Streszczenie treści zawartej na stronie nr. 1
MULTI-PURPOSE LCD DISPLAY
MU-150C
Streszczenie treści zawartej na stronie nr. 2
Streszczenie treści zawartej na stronie nr. 3
SAFETY INSTRUCTIONS Safety Instructions for the Operator Safety Instructions for the Installer WARNING WARNING Do not open the equipment. Do not open the cover unless totally familiar with Only qualified personnel electrical circuits and should work inside service manual. the equipment.
Streszczenie treści zawartej na stronie nr. 4
TABLE OF CONTENTS FOREWORD ........................................................................................................ iii SYSTEM CONFIGURATION................................................................................ iv EQUIPMENT LISTS .............................................................................................. v 1 MOUNTING ...................................................................................................... 1 1.1 Display Unit......
Streszczenie treści zawartej na stronie nr. 5
FOREWORD A Word to the Owner of the MU-150C FURUNO Electric Company thanks you for purchasing the MU-150C 15” Multi-Purpose LCD Display. We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by our extensive global network of agents and dealers. Your equipment
Streszczenie treści zawartej na stronie nr. 6
SYSTEM CONFIGURATION RGB Radar, Video Plotter, Navigator, Video Sounder, Scanning Sonar, etc. 24 VDC or Control unit of 100 - 240 VAC Video Sounder (e.g., FCV-1200 series) NMEA 0183 Navigator (GPS, etc.)* * = When using the FCV-1200 series or CH-250, NMEA 0183 data may be output to the MU-150C instead of the interface unit. Connectable equipment MU-150C Display Unit Type Equipment Landscape Portrait* FR-1500 MK3 series Yes No FCV-1200 series Yes Yes (Modification required) FCV-150
Streszczenie treści zawartej na stronie nr. 7
EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks AC specification Display Unit MU-150C − 1 DC specification SP10-02801 001-414-460 For DC Spare Parts * 1 set SP10-02802 001-414-970 For AC For AC (CP10-04901) CP10-04910 001-414-690 Installation Materials * 1 set CP10-04920 001-414-700 For DC (CP10-04902) FP10-02501 001-414-490 1 set Accessories * FP10-05401 001-402-540 1 For FCV-1500L Bracket * FP10-02510 001-414-510 1 Including FP10-02511 Option Name Type
Streszczenie treści zawartej na stronie nr. 8
1 MOUNTING Refer to the outline drawing at the end of the manual for mounting dimensions. Note: The LCD is made of glass. Handle it with care. 1.1 Display Unit The display unit may be flush mounted in a panel or on a desktop, using the optional bracket. Display tilt can be chosen from 9° or 20°, by the location of the mounting plate. When selecting a mounting location, keep in mind the following points: • Locate the unit out of direct sunlight. • Select a location where the di
Streszczenie treści zawartej na stronie nr. 9
384 0.5 366 1 15 0.5 See Note 2. Cover Display Unit Display unit and cover 3. Fasten the display unit to the mounting location with six tapping screws (5X30). Note 1: Hex head bolts may also be used to fasten the display unit. However, their length must be at least 30 mm. Note 2: Use M5 bolt or tapping screw (nominal diameter: M5), although the size of the mounting holes in the display unit is M8. 384 – 0.5 333 – 0.5 366 – 1 315 – 1 15 – 0.
