Streszczenie treści zawartej na stronie nr. 1
Thunder i7505 S2665
///
Revision 1.02
Copyright © TYAN Computer Corporation, 2002. All rights reserved. No part of this manual may be
reproduced or translated without prior written consent from TYAN Computer Corp.
All registered and unregistered trademarks and company names contained in this manual are
property of their respective owners including, but not limited to the following.
TYAN, Thunder i7505 S2665 are trademarks of TYAN Computer Corporation.
Intel, Xeon, and co
Streszczenie treści zawartej na stronie nr. 2
Table of Contents Before you begin… ………………………………….Page 3 Chapter 1: Introduction ………………………………….Page 4 1.1 Congratulations ………………………………….Page 4 1.2 Hardware Specifications ………………………………….Page 4 Chapter 2: Board Installation ………………………………….Page 6 2.0 Board Image ………………………………….Page 7 2.1 Board Parts, Jumpers and Connectors ………………………………….Page 8 2.2 Jumper and Connector Settings ………………………………….Page 9 2.3 AUX Audio and CD Audio Connector ………………………………..Page 10
Streszczenie treści zawartej na stronie nr. 3
Check the box contents! The retail motherboard package should contain the following: 1x Thunder i7505 S2665 1x 34-Pin floppy drive cable 1x Ultra160/320 LVD SCSI cable (if optional SCSI included) 1x Ultra-DMA-100/66/33 IDE cable 1x Thunder i7505 S2665 User’s Manual 1x TYAN driver CD 1x Adaptec Ultra160/Ultra320 SCSI driver diskette (if optional SCSI included) 1x I/O shield 2X CPU retention If any of these items are missing, please contact your vendor/dea
Streszczenie treści zawartej na stronie nr. 4
Chapter 1: Introduction 1.1 – Congratulations! You are now the owner of one of the most advanced dual Intel Xeon processor solutions available: the Thunder i7505 S2665. Based on Intel's E7505 chipset, the Thunder i7505 S2665 is Hyper-Threading ready - utilizing onboard resources so that many data threads can be handled with ease by two processors. With a 8x/4x AGP slot, six USB 2.0 and 1.1 compatible ports, two FireWire (IEEE-1394) ports, four DDR DIMM sockets, a Gigabit Ethernet
Streszczenie treści zawartej na stronie nr. 5
Integrated PCI IDE Form Factor § Provides two PCI bus master channels for § SSI EEB v3.0 footprint (12" x 13") up to four Enhanced IDE devices § 8-layer design § Supports for UDMA 33/66/100 IDE drives § EPS12V with WS 6-pin power connectors and ATAPI compliant devices § Stacked PS/2 keyboard and mouse ports § Supports up to four Enhanced IDE devices § Stacked four USB2.0/1.1 ports § Stacked one serial port and one parallel port Integrated I/O § One RJ45 LAN port with LEDs § One IEE
Streszczenie treści zawartej na stronie nr. 6
Chapter 2: Board Installation Installation You are now ready to install your motherboard. The mounting hole pattern of the Thunder i7505 S2665 matches the EEB V3.0 specification. Before continuing with installation, confirm that your chassis supports a standard EEB V3.0 motherboard. How to install our products right….the first time! The first thing you should do is read this user’s manual. It contains important information that will make configuration and setup much easier. Here a
Streszczenie treści zawartej na stronie nr. 7
2.0 – Board The following is an image of the S2665. This picture is representative of the latest board revision available at the time of publishing. The board you receive may or may not look exactly like the above picture. The following page includes details on the vital components of this motherboard. 7 http://www.TYAN.com
Streszczenie treści zawartej na stronie nr. 8
2.1 – Board Parts, Jumpers and Connectors This diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram. Jumper Legend Jumper OFF without jumper cover Jumper ON with jumper cover To indicate where the location of pin-1 To indicate where the location of pin-1 8 http://www.TYAN.com
Streszczenie treści zawartej na stronie nr. 9
2.2 – Jumper and Connector Settings Jumper / Function Settings Connector J8 AUX Audio Connector Enable/Disable Onboard Intel Open: Enable (Default) J10 82540EM GbE NIC Close: Disable J11 Fan Connector Close Pin-1 and Pin-2 (Default) Disable PS/2 devices’ ACPI wake up function J12 PS/2 ACPI Jumper Close Pin-2 and Pin-3 Enable PS/2 devices’ ACPI wake up function Close Pin-1 and Pin-2 (Default) Disable rear panel USB devices’ ACPI wake up function J14 Rear Panel USB ACPI
Streszczenie treści zawartej na stronie nr. 10
2.3 – AUX Audio Connect or (J8) and CD Audio Connector (J16) J 8 (AUX Audio connector) Connects to internal audio sources such as TV tuner, MPEG, or other similar cards J16 (CD Audio connector) Connects to a CD-ROM drive via an optional CD audio cable 2.4 – Ena ble/Disable Onboard LAN Jumper (J10) OPEN (Default) To enable onboard LAN CLOSE To disable onboard LAN 2.5 – Fan Connectors (J11, J19, J22, J32, J38, J55 and J60) Use these headers to
Streszczenie treści zawartej na stronie nr. 11
