Instrukcja obsługi Husqvarna 359 EPA III

Instrukcja obsługi dla urządzenia Husqvarna 359 EPA III

Urządzenie: Husqvarna 359 EPA III
Kategoria: Pila lancuchowa
Producent: Husqvarna
Rozmiar: 2.97 MB
Data dodania: 11/22/2014
Liczba stron: 44
Drukuj instrukcję

Pobierz

Jak korzystać?

Naszym celem jest zapewnienie Ci jak najszybszego dostępu do treści zawartych w instrukcji obsługi urządzenia Husqvarna 359 EPA III. Korzystając z podglądu online możesz szybko przejrzeć spis treści i przejść do strony, na której znajdziesz rozwiązanie swojego problemu z Husqvarna 359 EPA III.

Dla Twojej wygody

Jeżeli przeglądanie instrukcji Husqvarna 359 EPA III bezpośrednio na tej stornie nie jest dla Ciebie wygodne, możesz skorzystać z dwóch możliwych rozwiązań:

  • Przeglądanie pełnoekranowe - Aby wygodnie przeglądać instrukcję (bez pobierania jej na komputer) możesz wykorzystać tryp przeglądania pełnoekranowego. Aby uruchomić przeglądanie instrukcji Husqvarna 359 EPA III na pełnym ekranie, użyj przycisku Pełny ekran.
  • Pobranie na komputer - Możesz również pobrać instrukcję Husqvarna 359 EPA III na swój komputer i zachować ją w swoich zbiorach. Jeżeli nie chcesz jednak marnować miejsca na swoim urządzeniu, zawsze możesz pobrać ją w przyszłości z ManualsBase.
Husqvarna 359 EPA III Instrukcja obsługi - Online PDF
Advertisement
« Page 1 of 44 »
Advertisement
Wersja drukowana

Wiele osób woli czytać dokumenty nie na ekranie, lecz w wersji drukowanej. Opcja wydruku instrukcji również została przewidziana i możesz z niej skorzystać klikając w link znajdujący się powyżej - Drukuj instrukcję. Nie musisz drukować całej instrukcji Husqvarna 359 EPA III a jedynie wybrane strony. Szanuj papier.

Streszczenia

Poniżej znajdziesz zajawki treści znajdujących się na kolejnych stronach instrukcji do Husqvarna 359 EPA III. Jeżeli chcesz szybko przejrzeć zawartość stron znajdujących się na kolejnych strinach instrukcji, możesz z nich skorzystać.

Streszczenia treści
Streszczenie treści zawartej na stronie nr. 1


Operator’s manual
357XP EPA I 359 EPA III
Please read the operator’s manual carefully and make sure you understand the instructions
before using the machine. E En ng glliis sh h
E En ng glliis sh h

Streszczenie treści zawartej na stronie nr. 2

KEY TO SYMBOLS Symbols on the machine: Symbols in the operator’s WARNING! Chain saws can be manual: dangerous! Careless or improper Switch off the engine by moving the use can result in serious or fatal stop switch to the STOP position injury to the operator or others. before carrying out any checks or maintenance. Please read the operator’s manual carefully and make sure you understand the instructions before Always wear approved protective using the machine. g

Streszczenie treści zawartej na stronie nr. 3

KEY TO SYMBOLS You will find the following labels on your chain saw: EPA I EPA III The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual. The engine exhaust from this product contains chemi

Streszczenie treści zawartej na stronie nr. 4

CONTENTS FEDERAL EMISSION CONTROL WARRANTY Contents STATEMENT KEY TO SYMBOLS YOUR WARRANTY RIGHTS AND Symbols on the machine: ...................................... 2 OBLIGATIONS ..................................................... 42 Symbols in the operator’s manual: ........................ 2 AMERICAN STANDARD SAFETY PRECAUTIONS CONTENTS Safety precautions for chain saw users ................ 43 Contents .............................

