Краткое содержание страницы № 1
Accessory Application Publications No.
AII 25886
INSTALLATION
XM RADIO SYSTEM
2003-2004 PILOT
Issue Date
INSTRUCTIONS
AUG 2003
The XM Radio system will not fit in a vehicle
equipped with a navigation system or a rear
15 Wire ties
entertainment system.
PARTS LIST
XM Radio Attachment Kit (sold separately):
5 Wire ties with clips
P/N 08B15-S9V-100
DIN cable
2 Cushion tapes
XM radio harness
7 EPT sealers
Fuse label
Unit bracket
2 Subantenna cables
Double-sided adhesive tape,
53 x 28 mm
Harness hook
Краткое содержание страницы № 2
XM Antenna Kit (sold separately): TOOL AND SUPPLIES REQUIRED P/N 08A15-1E1-100 #2 Phillips screwdriver Flat-tip screwdriver Utility knife Antenna Diagonal cutters Push pin Tape measure Shop towel Scissors Base Kit (sold separately): Ratchet P/N 08A15-1E1-000 8 mm, 10 mm, and 14 mm Sockets 8 mm, 10 mm, and 14 mm Combination wrenches Felt-tip pen Display module Isopropyl alcohol Drill 3 mm and 10 mm drill bits Eye protection (face shield, safety goggles, etc.) FM modulator unit Receiver unit Owner
Краткое содержание страницы № 3
Illustration of an Installed XM Radio System INSTALLATION Customer Information: The information in this installation instruction is intended for use only by ANTENNA skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. FM MODULATOR 2. Disconnect the
Краткое содержание страницы № 4
4. Remove the four screws that fasten the audio 6. Remove the center panel (four self-tapping screws bracket. Pull the audio unit out toward you, and and two clips, and unplug the vehicle accessory unplug the vehicle connector and antenna cable power outlet). from the rear of the audio unit. If equipped with a cassette/in-dash CD changer, unplug the CLIPS (2) additional connectors. VEHICLE CONNECTOR CENTER (If equipped, unplug the PANEL ANTENNA additional connectors.) CABLE AUDIO UNIT AUDIO BRAC
Краткое содержание страницы № 5
8. Remove the four screws that fasten the left and 10. Slide the clip nut onto the display module pocket right vehicle bracket. Pull the heater control unit flange. and pocket toward you, and unplug the vehicle connectors. DISPLAY MODULE VEHICLE POCKET FLANGE CONNECTOR HEATER CONTROL UNIT CLIP NUT LEFT VEHICLE BRACKET Clean with isopropyl alcohol. DISPLAY MODULE POCKET SCREW RIGHT VEHICLE DISPLAY BRACKET MODULE 3131010M 9. Remove the left and right vehicle brackets (six self-tapping screws), and
Краткое содержание страницы № 6
16. Remove the driver's seat rear cover (four clips). 14. Fit the DIN bezel around the display module Take care not to damage the clips. pocket. Set the heater control unit on the display module pocket, and reinstall the left and right vehicle brackets using the two self-tapping screws removed in step 9. Attach the display module to DRIVER’S SEAT brackets with three self-tapping screws supplied with the XM radio attachment kit. SELF- LEFT TAPPING VEHICLE SCREW HEATER BRACKET (Reuse.) CONTROL UNI
Краткое содержание страницы № 7
18. On the driver’s side of the vehicle, remove the 20. Route the XM radio harness and two subantenna center console lower cover (gently pull the cover cables from the dashboard opening to driver’s out toward you to release the seven clips). Take floor. Using one cushion tape, attach it to the care not to damage the clips. vehicle frame. DRIVER’S DASHBOARD SEAT OPENING Align. CUSHION TAPE 50 mm DRIVER’S CENTER CONSOLE LOWER CLIPS (7) COVER 19. Get the XM radio harness, the subantenna cables, Cle
Краткое содержание страницы № 8
