Streszczenie treści zawartej na stronie nr. 1
OM-228 322A 2006 −06
Processes
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
(Gas- And Self-Shielded)
Description
Wire Feeder
D-75S, D-75D
File: MIG (GMAW)
Visit our website at
www.MillerWelds.com
Streszczenie treści zawartej na stronie nr. 2
From Miller to You Thank you and congratulations on choosing Miller. Now you can get the job done and get it done right. We know you don’t have time to do it any other way. That’s why when Niels Miller first started building arc welders in 1929, he made sure his products offered long-lasting value and superior quality. Like you, his customers couldn’t afford anything less. Miller products had to be more than the best they could be. They had to be the best you could buy. Today, the people that bu
Streszczenie treści zawartej na stronie nr. 3
TABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-3. Additional Symbols For Insta
Streszczenie treści zawartej na stronie nr. 4
Declaration of Conformity for European Community (CE) Products This information is provided for units with CE certification (see rating label on unit). NOTE Manufacturer: European Contact: Miller Electric Mg. Co. Mr. Danilo Fedolfi, 1635 W. Spencer St. Managing Director Appleton, WI 54914 USA ITW Welding Products Italy S.r.l. Phone: (920) 734-9821 Via Privata Iseo 6/E 20098 San Giuliano Milanese, Italy Phone: 39(02)98290-1 Fax: 39(02)98290203 European Contact Signature: Declares that the produ
Streszczenie treści zawartej na stronie nr. 5
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _3/05 Warning: Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage Means Warning! Watch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. This group of symbols means Warning! Watch Out! possible Marks a special safety message. ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessa
Streszczenie treści zawartej na stronie nr. 6
ARC RAYS can burn eyes and skin. BUILDUP OF GAS can injure or kill. Shut off shielding gas supply when not in use. Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays Always ventilate confined spaces or use that can burn eyes and skin. Sparks fly off from the approved air-supplied respirator. weld. Wear an approved welding helmet fitted with a proper shade of fil- ter lenses to protect your face and eyes when welding or watching HOT PART
Streszczenie treści zawartej na stronie nr. 7
1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. MOVING PARTS can cause injury. Do not install or place unit on, over, or near Keep away from moving parts such as fans. combustible surfaces. Keep all doors, panels, covers, and guards Do not install unit near flammables. closed and securely in place. Have only qualified persons remove doors, Do not overload building wiring − be sure power supply system is panels, covers, or guards for main
Streszczenie treści zawartej na stronie nr. 8
1-5. Principal Safety Standards Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1, Boulevard, Rexdale, Ontario, Canada M9W 1R3 (phone: from Global Engineering Documents (phone: 1-877-413-5184, website: 800 −463 −6727 or in Toronto 416 −747 −4044, website: www.csa −in- www.global.ihs.com). ternational.org). Practice For Occupational And Educational Eye And Face Protection, Recommended Safe Practices for the Preparation for Welding and Cut- ANSI Standard Z87.1, from American Na
Streszczenie treści zawartej na stronie nr. 9
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION som _3/05 Avertissement : se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes. 2-1. Symboles utilisés Symbole graphique d’avertissement ! Attention ! Cette pro- cédure comporte des risques possibles ! Les dangers éven- tuels sont représentés par les symboles graphiques joints. Ce groupe de symboles signifie Avertissement ! Attention ! Risques Indique un message de sécurité particulier d’É
Streszczenie treści zawartej na stronie nr. 10
LES RAYONS D’ARC peuvent entraî- LES ACCUMULATIONS DE GAZ ner des brûlures aux yeux et à la peau. risquent de provoquer des blessures Le rayonnement de l’arc du procédé de soudage ou même la mort. génère des rayons visibles et invisibles intenses Fermer l’alimentation du gaz protecteur en cas (ultraviolets et infrarouges) susceptibles de provo- de non-utilisation. quer des brûlures dans les yeux et sur la peau. Des étincelles sont projetées pendant le soudage. Veiller toujours à bien aérer l
Streszczenie treści zawartej na stronie nr. 11
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance Risque D’INCENDIE OU D’EXPLO- DES ORGANES MOBILES peuvent SION. provoquer des blessures. Ne pas placer l’appareil sur, au-dessus ou S’abstenir de toucher des organes mobiles tels à proximité de surfaces inflammables. que des ventilateurs. Ne pas installer l’appareil à proximité de Maintenir fermés et verrouillés les portes, produits inflammables. panneaux, recouvrements et dispositifs de pro
