Instrukcja obsługi Makita HP1030

Streszczenie treści zawartej na stronie nr. 1

lOmm(3/8") MODEL HP1030
Variable Speed I Reversing
INSTRUCTION MANUAL
Hammer Drill & Standard Equipment
Tool
@ Depth rod
@ Grip 32
DOUBLE
@ Chuck key
INSULATION
Capacities Continuous rating No load Blow
Net 'Over
Overall
per length weight supp'y
cord
Metal Wood Concrete Input Output minute
10" 18mm lOmm 270" 1.6 kg 2m
(3/8") (314") (3/8") 430 200 oig:90 0-29.700
(10-5/8") (3.5 Ibs) (6.6 ft.)

Streszczenie treści zawartej na stronie nr. 2

IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence of flammable liquids or

Streszczenie treści zawartej na stronie nr. 3

replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Don't use tool if switch does not turn it on and off. 19. When drilling into walls, floors or whatever "live" electrical wires may be encoun- tered. DO NOT TOUCH THE CHUCK OR ANY FRONT METAL PARTS OF THE DRILL. Hold the Drill only by the plastic handle or the side grip to prevent electric shock if you drill into a ''live''

Streszczenie treści zawartej na stronie nr. 4

For Hammer Drilling (Percussion + Rotation) Diamond convex For opening of holes in concrete, tile or mortar, twist the indicator on top of the tool so that the hammer symbol ( 1 ) is on the side with the small diamond convex. This provides hammering + rotation. For accuracy, it is advisable to drill a small pilot hole first, before using hammering + rotation. Use a bit for con- crete and masonry drilling. (Caution: Always check first to see that the switch indicator is set to the "F

Streszczenie treści zawartej na stronie nr. 5

0 When Holes Become Clogged Should be holes you drill become clogged or dust, do not apply more with chips pressure. Instead, run the tool idle for a moment, then back out. Repeating this procedure two or three times will clean out the hole completely and then you can apply pressure once more. Fig. 6 0 Adjustable Depth Rod The adjustable depth rod is used to drill holes of uniform depth. Loosen the screw, set to desired position, then tighten the screw. Fig. 7 5

Streszczenie treści zawartej na stronie nr. 6

MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection and maintenance. The carbon brushes wear out after about 100 hours of operation. To maintain product SAFETY and RELIABILITY, repairs, maintenance and adjustment including brush inspection and replacement should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 0 Sharpening Bit Without 60" chamfering, a tungsten- carb

Streszczenie treści zawartej na stronie nr. 7

HAMMER DRILL lomm(%’’) Model HP1030 Note: The switch, noise suppressor, plug and other part to country. configurations may differ from country 7

Streszczenie treści zawartej na stronie nr. 8

so DESCRIPTION E 1 24 2 1 2 I 25 I 3 1 26 1 4 1 27 2 1 28 1 5 6 I 29 7 1 30 2 2 31 1 8 32 1 9 1 10 1 33 1 11 1 35 6 2 1 36 13 1 31 1 1, 1 1 38 17 2 39 1 IB 1 403 1 19 1 md 1 XI 405 1 21 1 406 1 22 1 23 1 - - - - MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of o