Streszczenie treści zawartej na stronie nr. 5

INTRODUCTION Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water- powered plant. During over 300 years of continuous operation, the Husqvarna factory has produced a lo

Streszczenie treści zawartej na stronie nr. 6

WHAT IS WHAT? What is what on the chain saw? 1 Cylinder cover 17 Chain catcher 2 Front handle 18 Clutch cover 3 Chain brake and front hand guard 19 Rear handle with right hand guard 4 Starter 20 Throttle control 5 Chain oil tank 21 Throttle lockout 6 Starter handle 22 Decompression valve (Model 359) Automatic decompression valve (Model 357XP) 7 Adjuster screws carburetor 23 Combination spanner 8 Choke control/Start throttle lock 24 Chain tensioning screw 9 Rear handle 25 Operator’s

Streszczenie treści zawartej na stronie nr. 7

GENERAL SAFETY PRECAUTIONS Before using a new chain saw Important • Please read this manual carefully. IMPORTANT! • Check that the cutting equipment is correctly fitted The machine is only designed for cutting wood. and adjusted. See instructions under the heading You should only use the saw with the bar and chain Assembly. combinations we recommend in the chapter Technical • Refuel and start the chain saw. See the instructions data. under the headings Fuel Han

Streszczenie treści zawartej na stronie nr. 8

GENERAL SAFETY PRECAUTIONS possible. Your dealer, forestry school or your library can Generally clothes should be close-fitting without restricting provide information about which training materials and your freedom of movement. courses are available. IMPORTANT! Sparks can come from the muffler, the bar and chain or other sources. Always have fire extinguishing tools available if you should need them. Help prevent forest fires. Machine′′ ′′s safety equipment In this section the machine

Streszczenie treści zawartej na stronie nr. 9

GENERAL SAFETY PRECAUTIONS • The brake is applied when the front hand guard (B) is • To release the chain brake pull the front hand guard pushed forwards. backwards, towards the front handle. • This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine • Kickback can be very sudden and violent. Most drive system (D) (clutch drum). kickbacks are minor and do not always activate the chain brake. If this happens you should hold the chain saw firmly and

Streszczenie treści zawartej na stronie nr. 10

GENERAL SAFETY PRECAUTIONS of the front hand guard, the chain brake can only be (A) (i.e. when you grasp the handle) it releases the throttle activated by the inertia action. control (B). When you release the handle the throttle control and the throttle lockout both move back to their original positions. This arrangement means that the throttle control is automatically locked at the idle setting. Will my hand always activate the chain brake during a kickback? No. It takes a certain force t

Streszczenie treści zawartej na stronie nr. 11

GENERAL SAFETY PRECAUTIONS chain saw, including the cutting equipment, is insulated requiring among other things the muffler must be from the handles by vibration damping units. equipped with an approved type of spark arrestor screen. Cutting hardwoods (most broadleaf trees) creates more CAUTION! The muffler gets very hot during and after vibration than cutting softwoods (most conifers). Cutting use. This also applies during idling. Be aware of the fire with cutting equipment that is blunt or

Streszczenie treści zawartej na stronie nr. 12

GENERAL SAFETY PRECAUTIONS • Keep the chain properly tensioned! If the chain is Bar slack it is more likely to jump off and lead to increased • Length (inches/cm) wear on the bar, chain and drive sprocket. • Number of teeth on bar tip sprocket (T). • Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to break and lead to increased wear on the bar, chain and drive sprocket. • Chain pitch (inches). The spacing between the drive links of

Streszczenie treści zawartej na stronie nr. 13

GENERAL SAFETY PRECAUTIONS • Number of drive links. 4 Round file diameter It is very difficult to sharpen a chain correctly without the right equipment. We recommend that you use our file gauge. This will help you obtain the maximum kickback reduction and cutting performance from your chain. Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teeth • Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar t

Streszczenie treści zawartej na stronie nr. 14

GENERAL SAFETY PRECAUTIONS • File all the teeth to the same length. When the length resistance as you draw the file along the depth gauge of the cutting teeth is reduced to 0.16 inch (4 mm) the tool. chain is worn out and should be replaced. Tensioning the chain General advice on adjusting depth gauge setting • When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recomme

Streszczenie treści zawartej na stronie nr. 15

GENERAL SAFETY PRECAUTIONS The position of the chain tensioning screw on our chain throttle you should see a distinct line of oil on the light saws varies from model to model. See instructions under surface. the heading What is what? to find out where it is on your model. Lubricating cutting equipment WARNING! Poor lubrication of cutting equipment may cause the chain to snap, ! which could lead to serious, even fatal injuries. Chain oil Chain oil must demonstrate good adhesion to the chain