Streszczenie treści zawartej na stronie nr. 12
2-5. Principales normes de sécurité Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1, Boulevard, Rexdale, Ontario, Canada M9W 1R3 (téléphone : de Global Engineering Documents (téléphone : 1-877-413-5184, site In- 800-463-6727 ou à Toronto 416-747-4044, site Internet : ternet : www.global.ihs.com). www.csa-international.org). Practice For Occupational And Educational Eye And Face Protection, Recommended Safe Practices for the Preparation for Welding and Cut- ANSI Standard Z87
Streszczenie treści zawartej na stronie nr. 13
SECTION 3 − DEFINITIONS 3-1. Warning Label Definitions A. Warning! Watch Out! There are possible hazards as shown by the symbols. B. Drive rolls can injure fingers. AB C C. Welding wire and drive parts are at welding voltage during operation − keep hands and metal objects clear. 1 Electric shock can kill. 1.1 Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves. 1.2 Protect yourself from electric shock by insulating yourself 1 1.1 1.2 1.3 from work
Streszczenie treści zawartej na stronie nr. 14
3-2. WEEE Label Do not discard this product with general waste. Reuse or recycle Waste Electrical and Electronic Equipment (WEEE) by disposing at a designated collec- tion facility. Contact your local recycling office or your local distributor for further information. 3-3. Rating Label For CE Products For label location see Section 5-3. S/N: 24 V 1 50/60 Hz U 1 IP 21 = 10.0 = A 50/60 I 1 100 V 750 A X 100 % U I = 2 2 = ST-178 794-A 3-4. Symbols And Definitions Some symbols are found only on CE
Streszczenie treści zawartej na stronie nr. 15
SECTION 4 − INTRODUCTION 4-1. Specifications Welding Wire Type of Input Welding Power IP Overall Maximum Wire Feed Circuit Diameter Weight Power Source Type Rating Dimensions Spool Weight Speed Range Rating Range 24 Volts ac Constant 100 Volts, IP 21 Length: 35 in 60 lb Standard .023 to 5/64 in 83 lb Single-Phase Voltage (CV) 750 Amperes, (889 mm) (27 kg) Speed: 50 to (0.6 to 2.0 (37.6 kg) 10 Amperes DC With 14-Pin, 100% Duty Width: 21.5 in 1400 ipm (1.3 mm) 50/60 Hertz that Provides Cycle (546
Streszczenie treści zawartej na stronie nr. 16
5-2. Equipment Connection Diagrams 1 Welding Power Source 2 Contactor Control/Power Cord 3 Weld Cable 4 Weld Cable 5 Workpiece 6 Welding Gun 7 Wire Feeder 8 Gas Hose 9 Gas Cylinder and Regulator (Customer Supplied) Shielding gas pressure not to exceed 100 PSI (689 kPa). 1 9 2 3 4 5 8 7 6 804 564-B OM-228 322 Page 12
Streszczenie treści zawartej na stronie nr. 17
5-3. Rear Panel Connections And Rotating Drive Assembly 7 2 4 1 3 5 6 Connection Connection Point A Point B Tools Needed: 9/16, 5/8 in 804 557-B / 804 184-B Left Side Shown 1 14-Pin Control Cable - 10 Ft (3.0 m) 4 Weld Cable If welding at 350 amps or more, con- 2 Shielding Gas Valve Fittings nect jumper weld cable to connection Connect weld cable to connection point A point A. Route cable around front of on right side of drive assembly. Requires fitting with 5/8-18 right-hand feeder. threads
Streszczenie treści zawartej na stronie nr. 18
5-4. 14-Pin Plug Information Pin* Pin Information A 24 volts ac with respect to socket G. B Contact closure to A completes 24 volts ac contactor control circuit. J J A A K K I B G Circuit common for 24 volts ac circuit. L L H N C C +10 volts dc input from power source to wire feeder with respect to socket D. M M G G D D D Remote control circuit common. F F E E E 0 to +10 volts dc output signal from wire feeder to power source with respect to socket D. H Voltage feedback; 0 to +10 volts dc, 1 vol
Streszczenie treści zawartej na stronie nr. 19
5-8. Installing PD Continuous Wire Guides PD Continuous Wire Guides: Should be used with .068/.072 in (1.8 mm) and smaller diameter wire for opti- mal performance. Should be used with PD drive rolls and cannot be used with non-PD (old-style) drive rolls. 70 series wire guides are not compatible with 75 series wire 3 feeders. 1 Pressure Door Assembly 2 PD Inlet Guide 3 PD Wire Guide (Hard Wire) 4 PD Wire Guide (Two Pieces interlocked for Aluminum 4 Wire) Installing PD continuous wire guides w
Streszczenie treści zawartej na stronie nr. 20
5-9. Installing Non-PD (Old Style) Wire Guides Installing wire guides with non- PD (old-style) drive rolls Non-PD (old-style) wire guides and drive rolls should be used with 5/64 in (2.0 mm) and larger diameter wire. 1 Pressure Door Assembly 2 PD Inlet Guide 3 Intermediate Guide 5 4 Set Screw 2 5 Guide Holder 6 Exit Guide 6 3 Open pressure door assembly. Lift up drive roll swing arms. 4 Install PD inlet guide. Do not tighten set screw to se- cure inlet guide. Set screw may be used to se- c
