Краткое содержание страницы № 1
L-Series
Color Camera
PAL
NTSC
HCC334L HCC334LX
HCC484L HCC484LX
HCC335LX
HCC485LX
User Guide
Document G-113077-001 – 02/07 – Rev 3
Краткое содержание страницы № 2
Revisions Issue Date Revisions 1.00 06/06 New document 1.01 08/06 Added 230V (HCC335LX, HCC485LX). 3 02/07 Updated document part no.; added warning to p. iii. Rev 3 ii G-113077-001 02/07
Краткое содержание страницы № 3
Warnings Installation and servicing should be performed only by qualified and experienced personnel to conform to all local codes and to maintain your warranty. WARNING! 12 VDC/24 VAC models require the use of CSA Certified/UL Listed Class 2 power adapters to ensure compliance with electrical safety standards. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. WEEE (Waste Electrical and Electronic Equipment).
Краткое содержание страницы № 4
FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harm
Краткое содержание страницы № 5
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . 2 Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Camera Functions . . . . . . . . . . . . . . . . . . . . . . . . 3 Setting Up Your Camera . . . . . . . . . . . . . . . . .
Краткое содержание страницы № 6
Introduction The Honeywell L-Series Color cameras are ideally suited for use in day-to-day surveillance applications. The L- Series cameras are designed for exceptional value and performance for everyday use. Their off-the-shelf feature set is designed for high picture quality in standard applications and they require little to no adjustment after installation. Figure 1 Camera Overview C/CS mount adapter: C mount: turn Lens connector for counterclockwise Auto Iris lens plug CS mount: turn
Краткое содержание страницы № 7
Before You Begin Please read this guide carefully before you install the L-Series Color camera. Keep this guide for future reference. Unpack Everything Check that the items received match those listed on the order form and packing slip. The L-Series packing box should include, in addition to this User Guide: � One L-Series Color camera � One Auto Iris lens plug If any parts are missing or damaged, contact the dealer you purchased the camera from or call Honeywell Customer Service (see Cont
Краткое содержание страницы № 8
Camera Settings Camera Functions Figure 2 Camera Rear View Mains 230V —Line Voltage Low Voltage (HCC335LX, HCC485LX) (HCC334L/X, HCC484L/X) 4 9 7 8 10 10 7 8 9 4 VIDEO IR IS VID EO LEVEL V-P H PU SH IR IS LOC K LEVEL V-PH PU SH LOC K 1 EE ME PW R L/L L/L AES AI PW R 6 BLC EE ME 3 FL AES AI AG C ~207-253VAC 50H Z IN T BLC IN T OFF WB3 FL VSD WB2 VSD AGC OFF WB1 5 WB3 2 WB2 DC DC 12V GN D WB1 AC 24V DC 6 Legend #Description 1 DIP switches for mode settings (see Figure 3) 2 Auto Iris Lens select sw
Краткое содержание страницы № 9
Setting Up Your Camera Figure 3 shows the factory set DIP switch settings. Automatic Gain Control (AGC) and Auto White Balance Control (AWC) are set ON. Figure 3 Factory Set DIP Switch Settings IRIS LEVEL EE ME VIDEO PUSH IRIS LOCK LEVEL V-PH AES AI PWR L/L OFF BLC EE ME AES AI BLC INT OFF FL FL VSD AGC OFF WB3 VSD WB2 OFF DC 12V + - GND WB1 AGC AC 24V DC OFF WB3 OFF WB2 OFF WB1 DC = ON = OFF Selecting the Lens Manual Lens Set the EE/ME DIP switch on the rear of the camera (see Figure 3) to E
Краткое содержание страницы № 10
2. Slowly turn the LEVEL potentiometer until the picture on the monitor is as clear as possible and is not too bright. Video Drive (VSD) Lens Set the VSD/DC switch on the rear of the camera (see Figure 3) to VSD. Exposure Mode Automatic Exposure Mode The Electronic Exposure feature compensates for excessive light levels by automatically adjusting the shutter speed of the camera. Set the EE/ME switch to EE (recommended setting). Manual Exposure Mode Set the EE/ME switch to ME. This setting
Краткое содержание страницы № 11
Backlight Compensation (BLC) If there is excessive light (for example, a window exists in a scene), the camera tries to compensate by reducing the overall exposure, resulting in the areas surrounding the window becoming too dark. Turn the BLC switch ON to eliminate the silhouette effect. Flickerless Mode (FL) Set the FL switch to ON to remove the flicker in a picture. For PAL models, the shutter speed is 1/100 second; for NTSC models, the shutter speed is 1/120 second. Automatic Gain Contr