Streszczenie treści zawartej na stronie nr. 16

GENERAL SAFETY PRECAUTIONS Chain drive sprocket Bar The clutch drum is fitted with one of the following drive Check regularly: sprockets: • Whether there are burrs on the edges of the bar. Remove these with a file if necessary. A Spur sprocket (the chain sprocket is welded on the drum) B Rim sprocket (replaceable) • Whether the groove in the bar has become badly worn. Replace the bar if necessary. Regularly check the degree of wear on the drive sprocket. Replace if wear is

Streszczenie treści zawartej na stronie nr. 17

ASSEMBLY Tension the chain by turning the chain tensioning screw Fitting the bar and chain clockwise using the combination spanner. See instructions under the heading Tensioning the chain. WARNING! Always wear gloves, when working with the chain. ! Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up th

Streszczenie treści zawartej na stronie nr. 18

FUEL HANDLING Mixing ratio Fuel 1:50 (2%) for all engines. Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and Gasoline, litre Two-stroke oil, litre two-stroke oil. It is important to accurately measure the 2% (1:50) amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, 5 0,10 even small inaccuracies can drastically affect the ratio of 10 0,43/0,20 the mixture. 15 0,30 WARNING!

Streszczenie treści zawartej na stronie nr. 19

FUEL HANDLING • Never use waste oil. This results in damage to the oil Fuel safety pump, the bar and the chain. • Never refuel the machine while the engine is running. • It is important to use oil of the right grade (suitable • Make sure there is plenty of ventilation when refuelling viscosity range) to suit the air temperature. or mixing fuel (gasoline and 2-stroke oil). • In temperatures below 32°F (0°C) some oils become too viscous. This can overload the oil pump and result • Move the mac

Streszczenie treści zawartej na stronie nr. 20

STARTING AND STOPPING the machine has started the valve will automatically return Starting and stopping to its original setting. WARNING! Note the following before starting: A ! The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Never start a chain saw unless the bar, Warm engine chain and all covers are fitted correctly. Use the same procedure as for starting a cold engine but Otherwise the clutch can come


Podobne instrukcje
# Instrukcja obsługi Kategoria Pobierz
1 Husqvarna 115 13 82-49 Instrukcja obsługi Pila lancuchowa 168
2 Husqvarna 1151002-95 Instrukcja obsługi Pila lancuchowa 13
3 Husqvarna 115 13 81-96 Instrukcja obsługi Pila lancuchowa 15
4 Husqvarna 1150901-95 Instrukcja obsługi Pila lancuchowa 9
5 Husqvarna 115 13 82-95 Instrukcja obsługi Pila lancuchowa 5
6 Husqvarna 115 13 81-26 Instrukcja obsługi Pila lancuchowa 7
7 Husqvarna 115 13 82-96 Instrukcja obsługi Pila lancuchowa 2
8 Husqvarna 1151435-95 Instrukcja obsługi Pila lancuchowa 6
9 Husqvarna 1151187-95 Instrukcja obsługi Pila lancuchowa 2
10 Husqvarna 1150902-95 Instrukcja obsługi Pila lancuchowa 3
11 Husqvarna 115 13 81-95 Instrukcja obsługi Pila lancuchowa 1
12 Husqvarna 1151375-95 Instrukcja obsługi Pila lancuchowa 2
13 Husqvarna 1151338-95 Instrukcja obsługi Pila lancuchowa 3
14 Husqvarna 1151322-95 Instrukcja obsługi Pila lancuchowa 0
15 Husqvarna 1151437-95 Instrukcja obsługi Pila lancuchowa 5
16 Black & Decker 90559281 Instrukcja obsługi Pila lancuchowa 16
17 Black & Decker Saw CS1015 Instrukcja obsługi Pila lancuchowa 7
18 Black & Decker GKC1817NM Instrukcja obsługi Pila lancuchowa 14
19 Black & Decker CCS818 Instrukcja obsługi Pila lancuchowa 11
20 Black & Decker 3803-10 Instrukcja obsługi Pila lancuchowa 5