Resumo do conteúdo contido na página número 1
BASIC PHONE
Model 98380
OPERATING INSTRUCTIONS
Resumo do conteúdo contido na página número 2
This Interquartz telephone has been manufactured to very high standards and is very easy to use. Please read this manual carefully to find out how to use the features. Contents 1. Important Notes ..................................................................................... 2 Intended use ........................................................................................ 2 Telephone facilities ................................................................................ 2 REN num
Resumo do conteúdo contido na página número 3
1. Important Notes Intended use This apparatus is intended for use on 2 wire analogue PSTN and PABX circuits within the United Kingdom. Declaration of Conformity Interquartz (UK) Limited declares under its sole responsibility that this product Model: BASIC PHONE 98380 XWA Is in conformity with the following relevant harmonised standards Health & Safety 73/23/EEC Electromagnetic Compatibility 89/336/EEC Following the provisions of Council Directive 1999/5/EC on radio equipment and tele
Resumo do conteúdo contido na página número 4
REN number The Ren number of this telephone is 1. If you wish to connect any other equipment to the line, simply add the REN numbers of each piece together and ensure that the total does not exceed 4. If too many phones are connected to the line, the circuit may be overloaded any your telephone may not ring. Not all telephones have the same REN. If a British Telecom phone is supplied unmarked, you can assume that it has a REN of 1 Emergency calls "999" calls can be made on this telephone, for t
Resumo do conteúdo contido na página número 5
2. Installation This telephone is designed to plug straight into a modular style socket. If you do not have one of these sockets, they can be obtained from your Network Supplier. Connection Insert the line cord into the socket. Set the tone / pulse switch to the appropriate position. If you are unsure as to whether your exchange is pulse or tone, call the Network Supplier and they will advise you. Set the ringer volume and ringer pitch control, as desired. Wall mounting Using the template s
Resumo do conteúdo contido na página número 6
1. Release 2. Insert screw driver into slot phone number plate and then pry to release HANDSET RETAINER 3. Insert the 4. HANDSET RETAINER HANDSET RETAINER for wall mount HANDSET RETAINER for wall mount Figure 3 Handset Retainer for Wall Mounting 3. Telephone Features Ringer Indicator Flashes when the telephone rings with an incoming call. Ringer Volume Switch Located on the base of the unit ( see Figure 4 ). Move switch to select no sound (OFF), muted sound (LOW) or full sound (HIGH) for ring
Resumo do conteúdo contido na página número 7
RINGER HI / LO / OFF SWITCH RINGER PITCH CONTROL TONE / PULSE SWITCH VOICE MESSAGING ( S1/ S2 / N ) SWITCH TIMED BREAK / EARTH RECALL SWITCH Figure 4 Switch Location Ringer Pitch Control Located on the base of the unit ( see Figure 4 ). Rotating this knob alters the pitch of the ringing signal. Tone / Pulse Switch Located on the base of the unit ( see Figure 4 ). Used to select the correct dialling mode, either TONE or PULSE. If you have any doubt about the system supplied to your phone, co
Resumo do conteúdo contido na página número 8
4. Operating Instructions To dial a number, lift the handset, wait for the tone and then key in the number required. Redial / Pause Function Depending on its use, this button either acts as a redial button or as a pause inserting button Redial 1. Lift handset 2. Press REDIAL / PAUSE button 3. Telephone automatically redials the last number called ( up to 32 digits) Pause The Pause command may be needed if the phone is connected to certain types of PABX or to any network where a pause is required
Resumo do conteúdo contido na página número 9
5. PABX and System Usage This telephone can be used behind a PABX or on a network system that utilises the recall function. There are many such systems and whilst it is likely that no problems will be encountered, it cannot be guaranteed that the telephone will operate correctly under all circumstances and any cases of difficulty should be referred to your supplier. Recall Before you attempt to change the recall switch ( see Figure 4 and 5 ), you should disconnect the phone from the network. S1
Resumo do conteúdo contido na página número 10
Voice messaging When used behind a PABX, this telephone will respond to voice messaging systems on many PABX types, giving a visual signal of a message waiting. Your telephone manager will be aware of which system is relevant to your organisation and will adjust or advise you on the adjustment of your telephone accordingly. This adjustment is carried out by means of a switch, labelled S1 / S2 / N, located next to the recall switch, mentioned above. As supplied, the switch is set to the N ( norma
Resumo do conteúdo contido na página número 11
Will not ring - Ringer switch is set to off. - REN number may exceed 4, for all telephones connected to the line. Disconnect a phone until the number is below 4. If there are still problems, and you have more than one telephone : Remove the "problem" phone. Insert another phone and check that it works. If "yes" then the "problem" phone is possibly faulty. If not, then you may have a faulty line. Try using the other socket and see which phones work. If you do have a faulty line then you sho
Resumo do conteúdo contido na página número 12
We look to you, our customer, to be reasonable and sensible over the warranty. We will endeavour to repair any telephone sent in to us within the warranty period but we reserve the right to charge for items that we consider replaceable under wear and tear. For example, if a handset cord splits within a few months, it will be replaced. If a phone is returned after, say, four years of heavy use with a similar problem, we might take a different view and wish to charge. If you have a genuine warrant
