle will be Tape replaced with the Modified Handle included in the Full Back of Removed Wood Overlay Door Panel Kit.) Door Panel Panel 6. Remove the two screws located on both sides of the lower handle. Remove the handle. 7. Attach the Modified Handle to the lower handle using the three screws removed in Step 4. Set aside. 8. Slide the existing door panel out of the doorframe. Side of Attaching the Full
Streszczenie treści zawartej na stronie nr. 11
™ CLRCO2075 — Clear Ice Maker/Refrigerator Typical Door Panel Pivot Post Wood Panel Wood Panel Top Hinge Plate Top (5/8" Longer than Existing Top Hinge Plate) Pivot Plate x #10 5/8" x #8-32 1/2" Round Head Screw Flat Head Screw Seven Required Three Places Plastic Spacer Top Pivot Plate Seven Required Figure 22 Door Panel 5. Remove the existing bottom pivot plate and replace Figure 24 with the Full Overlay pivot plate (see Figure 23). 3. Install the pivot post into the new Replacement Bottom
Streszczenie treści zawartej na stronie nr. 12
™ CLRCO2075 — Clear Ice Maker/Refrigerator 5 Adjust Door Checking Door Alignment The unit’s door is aligned at the factory before shipment. Slotted However, its alignment could have been disturbed during Mounting Notch Holes shipment or during door panel installation. IMPORTANT Properly aligned, the door should be 1/8" below the top of the unit’s cabinet, NOT flush with the top (see Figure 26). Raise Lower Outside Outside Door Edge Door Edge Figure 28 1/8" 3. See Figure 28. If the top far edg
Streszczenie treści zawartej na stronie nr. 13
™ CLRCO2075 — Clear Ice Maker/Refrigerator Gravity Drain 6Prepare Plumbing CAUTION Plumbing installation must observe all state and local codes. All water and drain connections MUST BE made by Waste a licensed/qualified plumbing contractor. Failure to follow Shut-Off recommendations and instructions may result in damage Valve and/or harm. Cold Water Hot Drain Connection Water IMPORTANT Drain can NOT be located directly below unit. Unit has a Waste Figure 31 solid base that will not allow un
Streszczenie treści zawartej na stronie nr. 14
™ CLRCO2075 — Clear Ice Maker/Refrigerator To check and test hose connections: Disposal Assembly 1. Make certain the unit is not plugged into an electrical Air Gap outlet. (Optional Hook-Up) 2. Carefully push the power cord grommet through the hole in the back panel (see Figure 35). Waste Screws Back Panel Cold Hot Water Water Shut-Off Valve Figure 33 Spigot Assembly Air Gap Grommet (Optional Hook-Up) Water Drain Connection Power Fitting Cord Figure 35 Waste Shut-Off 3. Remove 12 screws and ba
