Streszczenie treści zawartej na stronie nr. 1
PLVWR70IR
OWNER’S MANUAL
FLIP DOWN TFT MONITOR
Streszczenie treści zawartej na stronie nr. 2
INSTALLATION Desk-top Installation Mounting Bolts (M3x6) 2 1 Tapping Screw (M4x10) Bracket Levers Fig. 1 1. Determine the mounting location and drill four mounting holes. 2. Attach the bracket to the holes with the tapping screws (M4x10). 3. Let the two levers aim at the fixing holes on the bottom of the base to fix the display unit. 4. Attach the TV unit to the preferred location with the mounting bolts (M3x6). 5. For the convenience of fixing the unit, you can turn the display left or right to
Streszczenie treści zawartej na stronie nr. 3
INSTALLATION Ceiling-on Installation Fig. 2 Bracket Levers Tapping Screws (M4x10) Fixing holes Mounting Bolts (M3x6) Fig. 3 1. Determine the mounting location and drill four mounting holes (see Fig.2). 2. Attach the bracket to the holes with the tapping screws (M4x10). 3. Let the two levers aim at the fixing holes to fix the display unit. 4. Attach the unit to the bracket with the mounting bolts (M3x6). 5. When the installation has completed, you can also turn the display upward or downward, le
Streszczenie treści zawartej na stronie nr. 4
REPLACING THE CAR DOME LAMP Follow the directions show below for a new lamp changing. 1. Position light switch to “ ”. 2. Push back the lamp cover and open it. (Refer to the following figure) 3. Remove and discard the old lamp. 4. Install a new bulb. 5. Close the cover. Lamp Cover Bulb Light Switch Bulb Specification Diameter: ø8mm Length: 28mm Voltage Spec.: DC12V, 5W CAR DOME LAMP WIRING Line for Car Dome Lamp Note: Color Connection Red Power Supply White Interior Lig
Streszczenie treści zawartej na stronie nr. 5
CONTROL & FUNCTION KEYS 1 2 4 5 21 6 3 7 8 13 9 3 11 11 12 12 14 18 15 16 20 17 10 7” INCH TFT COLOR MONITOR 5
Streszczenie treści zawartej na stronie nr. 6
MONITOR 1. & 2. (POWER) and POWER INDICATOR LIGHT When the unit is provided DC 12V power, press POWER button (1) to turn on the unit. And then the power indicator light (2) will be illuminated red. Press it again to turn it off. 3. CAR DOME LAMP The two car dome lamps (3) will be on in some needed situations. 4. LIGHT SWITCH There are three settings for the car dome lamp operation: (OFF), (AUTO), and (ON), refer to light switch (4). A. To turn off the lamp. B. To make the lamp turned on onl
Streszczenie treści zawartej na stronie nr. 7
13. PUSH (Monitor Release Button) Opening the Monitor Press the PUSH button (13) to eject the screen display from the base at a little angle. Then you can easily turn the display upward or downward for good viewing. The monitor also can be adjusted through 30 degree both left and right from the central viewing position Closing the Monitor Return the monitor to the central viewing position. Then push the monitor back into the monitor base unit until the screen engages with PUSH button (13) .
Streszczenie treści zawartej na stronie nr. 8
OWNER’S MANUAL INFRARED HEADPHONE 8
Streszczenie treści zawartej na stronie nr. 9
INFRARED HEADPHONE This infrared headphone is supplied with the main unit that has the infrared transmitting function. The user can put on the infrared headphone within proper range to hear the sound signal emitting from the infrared transmitting window of the main unit. Operation for the headphone batteries Two Size AA (1.5V) batteries are required to operate the headphones. Rechargeable batteries with a sufficiently high voltage can be used as well. Choosing batteries with a high capacity (mAh
Streszczenie treści zawartej na stronie nr. 10
Removing the headphone batteries: To remove the batteries, open the battery lid as described above and pull the battery out of the battery compartment by pushing the battery towards the spring until the plus pole is released and slides out. ATTENTION! Never leave batteries inside the headphones for very long periods of time to prevent any damage to the headphones from leaking batteries. Dispose of spent batteries conforming to local waste disposal rules. Check the remaining power of the headphon
Streszczenie treści zawartej na stronie nr. 11
Listening to a program When the main unit is working, it will automatically transmit the audio signal, and then you can use the infrared headphone to listen to a program. 1. Set the volume control of the headphone to minimum then switch on the headphone. And then put on it. The length of the headphone’s band can be adjusted to your need. 2. Adjust the volume. Slowly increase volume level. After each use, be sure to switch off the headphone to extend battery life. ATTENTION! Listening over headph
Streszczenie treści zawartej na stronie nr. 12
www.pyleaudio.com 88-T1342-05
