Краткое содержание страницы № 1
Owner's Manual
®
Liquid Propane Gas Grill
Model 141.16223
WARNING: Note to Installer: Leave this Owner's Manual
with the consumer after delivery and/or installation.
Read this Owner's Manual carefully and be sure
your gas grill is properly assembled, installed and
Note to Consumer: Leave this Owner's Manual
maintained. Failure to follow these instructions
in a convenient place for future reference.
could result in serious bodily injury and/or property
damage. This gas grill is intended for outdo
Краткое содержание страницы № 2
Z_WARNING Warranty ..................................................... 2 Combustion byproducts produced when using Safety Instructions ..................................... 2 this product contain chemicals known to the State of California to cause cancer, birth Hardware .................................................... 5 defects, or other reproductive harm. Parts Diagram and Lists ........................ 7 AkWARNING Assembly Instructions .............................. 10 Failure to comply
Краткое содержание страницы № 3
Correct LP Gas Tank Use • LP gas tanks must be stored outdoors in a LP gas grill models are designed for use with a well-ventilated area and out of the reach of standard 20 lb. Liquid Propane Gas (LP gas) tank, children. Disconnected LP gas tanks must not not included in grill box. Never connect your gas be stored in a building, garage or any other grill to an LP gas tank that exceeds this capacity. enclosed area. A tank of approximately 12 inches in diameter by 18-1/2 inches high is the maximum
Краткое содержание страницы № 4
CAUTION: Spiders and small insects occa- To reduce the chance of "FLASHBACK" (see sionally spin webs or make nests in the grill CAUTION at left) clean the Burner Tubes and Burner Tubes during transit and warehousing. Burners before fully assembling your grill. These webs can lead to a gas flow obstruc- Remove the Cotter Pin from the rear underside tion which could result in a fire in and around of each Burner using a pair of long nose pliers. the Burner Tubes. This type of fire is known Carefull
Краткое содержание страницы № 5
The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly. Ref. Component Qty. Purpose of Components $211G06352 Wheel Bolt 3/8"x3-3/8" 2 Install Wheels To Cart Legs $431M08152 Spring Washer 2 $313G06082 Nut 3/8" 2 $132G04082 Pattern Head Screw 1/4"xl/2" 6 Attaches Foldable Cart Legs $135G04332 Pattern Head Screw 1/4"x2-3/4" 8 Attaches Cart Legs To Cart Bottom Shelf $132G04122 Pattern Head Screw 1/4"x3/4" 4 Attaches
Краткое содержание страницы № 6
Size and Quantity of each Hardware Piece: Nut 3/8" Wheel Bolt 3/8"x3-3/8" Spring Washer Qty, 2 Qty. 2 Qty. 2 Ref, # $431M08152 Ref. # S211G06352 Ref, # $313G06082 Pattern Head Screw 1/4"x2-3/4" Pattern Head Screw 1/4"x3/4" Pattern Head Screw 1/4"xl/2" Qty, 8 Qty. 8 Qty, 6 Ref, # $135G04332 Ref, # $132G04122 Ref, # $132G04082 Wing Bolt 1/4"x4-3/8" Battery/AA Wrench/No.17 Customized Qty, 1 Qty. 1 Qty. 1 Ref, # $233G04382 Ref, # P05301001A Ref, # P05515101L Scale 1:2 Scale 1:2 Scale 1:2 Lighting St
Краткое содержание страницы № 7
1 4 6 5 3,(L) 11 lO 7
Краткое содержание страницы № 8
PART# REF# DESCRIPTION QTY 1, Lid P00138014D 2, Lid Hinge Support, Right P03320001H 3, Lid Hinge Support, Left P03320002H 4, PO0601174A Temperature Gauge 5, Lid Handle P00205006B 6, Name Plate P00410037C 7, Cooking Rack/Secondary P01504001E 8, 3 Cooking Grid P01602001E 3 9, Flame Tamer/Steel P01705002E 10, 3 P02001008C Burner/Main with Heat-insulating Ring 1 11, Burner Bracket P02203021B 2 12, Gas Collector Box with Electrode PO2608001A 1 13, Electric Wire Set P02615003A 14, P02502024C Electric
Краткое содержание страницы № 9
REF#DESCRIPTION PART# QTY 36, Tightening Tool P05515102K 1 37. Lighting Stick P05313023B 1 38, TowelRack PO5209001A 1 39, ToolHolder PO5514003F 1 40, ToolHook PO5514053A 5 41. SideBurner Lid PO0115031P 42, SideBurnerPotSupport PO0805013B 43. SideBurnerElectrode P02607042J 44. SideBurner P02002041C 45. SideBurner GasValveAssembly PO3218003G 46. SideBurner Connection Tube PO3705002A 47. Regulator withHose/LPG PO3601002A 48. Control Knobfor SideBurner P03426061C 49, BowlWindShield POO73701]B 50. Si
Краткое содержание страницы № 10
CAUTION: While it is possible for one person to assemble this grill, obtain assistance from another person when handling some of the larger, heavier pieces, especially the grill head. 1. During unpacking and assembly always wear work gloves and eye protection. 2. Open Lid of shipping carton and remove top sheet of cardboard. Lay cardboard sheet on floor and use as a work surface to protect floor and grill parts from scratches. 3. Remove packing materials and cart parts from shipping carton. 4. Y
Краткое содержание страницы № 11
H NOTE: Before attaching the Cart Bottom Shelf to Cart be sure tank hole on the Bottom is located on the right side. Install the Cart Bottom Shelf between the Cart Legs. Align the holes on Cart Legs with the threaded holes at the corners of Cart Bottom Shelf. Attach loosely the 8 screws then tighten screws. D Pattern Head Screw 1/4"x2-3/4" Qty. 8 Ref. # S135G04332 1. Screw the 2 Casters into the Caster Seats. Turn the threaded Caster Stem by hand, clockwise until it stops. Tighten securely using
