Streszczenie treści zawartej na stronie nr. 1
8 INCH DRILL PRESS
MODEL 44506
ASSEMBLY AND OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
© ®
Copyright 2000 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Streszczenie treści zawartej na stronie nr. 2
Specifications Control IN TEM DESCRIPTIO # 86PJ 120 110 VAC, 60 Hz, 1/3 HP, 1750 RPM; Motor 3.6 amps (with load) E172674 S. pindle Speeds 620, 1100, 1720, 2340, and 3100 RPM Sh pindle Stroke 2 inc Cs olumn 1.89 (diameter) x 15-1/4 (H) inche Bh ase Dimensions 11-1/8 x 7 inches; Slot: 9/16 inc Os verall Dimensions 23 (H) x 15-5/8 (D) x 7-1/2 (W) inche T) hroat Depth 4 inches (of 8 inch swing Ch huck Capacity Up to 1/2 inc Ts able Slot 5/8 inche T) able Rotation 360°; Tilt: 45° (left and right Ts a
Streszczenie treści zawartej na stronie nr. 3
6. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrict
Streszczenie treści zawartej na stronie nr. 4
19. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 20. Use proper size and type extension cord. If an extension cord is required, it must be of the proper size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the
Streszczenie treści zawartej na stronie nr. 5
9. Do not mount (or adjust) the workpiece on the Drill Press Table while the motor is running. 10. When drilling or cutting large holes, use the slower speeds and securely fasten the workpiece to the table using a mounted vise. 11. Do not use drill bits that extend more than six inches from the Chuck. 12. Do not use circle cutters, rotary planers, wire wheels, router bits, or shaper cutters on this Drill Press. Unpacking When unpacking, check to make sure the following parts are included. Refer
Streszczenie treści zawartej na stronie nr. 6
4. Install the Table Support (C1), with attached Table (C7), over the Support Tube (C3) and slide it down. Hand Tighten the Lock Handle Support (C2). CAUTION: Avoid injuries. The next step involves lifting the Head Assembly onto the Support Tube. The Head Assembly is heavy. Have someone help you lift this assembly into place. 5. Using two people, lift the Head (1) Assembly up and onto the Support Tube (C3). Slide it down on the Column Tube as far as it will go. Align it so that it faces straigh
Streszczenie treści zawartej na stronie nr. 7
- Slide the Chuck onto the Spindle Shaft. - Turn the Chuck sleeve clockwise and open the jaws completely. - Tap the nose of the Chuck lightly with a piece of wood and a hammer to securely set the Chuck. 11. Verify that the Table (C7) is square (90 degrees) to the Screw (C6) Head Assembly and drill bit. - Raise the Table to within four inches of the Chuck. - Place the long side of a combination square on the Table. - Align the short side of the square to the drill bit. - If the Table is not sq
Streszczenie treści zawartej na stronie nr. 8
Setting the Depth Scale to Drill to a Specified Depth During this procedure, refer to the left photo on page 6. 1. Make sure the Drill Press is OFF and Power Cord (33) is unplugged. Secure the workpiece to the Table. 2. Mark the desired hole depth on the side of the workpiece. Also view the depth indicator Pointer (32) shown on page 9. 3. Loosen the Hex Nuts (31) and screw both toward the top of Stop Rod (B12). 4. Turn the Feed Wheel counterclockwise to bring the tip of the drill bit down, next
Streszczenie treści zawartej na stronie nr. 9