Streszczenie treści zawartej na stronie nr. 10
Desktop mounting The display unit can be mounted on a desktop, using the optional bracket (Type: FP10-02510, Code No.: 001-414-510). 1. Fasten the mounting base (lower) to the mounting location with four sets of hex head bolts, spring washers, flat washers and nuts. Hex Head Bolt Spring Washer Flat Washer Nut FRONT Mounting base (lower) 2. Fasten the bracket and mounting plate to the mounting base (upper) with 12 hex head bolts. Fasten the mounting plate at the rear for 9° tilt, or
Streszczenie treści zawartej na stronie nr. 11
3. Loosely screw six screws (M5X15) into the holes at the rear of the display unit. Set the screws on the display unit to the holes on the bracket and then tighten the screws. (Note that the display unit may also be mounted in portrait orientation.) Fastening the front panel 4. Fasten the power cable (local supply in case of AC power), cable from the control and operation sections of external equipment and ground wire (local supply) at the rear of the MU-150C. For use of the cable type
Streszczenie treści zawartej na stronie nr. 12
5. Grease the two hex head bolts for fastening the display unit to the mounting base (lower). 6. Fasten the display unit to the mounting base (lower) with the two hex head bolts greased at step 5. Hex Head Bolt Fastening the mounting base (lower) to the display unit 7. For portrait orientation, attach logo (supplied) at upper left hand corner. 5
Streszczenie treści zawartej na stronie nr. 13
1.1.1 Hood (option) A hood (portrait or landscape) is optionally available. Attach it to the display unit with Velcro tape as shown below. 1. Attach nine sets of Velcro tape to the display unit at the locations shown below, in as straight as possible. Attach Attach in line. in line. Display unit, how to attach Velcro tapes 2. Attach the hood to the display unit. 6
Streszczenie treści zawartej na stronie nr. 14
2 WIRING 2.1 Wiring External Equipment Connect external equipment to the MU-150C by referring to the drawings in this section. A cable with connector at both ends is provided to connect equipment. General-purpose monitor To use the MU-150C as a general-purpose monitor, connect equipment with a mini D-SUB 15P connector. In this case do not connect a navigator to the NMEA port. Nav data is output through the D-SUB 25P connector. CH-37: DISPLAY CH-250: INTERFACE UNIT RGB OUT FCV-120
Streszczenie treści zawartej na stronie nr. 15
Connecting FCV-1200 series and CH-250 Using the cables designated below (or equivalent) to connect the FCV-1200 series or CH-250 makes their interface unit of the FCV-1200 series and CH-250 unnecessary. The mini D-SUB 15 P connector cannot be used to connect the FCV-1200 series and CH-250. Navigator, etc. 06S4078 FCV-1200 Series: 24 VDC PROCESSOR UNIT CN1 or 100-240 VAC CH-250: TRANSCEIVER UNIT Ground DATA/VIDEO OUT Terminal FCV-1200 Series: CONTROL UNIT MJ-A10SPF0002-01
Streszczenie treści zawartej na stronie nr. 16
• Cable 06S4078 is of waterproof construction, however, the MU-150C is not waterproof (specification IPX0). Therefore, remove rubber cover and fixing metal from the display side of the cable. Remove fixing metal. Remove rubber cover. D-sub connector 9
Streszczenie treści zawartej na stronie nr. 17
3 ADJUSTMENTS Controls for adjustment of the picture are provided on the rear of the display unit. Open the small cover to access the controls. 12 3 GND 100-240 VAC POWER 2A 50-60 Hz S1 S2 S3 S4 R1 J16 EXTBRILL S1 SEL J17 BRILL S2 UP R2 J18 BRTP J16 J17 J18 S3 DOWN R1 R S4 RESET 131313 R2 G R3 R3 B DATA/VIDEO IN NMEA CONT Rear panel (AC type) 10
Streszczenie treści zawartej na stronie nr. 18
3.1 Picture Adjustment Contrast and picture are adjusted with [S1]: Opens menu; selects menu items. [S2]: Increases setting. [S3]: Decreases setting. [S4]: Initializes setting. Note: Though “EXIT” is printed on the CONE Board (10P6877), the function of S4 switch is “RESET.” [S1] Brilliance (Not used.) [S1] Contrast [S1] Size (horizontal size for landscape type, vertical size for portrait type) [S1] Geometry [S1] Center (vertical position for landscape type, horizontal position f
Streszczenie treści zawartej na stronie nr. 19
3.2 RGB Adjustment Color may be adjusted with the following potentiometers. Turn the potentiometers clockwise to increase color. Model Potentiometer Setting FCV-1200 Series, CH-250, Default setting FR-1760DS GD/GP-280/380/680, FCV-1500 Fully clockwise Series, CH-37, CSH23/73/83, FR-1500 MK3 Series R1: Red R2: Green R3: Blue 3.3 Brilliance Adjustment Brilliance can be adjusted from the control unit of the FCV-1200 series or CH-250 by setting jumper block J17 as below. J17:
Streszczenie treści zawartej na stronie nr. 20
4 OPERATION FURUNO LED BRILLIANCE Control POWER Switch Display unit POWER switch: Turns the power on/off. The LED lamp lights in green when the unit is turned on and goes off when the unit is turned off. To turn the MU-150C on and off from the control unit of a video sounder such as the FCV-1200 series, turn on the POWER switch of the MU-150C. Note that with the MU-150C turned on and the FCV-1200 turned off the LED on the MU-150C lights in red. This means that weak current is flowi
