Streszczenie treści zawartej na stronie nr. 1
TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
SR-M8102
CD-R/CD-RW DRIVE
USER MANUAL
Streszczenie treści zawartej na stronie nr. 2
CONTENTS Introduction..............................................................................1 Setup ........................................................................................3 Using the CD-R/CD-RW Drive .................................................6 Troubleshooting.......................................................................9 Specifications ........................................................................10 Drive Connectors......................
Streszczenie treści zawartej na stronie nr. 3
INTRODUCTION – SR-M8102 General Features CD-R/CD-RW disc write/rewrite at 52X/32X 3-way Disc Eject (eject button, software, emergency eject hole) Average Random Access Time CD 110ms CD-RW 120ms Horizontal or Vertical Mount 2MByte Buffer Playback interchangeability for CD-ROM discs BUS Interface - ATAPI Formats Compatibility CD-DA (Red Book) - Standard Audio CD & CD-TEXT CD-ROM (Yellow Book Mode 1&2) - Standard Data CD-ROM XA (Mode 2 Form 1&2) - Photo CD, Multi Sessi
Streszczenie treści zawartej na stronie nr. 4
Front Panel Figure 1.SR-M8102 CD-R/RW Drive Front Panel Loading Load disc using tray. Tray The LED lights when the drive is operating LED Load/Unload The Load/Unload button is used to open the disc tray so you can install or remove a disc. Button The emergency eject hole is to be used only when the Loading Tray will not open Emergency Eject Hole when Eject button is pressed.
Streszczenie treści zawartej na stronie nr. 5
SETUP – SR-M8102 The following steps must be performed to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the CD-R/CD-RW drive. By placing a jumper on the pins, you can select the following functions: CS Drive is configured using host interface signal CSEL SL Configures drive as Slave MA Conf
Streszczenie treści zawartej na stronie nr. 6
Placing CD-R/CD-RW Drive inside your Computer Now that you have set the jumpers, you are ready to install your CD-R/CD-RW drive inside your computer. Important Note: Disconnect power from your computer system before beginning installation. Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. If the CD-R/CD-RW drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system. Your Toshiba CD-R/CD-RW drive
Streszczenie treści zawartej na stronie nr. 7
Power Cable - Connect an internal computer power supply cable to the power socket at the back of the CD- R/CD-RW drive. One side of the plug has chamfered edges, so the power connector fits only one way. Push plug completely into the socket making sure the plug fits correctly. Figure 4.Installing Power Cable Audio Cable (optional) - If you have a sound card and speakers, and would like to play audio CDs on your computer, you will need to install a CD/DVD audio cable. Toshiba'
Streszczenie treści zawartej na stronie nr. 8
USING THE CD-R/CD-RW Drive – SR-M8102 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's Loading tray by pressing the Eject Button. 2. Place disc or into drive's Loading tray 3. Press Eject button again or gently push on the open disc tray. Tray will automatically close. Inserting a Disc - Vertically To insert a disc in a drive that is mounted vert
Streszczenie treści zawartej na stronie nr. 9
Figure 2.Inserting Disc Vertically Removing a Disc To remove a disc from the CD-R/CD-RW drive, perform the following steps: 1. Open the Loading Tray by pressing the Eject Button. 2. Slide disc holders away from disc. 3. Grasp disc by edges, and lift out of loading tray. 4. Press Eject Button again to close Loading Tray. CD-RW Software Additional software is required to use the SR-M8102 CD-R/-RW functions Usage Guidelines • Keep the disc tray closed when not using the CD-R/CD-
Streszczenie treści zawartej na stronie nr. 10
Figure 3.Using Emergency Eject Cleaning Media Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc accessing speed. If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather from the inner side outward. 8
Streszczenie treści zawartej na stronie nr. 11
TROUBLESHOOTING – SR-M8102 Problem Solution Disc tray cannot be opened • Check that there is power to drive. • Use Emergency Eject instructions to open tray. Drive is not recognized by system • Is the drive connected properly? Are all cables plugged in properly (e.g. Power Cable, Interface Cable and Audio Cables). • Are the drive configuration jumpers on the CD-R/CD-RW drive set properly? • Is the software driver loaded? On a step-by-step (F8) Boot of the system is the CD-R/
Streszczenie treści zawartej na stronie nr. 12
SPECIFICATIONS –SR-M8102 General Interface ATAPI Format for Writing: Disc at once, Track at once, Session at once, Variable & Fixed Packet write Format Compatibility: CD-DA (Red Book) - Standard Audio CD & CD-TEXT CD-ROM (Yellow Book Mode 1&2) - Standard Data CD-ROM XA (Mode 2 Form 1&2) - Photo CD, Multi Session CD-I/FMV (Green Book, Mode 2 Form 1&2, Ready, Bridge) CD-Extra/CD-Plus (Blue Book) - Audio & Text/Video Video-CD (White Book)- MPEG1 Video CD-R (Orange Book Part I
Streszczenie treści zawartej na stronie nr. 13
Transfer Rate CD-ROM Read (Mode 1) 7,800KB/second CD-R/RW Read (Mode 1) 6,000KB/second Random Access Time 110ms CD-ROM 120ms CD-RW Data Buffer 2MB Environmental Ambient Temperature Operating 5° to 45° C (41° to 113° F) Storage -25° to 60° C (13° to 140° F) Relative Humidity Operating 10% to 80% Storage/Shipping 10% to 95% Vibration Operating (Random) 0.5Grms 15min Non-operating (10 to 500Hz) 0.712Grms 15min Shock Operating (Read) 11 msec 6G, 2msec 60G Oper
Streszczenie treści zawartej na stronie nr. 14
Connectors DC input 4-pin Power Supply Connector ATAPI Interface Connector 40 Pin I/F ATAPI Standard Audio Connectors 4-pin and 2-pin connector (use matching housing, Part No. 70066, made by Molex Corp, or equivalent) Regulatory The SR-M8102 CD-R/RW has been certified by the following regulatory agencies • UL 1950 • CSA C22.2 No. 950 • TUV (EN60950I) • CE standard • DHHS 21 CFR Sub-Chapter J • FDA CFR21, EN60825 12
Streszczenie treści zawartej na stronie nr. 15
DRIVE CONNECTORS –SR-M8102 Figure 1.SR-M8102 CD-R/CD-RW Drive Rear Panel - Connectors Power Power is supplied to your CD-R/RW drive by the connection with your computer's +5V/+12V power cable to the power socket at the back of drive. One side of the plug has Connector chamfered edges, so the power connector fits only one way. CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in upside-down with power ON. Supplies Analog and Digital sound to
Streszczenie treści zawartej na stronie nr. 16
Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN I/O SIGNAL HOST SIGNAL NAME PIN I/O SIGNAL HOST SIGNAL NAME NO. NAME NO. NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 - GND 3 I/O HD7 Host Data Bus BIT 7 23 I HWR-,STOP Host I/O Write 4 I/O HD8 Host Data Bus BIT 8 24 - GND 5 I/O HD6 Host Data Bus BIT 6 25 I HRD-, Host I/O Read HDMARDY, - HSTROBE 6 I/O HD9 Host Data Bus BIT 9 26 - GND 7 I/O HD5 Host Data Bus BIT 5 27 O IORDY, I/O Channel Ready
