Streszczenie treści zawartej na stronie nr. 1
English Español
For Your Records and
Warranty Assistance
T T Type 7 Models ype 7 Models ype 7 Models
For reference, also attach your
receipt or a copy
of your receipt to the manual.
Owner’s Guide and Installation Manual
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 45084-01
20120117
©2012 Hunter Fan Co.
Streszczenie treści zawartej na stronie nr. 2
Welcome Your new Hunter ceiling fan is an addition to your home or office that ® will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your fan. We are proud of our work. We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. Before installing your fan, for your records and warranty assistance, record information from the carton and Hunter namepl
Streszczenie treści zawartej na stronie nr. 3
Preparing the Fan Site Step 1 - Choose the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety, reliable operation, maximum efficiency, and energy savings. 30” From 9’ Minimum Choose a fan site where: Wall or Ceiling Nearest • No object can come in contact with the rotating fan blades during Obstruction 7’ Minimum Height Blades to normal operation. Floor • The fan blades are at least 7 feet above the floor and the ceiling is at least 9
Streszczenie treści zawartej na stronie nr. 4
Preparing the Fan Site (continued) Step 2 - Cut the Ceiling Hole 2-1. Locate the site for the ceiling hole directly below the joist or support brace that will hold the outlet box and fan. 2-2. Cut a 4” diameter hole through the drywall or plaster of the ceiling. You will use the hole to install the support brace and outlet box. Step 3 - Install a Support Brace, If Necessary Determine if there is a ceiling joist directly above the ceiling hole. If the joist is there, determine if it is positio
Streszczenie treści zawartej na stronie nr. 5
Installer’s Choice and Optional Accessories Understanding Mounting and Installer’s Choice® Support Brace Hunter’s patented 2-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depending on ceiling height and your preference: Standard or Angled mounting. The steps in this manual include instructions for Ceiling Standard both Installer’s Choice mounting methods. Outlet Box Mounting Style Considering Optional Ac
Streszczenie treści zawartej na stronie nr. 6
1 • Getting Ready To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling. • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: • Electric drill with 9/64” bit • Keyhole saw • 2’ x 4’ suppo
Streszczenie treści zawartej na stronie nr. 7
2 • Installing the Hanger Bracket 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64” Isolator in diameter. Hanger Note: Your fan comes with four pre-installed neoprene noise Bracket isolators. 2-2. Thread the lead wires from the outlet box down through the hole in the middle of the hanger bracket. 2-3. Align the slotted holes in the hanger bracket with the pilot holes you drilled in the wood support s
Streszczenie treści zawartej na stronie nr. 8
3 • Assembling and Hanging the Fan Steps 3-1 – 3-3 3-1. To assemble fan to hang down from a flat or angled ceiling, place the canopy and canopy trim ring around the adapter so that they rest on the fan assembly. Downrod 3-2. Feed the wires from the fan through the downrod. Note: Make sure all the wires are on the same side of the metal dowel pin inside the downrod. 3-3. Loosen the square head setscrew on the adapter to install the pipe Canopy and ball assembly. Note: When the pipe and b
Streszczenie treści zawartej na stronie nr. 9
4 • Securing Fan to Secondar y Support System Step 4-1 4-1. Loosen the two nuts on the wire clamp. Slide the clamp open. 4-2. Insert the end of the braided cable through the ceiling plate and one of the holes in the outlet box into the ceiling. 4-3. Access the support brace in the ceiling. You may not be able to do this from below the ceiling, depending on your installation site. Wire Clamp Step 4-2 4-4. Thread the end of the cable up through the wire clamp. 4-5. Wrap the braided cab
Streszczenie treści zawartej na stronie nr. 10
5 •Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-use switch in accordance with national and local electrical codes. 5-1. Before attempting installation, make sure the power is still off. 5-2. To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise u
Streszczenie treści zawartej na stronie nr. 11
6 • Installing the Canopy and Canopy Trim Ring Steps 6-1 – 6-2 Hanger Bracket 6-1. Partially install two canopy screws (about 2 full turns) in the hanger bracket. 6-2. Raise the canopy over the hanger bracket. Align partially installed screws with key slots in canopy. 6-3. Twist canopy clockwise to secure. 6-4. Install third & fourth canopy screw in round hole on canopy. Securely tighten all four screws. Canopy Trim Ring Canopy 6-5. Using both hands, push the canopy trim ring up to the t
Streszczenie treści zawartej na stronie nr. 12
7 • Assembling the Blades You have the option of installing three blades or six blades on your fan. Install one blade iron for three blades and two blade irons for six. 7-1. Remove the blade mounting screws and rubber shipping bumpers from the motor. 7-2. Attach a blade iron to the fan with three blade mounting screws. The blade mounting screws should be installed inside the holes in the centers of the three arms of the blade iron. 7-3. If you want to install six blades instead of thre
Streszczenie treści zawartej na stronie nr. 13
8 • Installing the Switch Housing Step 8-1 8-1. To attach the upper switch housing, partially install Mounting Plate #6-32 machine screws into the switch housing mounting plate. #6-32 8-2. Align the keyhole slots in the housing with the MachineScrew machine screws. 8-3. Turn the housing counterclockwise until the machine assembly screws are firmly situated in the narrow end of the keyhole slots. Install the remaining screw into the housing. Tighten all three screws firmly. CAUTION: M
Streszczenie treści zawartej na stronie nr. 14
9 • Assembling the Remote Control and Mounting the Cradle After removing the control from the box, shut off power to the room you will be working in at the breaker box. Caution: Do not restore power until all work is complete. 9-1. Pull the knob off of the speed Steps 9-1 – 9-4 control unit and remove your existing Black switch from the switch box. Black 9-2. Connect each black lead from the speed control to a black lead from the switch box with a wire connector. Note: If two white wires are
Streszczenie treści zawartej na stronie nr. 15
10 • Operating and Cleaning Your Ceiling Fan 10-1. Turn on electrical power to the fan. 10-2. The knob on the wall control unit controls power to the fan. The fan has three speed settings in sequence: High, Low and Off. 10-3. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in warm weather to cool the room with a direct breeze. In winter, having the fan draw air upward (clockwise blade rotation) will distribute the warmer air trapped at the ceiling around the
Streszczenie treści zawartej na stronie nr. 16
11 • Troubleshooting Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Remove the shipping bumpers. Problem: Noisy operation. 1. Tighten the blade assembly screws and blade iron armature screws until snug. 2. Check to see if the blade is cracked. If so, replace all the blades. Problem: Excessive wobbling. 1. If your fan wobbles when operating, use the enclosed ba