Краткое содержание страницы № 12
H Be surebothCastersare locked,thenwiththe assistanceof anotherperson,turn the assembled grillupright. H Installing Grease Draining Tray Kit 1. Position Grease Draining Tray Heat Shield into slots in Grease Draining Tray. See W 2. From the back side of Grill Head install the Grease Draining Tray and Grease Draining Tray Heat Shield. The Grease Draininq Tray Heat Shield is required to be present and centered for your safety. 3. Insert two M4x8mm Pattern Head Screws into the threaded holes on the
Краткое содержание страницы № 13
_ Installing Towel Rack Remove theWashers andPatternHeadScrews fromtheTowelRackandusethemto securethe TowelRackto FrontSideof LeftSideShelf. Pattern Head Screw M5x8mm Qty, 2 Ref. # $132M05082 Plain Washer M5 Qty. 2 Ref. # $411M05136 H Installing Tool Holder Kit Remove the Washers and Pattern Head Screws from the Tool Holder. Slide the 5 Tool Hooks onto the Tool Holder with the hooks facing the Side Burner Frame. Use the 2 screws and washers removed in the first step to secure the Tool Holder to
Краткое содержание страницы № 14
_r_ Installing Side Burner Kit 1. Attach the Side Burner Gas Valve Assembly to the Side Burner Gas Valve Hole on the Side Burner Frame. See _ Align the 2 holes on the Side Burner Frame with the threaded holes on the Side Burner Gas Valve Bracket. Tighten securely using 2 screws and washers provided. 2. Cut Fastening Band from Pot Support and set Pot support aside. Install the Side Burner through the top hole in Side Burner Frame and onto the Side Burner Gas Valve. Make sure that opening at end o
Краткое содержание страницы № 15
_! Ignitor Battery Installation _'_ Electrode Check - Requires an Assistant 1. Remove the Ignitor Cap located on the grill Before placing the cooking components into your Control Panel. grill, ensure that the Spark Electrode Tip is propedy positioned within each Gas Collector Box (a 2. Place the manufacturer supplied AA battery 3-1/4" wide stainless mechanism found at the front into the Ignitor Slot. Be sure to place the between each set of Burners.) The easiest way to positive pole facing towar
Краткое содержание страницы № 16
SECONDARY _'_ Installing Cooking Components Important: Before cooking on your grill the first COOKING time, wash the Cooking Grids with warm, soapy water. Rinse and dry thoroughly. Season with cooking oil regularly. After cooking is completed, TAMER turn grill to HIGH setting for about five minutes to SLOT_ bum off excess grease or food residue. RACK 1. Place the 3 Steel Flame Tamers on the lower ledge above Burners. 2. Evenly space the Cooking Grids on the ledge above the Flame Tamers. 3. Place
Краткое содержание страницы № 17
Z WARNING If you smell gas: Basic Lighting Procedures • Shut off gas supply to the gas grill. • Turn the Control Knobs to OFF position. 1. Famitiadzeyourselfwiththesafetyguidetinesat the front of this manual. Do not smoke while • Extinguish any open flame such as candle, cigarette, lighter, etc., that could cause gas lighting grill or checking gas supply connections. to ignite. 2. Be sure the LP gas tank is filled. • Open the Grill Lid. • Get away from the LP gas tank. 3. Check that the end of e
Краткое содержание страницы № 18
• Misalignment of Ignitor on Burner _ Manually Lighting Your Grill by Match Correction: Check for proper position of the Electrode Tip as shown in step 7,12. The gap To light your gas grill by match, insert a match into the between the Spark Electrode Tip and Spark Lighting Stick and follow steps 1 through 6 of the Receiver should be approximately 3/16". Adjust Basic Lighting Procedures. Then, light the match and if necessary. With the gas supply closed and ait place Lighting Stick through the L
Краткое содержание страницы № 19
Cleaning the Grill Interior Burning-off the grill after every cookout will keep it ready for instant use. However, once a year you should Aswithallappliances, proper careandmaintenance give the entire grill a thorough cleaning to keep it in top willkeepyourgrillintopoperating condition and operating condition. Follow these steps: prolong itslife.Byfollowing thesecleaning procedures onatimelybasis, yourgrillwillstaycleanandwork 1. Turn all Burner Valves to the full OFF position. properiywith mini
Краткое содержание страницы № 20
Regardless of which Burner cleaning procedure you use, we recommend you also complete the following steps to help prolong Burner life. 1. Use a fiber pad or nylon brush to clean the entire To reduce the chance of FLASHBACK the procedure outer surface of each Burner until free of food below should be fallowed at least once a month in late residue and dirt. summer or early fall when spiders are most active or 2. when your grill has not been used for a period of time. Clean any clogged ports with a
