Краткое содержание страницы № 1
6<67(0
$50(’ 5($’< =21( =21( =21( =21(
9
Using Your
XP-400
Security System
NAPCO
Oi220a Tuesday, September 16, 1997 08:30
page 1
Краткое содержание страницы № 2
2 Oi220a Tuesday, September 16, 1997 08:30 page 2
Краткое содержание страницы № 3
Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-400 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those operating it with very easy, intuitive use. Please carefully review the information contained in this
Краткое содержание страницы № 4
Introduction Table of Contents System Information Keypad Controls and Indicators ................................ 5 Arming your System (When Leaving) ....................... 6 Central Station Phone Number: ____________________ Bypassing Zones ..................................................... 6 Protecting Yourself While Home ............................... 7 Central Station Account Number: ____________________ Emergency Keys ....................................................... 8 Disarm
Краткое содержание страницы № 5
9 9 6<67(0 $50(’ 5($’< =21( =21( =21( =21( 9 9 9 9 9 Keypad Controls and Indicators Numerical Keys 1-9, 0. Used to enter Armed Light will light when system is Armed,
Key Used to enable User Codes, Zone numbers, etc. and will flash when system is in Alarm special functions and op- tions. Press
and then the corresponding Spe- cial Function number Op- Ready Light will light when all zones are secure tion (See Special Func- and system is ready to be Armed. tions, Page 10) System Light
Краткое содержание страницы № 6
Arming Your System Arming Your System When Leaving 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your prot- ective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure these zones before proceeding. If any zones cannot be secured, see Bypassing zones below. 2 Enter your user code. The Green Ready light will go out, the Red Armed light will light. ARMED • If you make a mistake entering your code, pres
Краткое содержание страницы № 7
9 9 # ! Arming Your System Protecting Yourself While at Home 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure those zones before proceeding. 2 Enter your user code. The Green Ready light will go out, and the red Armed light will light. 3 Before your exit delay expires, press to bypass any interior zones, deactivating devices such
Краткое содержание страницы № 8
& & & Emergency Conditions Emergency Buttons Auxiliary The two sets of emergency buttons, if programmed, are always active whether the system is armed or Emergency disarmed. Discuss these buttons with your installer. The emergency signal will only be activated when Enabled? the two respective buttons are pressed at the same time. Yes No Auxiliary Alarm: Simultaneously press + to alert the central station of an auxiliary emergency, if so programmed. Police (The nature of
Краткое содержание страницы № 9
Disarming Your System / Silencing an Alarm Disarming Your System when Returning 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. ARMED 2 Enter your user code. The Red Armed light will go out, indicating that the system has been disarmed. READY Note: If you make a mistake entering your code, press the key and re-enter the code. SYSTEM Alarm Indication If the Red Armed lig
Краткое содержание страницы № 10
! ! Special Functions By pressing followed by the appropriate key, (do not press simultaneously) these special functions and features can be enabled: Instant Mode Easy Arm (when system is disarmed) Pressing followed by will cancel the Entry delay The Easy Arm feature allows the system to be armed by and put the system into the “Instant” mode. This is typic- pressing followed by . This will allow the easy ally done in the evenin
Краткое содержание страницы № 11
Programming User Codes Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program and/or reprogram up to 4 User Codes. The following explains how you will use this code to program or erase additional user codes. Entering the User Program Mode Press followed by and then enter the User 1 code. The Armed, Status and 9System Lights ARMED will flash, and the keypad will beep 4 times.
Краткое содержание страницы № 12
9 9 9 9 9 9 9System Troubles The XP400 is constantly monitoring its own components, as well as all critical services, such as AC Power and the Telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the Yellow SYSTEM light and beeping the keypad buzzer. If you cannot immediately clear the system trouble, the system can still be used. Simply press to view the trouble as de
Краткое содержание страницы № 13
9 9 9System Troubles Keypad Beeps or Zone light System Trouble Action ON Condition SYSTEM Flashes 2 Beeps 1 Bell / Siren Trouble There is a problem with the Bell or Siren. Call installing com- ARMED pany for service. READY 2 Beeps 3 Wireless Receiver A problem has been detected with the wireless receiver. SYSTEM Trouble Call installing company for service. 2 Beeps 4 Wireless Receiver A problem has been detected with a wireless receiver. Jam Call installing company for service. 3 Beeps 1-
Краткое содержание страницы № 14
9 9 Glossary Ambush Code - In the event that and then the zone number to bypass a premises.(Press while armed) zone. you are forced by an intruder to dis- arm your system, this special code Keypad Sounder - A local warning can be used to disarm the system, Central Station - Monitors alarm, device at the keypad to alert that Entry and simultaneously send a silent emergency and trouble reports from the delay has started, alarm to Central Station. If your sys- alarm system and notifies p
Краткое содержание страницы № 15
Notes 15 Oi220a Tuesday, September 16, 1997 08:30 page 15
Краткое содержание страницы № 16
NAPCO LIMITED WARRANTY NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects nor authorizes any other person purporting to act on its behalf to modify, to change, or to assume for it, any in materials and workmanship for thirty-six months following the date of manufacture. NAPCO will, within other warranty or liability concerning its products. said period, at its option, repair or replace any product failing to operate correctly without charge to the or
