Краткое содержание страницы № 1
SNOW CONE CART™
Model # SCC-200
For Household Use Only!
Read These Instructions Before Using
This Unit!
SAVE THESE INSTRUCTIONS!
Краткое содержание страницы № 2
ENGLISH 1 IMPORTANT PRECAUTIONS Appliance Specifications: 120 Volts 60 HZ 100 Watts ETL Approved Important Precautions to Remember: A. NEVER immerse in water. B. NEVER use near water. C. NEVER use an abrasive sponge or cloth. D. NEVER use a scouring pad on the unit. E. NEVER leave unit unattended while in use. F. NEVER try to force the cover in the locking mechanism. G. Unplug unit from outlet when not in use and when cleaning. H. DO NOT operate thi
Краткое содержание страницы № 3
ENGLISH 2 IMPORTANT SAFEGUARDS (Continued) 8. DO NOT use outdoors. 9. DO NOT let the cord hang over the edge of table or counter tops, or touch hot surfaces. 10. DO NOT place on or near a hot gas or electric burner, or in a heated oven. 11. Extreme caution must be used when moving this appliance. 12. DO NOT use the appliance for other than its intended use. 13. A unit that is plugged into an outlet should not be left unattended. 14. Check ice hopper for presence of f
Краткое содержание страницы № 4
ENGLISH 3 ASSEMBLY After Taking the Unit Out of the Box: Your SNOW CONE CART™ requires some assembly before first use. The Main Unit, which includes the ice grinder, is already assembled. You will need to put together the cart itself using the instructions that follow. Before first use, make sure to wipe clean the inside of the Main Unit with a non-abrasive moist sponge, a non-abrasive towel, or a damp cloth followed by a non-abrasive dry towel. BREAKDOWN Parts
Краткое содержание страницы № 5
ENGLISH 4 ASSEMBLY (Continued) Screws, Studs, and Nuts 1 2 3 4 5 6 7 8 ASSEMBLY Main Unit Storage Compartment Base Support 1. Open the box and remove all parts including the Main Unit, Storage Compartment, Wheels, Legs, and all other contents (including the Push Handle and accessories). 2. Attach the Push Handle to the Storage Compartment using four of the #1 screws (as shown below):
Краткое содержание страницы № 6
ENGLISH 5 ASSEMBLY (Continued) 3. Connect the Base Supports by screwing two of the #1 screws into the Cross Bar (as shown below): 4. Connect the Leg Assembly by screwing four of the #3 studs from the Base Support into the Leg Assembly (as shown below). Make sure to screw from the Base Support into the Leg Assembly and not vice versa. Once the studs are firmly screwed through, place the four #8 Nut Caps over the studs for cosmetic purposes: 5. Now that the Leg Ass
Краткое содержание страницы № 7
ENGLISH 6 ASSEMBLY (Continued) 6. Attach the Wheels to the Base Support by using two of the #4 Wheel Rods. Slide a #5 Lock Washer onto a Wheel Rod, and then push the Wheel Rod through the holes in the Base Support. Make sure to place the two #6 Flat Washers between the Base Support and the Wheels. Repeat on the other wheel. Finally, place the two #7 Wheel Rod Caps on the outside of the screws for cosmetic purposes (as shown below): 7. Place the Main Unit onto the S
Краткое содержание страницы № 8
ENGLISH 7 USING YOUR SNOW CONE CART™ USING YOUR SNOW CONE CART™ First, find a stable surface near an electrical outlet before starting. (Make sure your cord is away from any water source. If needed, it is acceptable to use an extension cord.) 1. Before plugging in your unit, add ice cubes by removing the clear lid from the Main Unit of your SNOW CONE CART™. In order to do so, simply push the release button on the lid, lift and remove. Once you have done this, plug in the
Краткое содержание страницы № 9
ENGLISH 8 REPLACING THE BLADE (Continued) When following the next three steps, use EXTREME CAUTION as the blade is very sharp! Once the Ice Tray is removed, you are fully exposed to the blade inside! 2. Once the Disassembly Tool is properly inserted, twist counter-clockwise (as the arrow shows) and lift the Ice Hopper out. BLADE IS NOW COMPLETELY EXPOSED – USE CAUTION 3. Locate the two plastic clips on the Blade Assembly and use a spoon and your thumb
Краткое содержание страницы № 10
ENGLISH 9 CLEANING 1. Make sure the unit is unplugged before cleaning. 2. Open the housing door to clean and dry inside of unit using a slightly damp, non- abrasive sponger or non-abrasive towel. 3. Also use a slightly damp, non-abrasive sponge or non-abrasive towel to wipe clean outside of unit, then wipe with a non-abrasive dry towel to dry. 4. The shaving unit and clear lid are dishwasher safe. To take out the shaving unit, simply turn the white top in a counter-clockwis
Краткое содержание страницы № 11
ENGLISH 10 RETURNS & WARRANTY SHOULD YOUR UNIT NOT WORK OR IS DAMAGED WHEN YOU FIRST TAKE IT OUT OF THE BOX, PLEASE RETURN IT TO THE PLACE OF PURCHASE IMMEDIATELY. Should you have any questions, please contact us via email or at the customer service number listed below between the hours of 8:00 AM and 5:00 PM, Monday through Friday, Central Standard Time. Distributed by: Nostalgia Products Group LLC 1471 Partnership Dr. Green Bay, WI 54304-5685 Customer Service Phone: (
Краткое содержание страницы № 12
Nostalgia Products Group LLC 1471 Partnership Dr. Green Bay, WI 54304-5685 Visit Us Online at www.nostalgiaelectrics.com ©2009 Nostalgia Products Group LLC Rev. 4/28/09