2.6 – PS/2 ACPI Jumper (J12) pin-3 CLOSE Pins 1 and 2 (Default) To disable PS/2 devices’ ACPI wake up function pin-3 CLOSE Pins 2 and 3 To enable PS/2 devices’ ACPI wake up function 2.7 – Rear Panel USB ACPI Jumper (J14) pin-3 CLOSE Pins 1 and 2 (Default) To disable rear panel USB devices’ ACPI S3/S4/S5 wake up function pin-3 CLOSE Pins 2 and 3 To enable rear panel USB devices’ ACPI S3/S4/S5 wake up function Total current of all USB devices should not exceed t
Streszczenie treści zawartej na stronie nr. 12
2.9 – Disable Slot-B and Slot-C PCI-X Capability Jumper (J31) OPEN (Default) To enable PCI-X capability on Slot-B and Slot-C CLOSE To disable PCI-X capability on Slot-B and Slot-C Onboard SCSI chip PCI-X capability will be disabled due to sharing of the same bus 2.10– Clear CMOS Jumper (J50) Clear Default You can reset the CMOS settings by using this jumper when you § Have forgotten your system/setup password § Need to clear system BIOS setting - Power
Streszczenie treści zawartej na stronie nr. 13
2.12 – IEEE 1394 Connector (J66) Connects to a 1394 device via an optional 1394 cable 2.13 – LCD Connector (J69) Connects to a LCD display via an optional cable 2.14 – Front Panel Audio Connector (J71) Signal Pin Pin Signal Description # # Description Micro input 1 2 Analog GND Micro bias 3 4 Analog VCC Right line Right line 5 6 output return NC 7 8 Key Left line Left line 9 10 output return 2.15 – Chassis Intrusion Connector (J72) 13 http://www.TYAN.c
Streszczenie treści zawartej na stronie nr. 14
Pin-1 Intrusion cable detection (low asserted) Pin-2 Intrusion detection (low asserted) Pin-3 GND 2.16 – Front Panel USB Header (J73) Signal Pin Pin Signal Description # # Description VCC 1 2 VCC Channel E Channel F 3 4 Data negative Data negative Channel E Channel F 5 6 Data positive Data positive GND 7 8 GND Not Key 9 10 connected 14 http://www.TYAN.com
Streszczenie treści zawartej na stronie nr. 15
2.17 – Front Panel Connector (J74) Signal Description Pin # Pin # Signal Description 1 2 Sleep LED “— “ Speaker “— “ Sleep LED “+ “ 3 4 Key Key 5 6 GND 7 8 Power LED “+ “ Speaker “+ “ 9 10 Key Power LED “+ “ GND 11 12 Key 13 14 Key Message LED “+ “ 15 16 Not connected Message LED “— “ Key 17 18 SCSI LED Input HD LED “+ “ 19 20 SCSI LED Input HD LED “— “ 21 22 Not connected GND 23 24 Key Power Button 25 26 GND Sleep Button 27 28 GND Reset Button 29 30 GND 2.18
Streszczenie treści zawartej na stronie nr. 16
2.20 – Mounting the Motherboard Before installing your motherboard, make sure your chassis has the necessary motherboard support studs installed. These studs are usually manufacturer pre-installed, metal and are gold in color. If you are unsure of stud placement, lay the motherboard inside the chassis and align the studs. NOTE YOU MUST make sure that there are no studs where there are no screw holes. 2.21 – Installing the Memory Before attempting to install any memory, here
Streszczenie treści zawartej na stronie nr. 17
Make sure that the memory you have is compatible with the motherboard as well as the processor. For example, DDR200 and DDR266 memory modules can be used for FSB=400MHz Intel Xeon processor but only DDR266 memory modules can be used for FSB=533MHz Intel Xeon processor. DDR200 (PC1600) DDR266 (PC2100) v v Xeon FSB=400MHz supported supported X v Xeon FSB=533MHz unsupported supported Memory Installation Procedure When installing memory modules, make sure the modules a
Streszczenie treści zawartej na stronie nr. 18
2.22 – Installing the Processor(s) and Heatsink(s) Your Thunder i7505 S2665 supports the latest processor technologies from Intel. Check the following page on TYAN’s website http://www.tyan.com for latest processor support: The following diagrams will detail how to install your processor(s): Only identical CPUs can be used. REMINDER When installing only 1 processor, ensure to install it in CPU socket 1 . (see page-8) The processors you choose to use may not look exactly li
Streszczenie treści zawartej na stronie nr. 19
The following diagram will illustrate how to install the most common heatsinks: a. Align the heatsink mounting bracket to the holes around the processor socket b. Insert Black securing peg into bracket holes c. Insert White locking peg into Black securing peg d. Repeat process to mount all other brackets e. Seat heatsink between brackets on the processor f. Attach heatsink clips 19 http://www.TYAN.com
Streszczenie treści zawartej na stronie nr. 20
Finishing Installing the Heatsink After you finish installing the heatsink onto the processor and socket, attach the end wire of the fan (which should already be attached to the heatsink) to the motherboard. The following diagram illustrates how to connect fans onto the motherboard. After you have finished installing all the fans you can connect your drives (hard drives, CD -ROM drives, etc.) to your motherboard. 2.23 – Installing Add- In Cards Before installing add-in cards, it
