Streszczenie treści zawartej na stronie nr. 1
NAILER/STAPLER
OIL FREE - 18 GAUGE
Model 95218
ASSEMbLy ANd OPERATION INSTRUcTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
TO PREVENT SERIOUS INjUR y, REAd ANd UNdERSTANd
ALL wARNINGS ANd INSTRUcTIONS bEFORE USE.
© ®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein
Streszczenie treści zawartej na stronie nr. 2
PROdUcT SPEcIFIcATIONS Fastener Capacity 18 Gauge (5/8” – 2” Brads) / (5/8” – 1-5/8” Staples) 1/4” Crown Magazine Capacity 100 Fasteners Load Style Top Loading Magazine Operating PSI 125 PSI Maximum* Average Air Flow 3.0 CFM Air Inlet Size 1/4”-18 NPT Safety Trigger Mechanism Single Sequential Accessories Hex Wrenches (Qty. 2) Weight 3.15 Pounds *The air pressure setting must not exceed job site regulations/restrictions. The air pressure setting must not exceed 90 PSI when being used with wor
Streszczenie treści zawartej na stronie nr. 3
6. dress properly. Do not wear loose clothing or jewelry as they can be caught in mov- ing parts. Protective, electrically non-conductive clothes and non-skid foot-wear are recommended when working. Wear restrictive hair covering to contain long hair. 7. do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. 8. Use eye and ear protection. Always wear ANSI-approved impact safety goggles and appropriate hearing protection
Streszczenie treści zawartej na stronie nr. 4
16. do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 17. Use proper size and type extension cord for an air compressor. If an exten- sion cord is required, it must be of the proper size and type to supply the correct current to the compressor without heating up. Otherwise, the extension cord could me
Streszczenie treści zawartej na stronie nr. 5
Crystalline silica from bricks and cement or other masonry products Arsenic and chromium from chemically treated lumber Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are spe- cially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.) 26. Stay within air pres
Streszczenie treści zawartej na stronie nr. 6
TESTING THE SINGLE SEQUENTIAL SAFETy TRIP MEcHANISM wARNING: Even though the Nailer should be empty during this procedure, ALWAYS point the Nailer at a piece of scrap wood when testing. Always wear ANSI-approved safety goggles. 1. Make sure the tool is disconnected from its air supply. 2. Completely empty the Moveable Magazine (61) of Brads or Staples. AIR INLET PLUG (78) TRIGGER (32) FIXEd LEVER (53) MOVEAbLE MAGAZINE (61) dRIVER GUIdE (62) 3. The Nailer/Stapler should not fire if the Drive
Streszczenie treści zawartej na stronie nr. 7
LOAdING bRAdS ANd STAPLES wARNING: Always wear ANSI-approved impact safety goggles when us- ing, reloading, or performing any other maintenance on this tool. Other people in the work area must also wear ANSI-approved impact safety gog- gles. Note: Do not mix brads and staples. Load the magazine with only one type. 1. Lift the Fixed Lever (53) and slide the Moveable Magazine (61) back until it locks in place. AIR INLET PLUG (78) LOAd bRAdS OR STAPLES TRIGGER HERE. (32) FIXEd LEVER (53) dRIVER
Streszczenie treści zawartej na stronie nr. 8
OPERATING THE NAILER/STAPLER 1. Attach the Nailer/Stapler to the air supply at the Air Inlet Plug (78). Start your com- pressor and check the pressure, making sure it is set no higher than 125 PSI. do not exceed the maximum 125 PSI. 2. Rotate the Air Deflector (3) so that the exhaust air blast will be directed away from the operator. 3. To fire, place the Driver Guide (62) of the tool on the workpiece. The Nailer/Stapler should not fire if the Driver Guide is not depressed. Once depressed,
Streszczenie treści zawartej na stronie nr. 9
Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer/Stapler from its air supply. 2. Empty the Moveable Magazine (61) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any Brads/Staples. 4. Wear ANSI-approved safety goggles, if not already doing so. cLEARING j AMS Use eye and ear protection when clearing jams. Always wear ANSI- approved impact safety goggles and app
Streszczenie treści zawartej na stronie nr. 10
Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer/Stapler from its air supply. 2. Empty the Moveable Magazine (61) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any Brads/Staples. 4. Wear ANSI-approved safety goggles, if not already doing so. INSPEcTION, MAINTENANcE, ANd cLEANING 1. Inspect the air supply Screen that is located in the End Cap (77) before each
Streszczenie treści zawartej na stronie nr. 11
PLEASE REAd THE FOLLOwING cAREFULL y THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESS- LY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,
Streszczenie treści zawartej na stronie nr. 12
ASSEMbLy dIAGRAM 78 1 77 74 2 14 76 22 3 75 53 52 4 5 15 73 51 50 49 72 71 16 54 24 25 56 55 37 48 47 17 26 46 33 6 5 45 4 23 32 44 31 27 7 33 28 18 31 34 8 29 36 35 58 30 9 19 37 38 61 64 63 62 59 10 60 39 68 11 40 20 41 12 42 13 21 70 43 69 65 64 67 79: Hex wrenches (Qty. 2) not shown. 66 Limited 90 d y a arrantyw Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free