Краткое содержание страницы № 12
Auto White Balance Control (AWC) This mode covers a wider range of 2000°K to 10000°K and performs at a faster operating speed than ATW mode. This mode is typically used for outdoor applications or where variable lighting conditions exist. One Push Lock Press PUSH LOCK on the rear of the camera to calibrate the white balance for the current scene. This mode is typically used for scenes with constant lighting conditions. Synchronization Selection (LL/INT) This switch selects the synchronizati
Краткое содержание страницы № 13
Line Lock Phase Adjustment Potentiometer When the camera is in Line lock mode, it is possible to adjust the point on the AC cycle at which the camera triggers. This feature allows for synchronization of cameras that are connected to different phases. The V-PHASE adjustment potentiometer allows the line lock phase trigger point to be adjusted by 270°. Rotating the potentiometer clockwise advances the trigger point and turning it counterclockwise retards the trigger point. The factory defa
Краткое содержание страницы № 14
Lens Installation Adjusting the Back Focus The back focus adjustment is accessible at the front end of the camera housing to adjust the back focal length or picture focus. The range of adjustment allows both C- and CS-mount lenses to be used without the need for a spacer ring. Figure 4 C/CS Mount CC S Setscrew 1. Loosen the setscrew with a Phillips screwdriver. 2. Adjust the focus ring to focus the picture. 3. Retighten the setscrew. Rev 3 9 G-113077-001 02/07
Краткое содержание страницы № 15
Figure 5 DC and VSD Lens Pin Definition Auto Iris lens connector 21 43 1 3 2 4 Pin DC (Direct Drive) lens Video (VSD) lens 1 CTRL - Power (+12V) 2CTRL + NC 3 DRV + Video Signal 4DRV - GND Set the select switch to DC Set the select switch to VSD Rev 3 10 G-113077-001 02/07
Краткое содержание страницы № 16
Completing the Installation Mounting the Camera Mounting points are provided on the top of the camera for mounting the camera on a bracket or tripod. They are designed to accept standard sized 1/4 x 20 mounting screws. This bracket can be unscrewed and mounted onto the opposite side of the camera, depending on your application. The mounting bracket must be capable of supporting the weight of the camera and its lens. Note Some installation codes dictate that the mounting bracket must be c
Краткое содержание страницы № 17
Connecting the Camera 1. Connect the VIDEO connector on the rear of the camera to the video-in connector on your monitor. 2. Connect the camera to a power supply appropriate for your installation. HCC334L/X, HCC484L/LX: 12 VDC or 24 VAC power supply HCC335LX, HCC485LX: 230V power supply 3. Plug in the power supply. The power (PWR) LED illuminates to show that the camera is receiving power. If it does not illuminate, check the connections and the power source. Figure 7 Camera Connections Lo
Краткое содержание страницы № 18
Warranty and Service Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective product returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service at 1.800.796.CCTV (North America only) for assistance or to request a Return Merchandise Authorization (RMA) number. For Europe and the United Kingdom, please contact your Honeywe
Краткое содержание страницы № 19
HCC334L HCC334LX HCC484L HCC484LX HCC335LX HCC485LX Video Output: 1 Vp-p @ 75 Ohms Sync System: Internal/Line lock S/N Ratio: > 50 dB Auto Gain On (30 dB)/Off (11 dB) Control (AGC): ALC: EE/VSD/DC Automatic 1/60 - 1/50 - 1/60 - 1/50 - Electronic 1/100,000 1/100,000 1/100,000 1/100,000 Shutter (AES): sec sec sec sec Lens Mount: C/CS mount (adjustable) White Balance ATW/AWC/One Push Lock/Indoor/Outdoor/ (AWB): Fluorescent/User BLC: On/Off Gamma: 0.45 Electrical Input Voltage: HCC334L/LX, HCC484L
Краткое содержание страницы № 20
Honeywell Video Systems (Head office) Honeywell Video Systems 2700 Blankenbaker Pkwy, Suite 150 Northern Europe Louisville, KY 40299, USA Netwerk 121 www.honeywellvideo.com 1446 WV Purmerend, The Netherlands ℡ +1.800.796.2288 www.SecurityHouse.nl ℡ +31.299.410.200 Honeywell Security Australia Pty Ltd. Unit 5, Riverside Centre Honeywell Video Systems UK Ltd. 24-28 River Road West Aston Fields Road, Whitehouse Ind Est Parramatta, NSW 2150, Australia Runcorn, Cheshire, WA7 3DL, UK www.ademco.com.a
