Resumo do conteúdo contido na página número 1
Adam Equipment
WBW SERIES
WBW..M EC and WBW..aM NTEP
Type Approved
(P.N. 303669031, Revision E4, May 2013)
© Adam Equipment Company 2013
Resumo do conteúdo contido na página número 2
© Adam Equipment Company 2013
Resumo do conteúdo contido na página número 3
CONTENTS 1.0 INTRODUCTION ......................................................................................................3 2.0 SPECIFICATIONS ....................................................................................................4 3.0 INSTALLATION ........................................................................................................6 3.1 UNPACKING ..................................................................................................
Resumo do conteúdo contido na página número 4
© Adam Equipment Company 2013 2
Resumo do conteúdo contido na página número 5
1.0 INTRODUCTION • The WBW range provides accurate, fast and versatile general purpose weighing scales with check-weighing functions. • There are four series within the range- WBW..M, WBW.., WBW..a and WBW..aM • The WBW..M scales are configured at the factory for compliance with EN 45501, OIML R-76. Type Approval Number T7476/TC7477. • The WBW..aM are NTEP approved. NTEP certificate 10-082. Approved scales have different capacities and readabilities from the standard WB
Resumo do conteúdo contido na página número 6
2.0 SPECIFICATIONS EC Type Approved Models (Type Approval Number T7476/TC7477) WBW 3M WBW 6M WBW 15M Kilograms Max 3 kg 6 kg 15 kg e = 0.001 kg 0.002 kg 0.005 kg Grams Max 3000 g 6000 g 15000 g e = 1 g 2 g 5 g NTEP Type Approved Models (Type Approavl number 10-082) WBW 6aM WBW 15aM WBW 30aM Pounds Max 6 lb 15 lb 30 lb e = 0.002 lb 0.005 lb 0.01 lb Grams Max 3 kg 6 kg 15 kg e = 0.001 kg 0.002 kg 0.005 kg WBW 2 / 5a WBW 4 / 9a WBW 8 / 18a WBW 16 / 35a Kilogra
Resumo do conteúdo contido na página número 7
Pounds:Ounces Maximum Capacity 5 lb: 0.00 oz 9 lb:0.00 oz 18 lb:0.0 oz 35 lb: 0.0 oz Readability 0.01 oz 0.02 oz 0.1 oz 0.1 oz Repeatability (S.D.) 0.01 oz 0.02 oz 0.1 oz 0.1 oz Linearity (±) 0.02 oz 0.04 oz 0.2 oz 0.2 oz OTHER SPECIFICATIONS Units of measure WBW..M kg, g WBW..aM lb, kg, g, oz WBW/WBW..a kg, g, lb, oz, lb:oz Tare Full range Stabilisation Time 2 seconds typical Operating -10°C to 40°C Temperature Power supply 12 VDC, 800 mA Through
Resumo do conteúdo contido na página número 8
3.0 INSTALLATION 3.1 UNPACKING Remove the scale from the packing carefully. Inside the box you will find everything needed to start using the scale- Pre-assembled scale Stainless steel top pan Power Supply Module Operators Manual 3.2 LOCATING • The scales should not be placed in a location that will reduce the accuracy. • Avoid extremes of temperature. Do not place in direct sunlight or near air conditioning vents. • Avoid unsuitable tab
Resumo do conteúdo contido na página número 9
3.3 SETTING UP • The WBW Series comes with a stainless steel pan. Place it on the top if already not installed. • Do not press with excessive force as this could damage the load cell inside. • Level the scale by adjusting the four feet. The scale should be adjusted such that the bubble in the spirit level is in the centre of the level and the scale is supported by all four feet. • Attach the power supply module to the bottom of the scale and plug into the mains. Attach
Resumo do conteúdo contido na página número 10
4.0 KEYPAD KEYS PRIMARY FUNCTION SECONDARY FUNCTION Switches the scale on or off [O/I] [Zero] Sets the zero point for all Escapes from a parameter or an subsequent weighing. The option without changing the display shows zero. value. [Tare] Tares the scale and stores the Enters the selected parameter or current weight in memory as a value for setting. tare value, subtracts the tare value from the total weight and shows the results. This is the net weight. [
Resumo do conteúdo contido na página número 11
5.0 DISPLAY The LCD will display a decimal point in the WBW..a and WBW..aM models or a comma as shown in the WBW and WBW..M models. 6.0 SYMBOLS AND INDICATORS The LCD has unique symbols to indicate the following: The display is at Zero 0 The scale is Stable Net weight- The scale has been tared Net Symbols shown for the units kg / g / lb / oz / lb:oz Capacity Tracker- A bar graph indicating the proportion of the scale capacity being used by the weight
Resumo do conteúdo contido na página número 12