2. Slide the Spindle Shaft and Chuck assembly up and into the Quill Tube (B3). At the same time, turn the assembly until the rectangular end of the Spindle Shaft slips into the notch on the Quill Tube. Warning: In the previous step, if the Spindle Shaft is not properly set in the Quill Tube notch, it may fly out during operation. 3. Loosen the Lock Handle Support (C2) and raise the Table (C7) about three inches below the Chuck. 4. Turn the Chuck sleeve clockwise to open the jaws completely. 5. P
Streszczenie treści zawartej na stronie nr. 10
8. Pull the Feed Knob and check the spring tension, making sure the up movement is smooth and complete. From one inch down, the Chuck should return to its uppermost position. If more tension is required, repeat steps. 9. Replace the (outer) Hex Nut and tighten on top of the (inner) Hex Nut. Do not overtighten. 10. If the (up/down) movement is restricted, slightly loosen the (inner) Hex Nut, and retighten the (outer) Hex Nut. General Maintenance 1. Using compressed air, blow clean the Table, Base
Streszczenie treści zawartej na stronie nr. 11
Troubleshooting SE YMPTOMPN OSSIBLE CAUS SOLUTIO - Incorrect spindle speed - Change spindle speed Drill bit burns or - Dull drill bit - Replace with new bit smokes - Drilling too slowly - Drill faster - Lacking lubrication - Lubricate cutting area - Belt tension set wrong - Adjust belt tension Makes unusual - Spindle dry - Lubricate spindle noise - Loose spindle pulley - Check pulley nut - Loose motor pulley - Tighten Set screws - Bent bit - Replace drill bit - Worn Spindle Bearings - Replace sp
Streszczenie treści zawartej na stronie nr. 12
Head Assembly Parts List In tem # Descriptio In tem # Descriptio 18 8 Screw, Pan Hd. M5x0.8- 1m Head w/ Roll Pin and Tri 1e 9 Box, Switch w/ Depth Scal 28 Nut, Lock, M8x1.25- 36 Washer, 5/16 x 11/16 x 1/122 0 Screw, Pan Cr., M5x0.8-1 2g 1 Switch, Lockin 45 Screw, Hex, M8x1.25-2 5r Pulley, Moto 28 2 Screw, Self Tap. Pan Hd. M4x16- 60 Screw, Hex Soc. Set, M6x1.0-12e 3 Cover, Switch Plat 7r Moto 2h 4 Key, Switc 8r Stop, Moto 2e 5 Connector, Wir 9p Spring, Motor Sto 2g 6 Seat, Sprin 1g 0 Knob, Motor
Streszczenie treści zawartej na stronie nr. 13
Head Assembly Drawing SKU 44506 For technical questions, please call 1-800-444-3353. Page 13
Streszczenie treści zawartej na stronie nr. 14
Pulley and Spindle Assembly Parts List In tem # Descriptio Ar 1 Bushing, Rubbe Ab 2 Kno A2 3 Screw, Pan Hd., M5x0.8-1 A6 4 Belt, V5, 5/16x2 As 5 Guard with Label A6 6 Screw-washer Hd., M6x10-1 Ag 7 Ring, Retainin Am 8 Bearing, Ball, 17 m Ar 9 Space Ay 10 Insert, Pulle Ae 11 Pulley, Spindl Ay 12 Nut, Pulle Ad 13 Clamp, Cor A6 14 Screw, Pan Hd., M5x0.8-1 Am 15 Washer, Foa Pulley and Spindle Assembly Drawing When ordering a part from this drawing, add an A- prefix to the part number. SKU 44506
Streszczenie treści zawartej na stronie nr. 15
Chuck and Spindle Shaft Parts List In tem # Descriptio Bl 1 Gasket, Quil Bm 2 Bearing, Ball, 12 m Bl 3 Tube, Quil B0 4 Screw, Pan, M5x0.8-2 Bp 5 Collar, Sto Bg 6 Ring, Retainin Be 7 Shaft, Spindl Bk 8 Chuc By 9 Chuck Ke B0 10 Nut, Hex, M6x1. B8 11 Nut, Hex, M5x0. Bd 12 Stop, Ro Chuck and Spindle Shaft Assembly Drawing When ordering a part from this drawing, add a B- prefix to the part number. SKU 44506 For technical questions, please call 1-800-444-3353. Page 15
Streszczenie treści zawartej na stronie nr. 16
Base and Table Assembly Parts List In tem # Descriptio Ce 1 Support, Table with Scal Ce 2 Support, Lock Handl Ct 3 Tube, Suppor Ce 4 Bas C0 5 Screw, Hex Hd., M8x1.25-2 C8 6 Screw, Hex Hd., 1/2-12x7/ Ce 7 Tabl Base and Table Assembly Drawing When ordering a part from this drawing, add a C- prefix to the part number. SKU 44506 For technical questions, please call 1-800-444-3353. Page 16