22. Plug the audio unit vehicle 20-pin connector into 25. Place the display module/heater control unit the XM radio 20-pin connector that is blue-taped to assembly near the dashboard opening, and route the XM radio harness. Wrap one EPT sealer the display module cable along the XM radio around the subantenna cable in the area shown. harness and the subantenna cables. SUBANTENNA VEHICLE FRAME CABLE EPT (Clean with EPT SEALER SEALER isopropy alcohol.) SUBANTENNA CABLE DISPLAY MODULE CABLE VEHICLE
Краткое содержание страницы № 9
28. Plug the XM radio harness 20-pin connector and 30. Continue routing cables through the center sub antenna cable into the audio unit, and console and toward the rear of the vehicle. Using carefully slide the audio unit into the dashboard. scissors, cut one cushion tape in half. Clean the Reinstall the four audio unit screws. vehicle frame with isopropyl alcohol, and attach half of the cushion tape to the vehicle frame in the area shown. XM RADIO HARNESS 20-PIN CONNECTOR VEHICLE FRAME (Clean w
Краткое содержание страницы № 10
33. Measure and slit the driver’s floor carpet in the Installing the Antenna area shown. Be careful not to damage the 35. On the driver's side of the vehicle, remove the subantenna cables and XM radio harness when weatherstrip from the left front door opening in the cutting the floor carpet. area shown, then remove the left front "A" pillar trim (two clips). FLOOR CLIPS (2) CARPET slit 50 mm WEATHERSTRIP WIRE TIE LEFT FRONT "A" PILLAR TRIM DISPLAY MODULE CABLE 36. Remove the dashboard side cover
Краткое содержание страницы № 11
37. Remove the fuel lid door opener lever, then 39. Get two EPT sealers. Using scissors, cut two remove the left front door sill trim (three clips and EPT sealers into six pieces. Wrap the them two retaining tabs). around the antenna unit cable at the measurements shown. ANTENNA RETAINING UNIT TAB 60 mm 200 mm 60 mm FUEL LID DOOR 60 mm OPENER LEVER 60 mm 60 mm LEFT FRONT DOOR SILL TRIM ADHESIVE BACKING (Remove.) 60 x 60 mm DOUBLE-SIDED ADHESIVE TAPE Cut. EPT SEALER 40. Using isopropyl alcohol o
Краткое содержание страницы № 12
43. Route the antenna unit cable along the front 45. Secure the antenna unit cable to the vehicle windshield and the top of the dashboard. Insert the harness with two wire ties. antenna unit cable with the EPT seals between the windshield and the dashboard. ANTENNA UNIT CABLE VIN IDENTIFICATION ANTENNA PLATE UNIT CABLE (Don’t hide the VIN number with the Insert. antenna unit cable.) VEHICLE HARNESS FRONT WINDOW GLASS ANTENNA UNIT CABLE Insert. WIRE TIES Route under the DASHBOARD dashboard. 2N270
Краткое содержание страницы № 13
47. Continue routing the antenna unit cable alongside 50. Get the DIN cable. Plug the DIN cable into the FM the vehicle harness, and out through the hole in modulator unit and the receiver unit. the floor carpet under the driver's seat. Secure the antenna unit cable to the vehicle harness with four FM RECEIVER UNIT wire ties in the area shown. MODULATOR UNIT ANTENNA FLOOR UNIT CABLE CARPET HOLE UNIT BRACKET DIN CABLE 51. Position the unit assembly under the driver’s seat. WIRE TIES Plug the XM r
Краткое содержание страницы № 14
53. Get the five wire ties with clips and two wire ties. 55. Slide the driver's seat forward, and install the unit Secure all of the cablse to the unit bracket in the bracket to the driver’s seat rails using four order shown: 6 x 12 mm washer-bolts. Tighten the bolts securely. XM radio harness, subantenna cables, and the DRIVER’S SEAT display module cable. UNIT BRACKET XM radio harness, subantenna cables, and the display module cable. 6 x 12 mm WASHER- Antenna unit cable, XM radio harness, BOLTS