7.0 BATTERY OPERATION • The scales can be operated from the battery, if desired. The battery life is approximately 50 hours. • When the battery needs charging a symbol on the display will turn on. The battery should be charged when the symbol is on. The scale will still operate for about 20 minutes after which it will automatically switch off to protect the battery. • To charge the battery, simply attach the power supply module to the scale and plug in. The scale does not nee
Resumo do conteúdo contido na página número 13
10.0 OPERATIONS 10.1 ZEROING • You can press the [Zero] key at any time to set the zero point from which all other weighing and counting is measured. This will usually be necessary when the platform is empty. When the zero point is obtained the display will show the zero indicator. • The scale has an automatic re-zeroing function to account for minor drifting or accumulation of material on the platform. However you may need to press [Zero] to re-zero the scale if small amo
Resumo do conteúdo contido na página número 14
NOTE: When the container is removed a negative value will be shown. If the scale was tared just before removing the container, this value is the gross weight of the container plus all products which were removed. The zero indicator will also be on as the platform is back to the same condition it was when [Zero] was pressed last. Press [Tare] or [Zero] to remove the tare value and display zero. The Net indicator will disappear. 10.3 WEIGHING To determine the weight of a sample
Resumo do conteúdo contido na página número 15
2. The limits can be locked by the manager. A Limit Password must be used to change the limits or recall other limits from memory. 3. If Limit Password is enabled then enter the password which will allow you to change the limits or the operation of the beeper or bargraph. Setting up Check-weighing • Press the [Limit] key. It will show the last used high limit. • The user will be asked for the password if the current check- weighing password is anything other than “0000”. S
Resumo do conteúdo contido na página número 16
12.0 CALIBRATION 12.1 WBW..M and WBW..aM APPROVED SCALES, CALIBRATION The scales are sealed to prevent unauthorised access to the circuit boards and load cell. One method calibration of the WBW-M scale is accomplished by breaking the security seals to gain access to the circuit boards inside. See the figures on the security seal as given below. WARNING: BREAKING OF THE SEALS MAY MAKE IT ILLEGAL TO USE THE SCALES FOR SALES OF GOODS. CONTACT YOUR TRADING STANDARDS OFFICE FOR FURT
Resumo do conteúdo contido na página número 17
WBW..aM SECURITY SEALS: The device is equipped with a Category 1 Audit Trail. In addition a lead &wire and/or a paper security seal may be installed. To access the audit trail press the [Zero] button for 3 seconds. The display will flash the calibration counter and the configuration counter. 12.3 CALIBRATION COUNTER The scales are sealed to prevent unauthorised calibration. However it is possible to calibrate the scales as the software includes a counter to keep track of how many tim
Resumo do conteúdo contido na página número 18
• Press the [Tare] key when the stable indicator is on. • The scale will calibrate to the mass and then return to weighing. • Remove the calibration weight as soon as calibration is complete. NOTE: If an error message “FAIL H” or “FAIL L” is shown during calibration, re- check the calibration and repeat, if necessary. If the error cannot be corrected contact your dealer or Adam Equipment for advice. © Adam Equipment Company 2013 16
Resumo do conteúdo contido na página número 19
13.0 PARAMETER SETTING This section allows the user to access the parameters for customising the scale. The parameters are split into 2 groups- 1. Check weighing Parameters 2. Scale Parameters In the following sections use the [Limit] key to scroll through the options, the [Tare] key to accept the option and the [Zero] key to return to weighing. Wherever numeric values are required to be entered, use the [Limit] and [Unit] keys to increment the flashing digits as explained i
Resumo do conteúdo contido na página número 20
“donE”. If the old parameter is other than “0000”, enter the old one when “P _ _ _ _” is displayed and then enter the new password twice when asked. When complete, it will display “donE”. 13.2 SCALE PARAMETERS To enter this section press and hold the [Unit] key for 4 seconds. The display will go directly to “S1 Un”. These parameters are used to control the operation of the scale. Parameter Description Options Default setting Enable or disable weighing units, will S
