Руководство по эксплуатации Pelco C1992M-A

Краткое содержание страницы № 1

®
Installation/Operation
PMC10A
High-Resolution Color Monitor
C1992M-A (12/03)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120

Краткое содержание страницы № 2

IMPORTANT SAFEGUARDS AND WARNINGS 1. Operate this unit only from the type of power source indicated on the label. 2. Do not block or cover ventilation openings on the back or bottom of the monitor cabinet. 3. Do not place this monitor near a radiator or heating vent. 4. Do not push objects of any kind through cabinet openings. This may result in fire or electrical shock. 5. Before adding attachments always ask a service technician to perform routine safety tests to deter- mine that equipment is

Краткое содержание страницы № 3

DESCRIPTION The PMC10A is high-resolution, 10-inch (25.4 cm) color monitor. The unit has a resolution of 350 TV lines producing an excellent-quality picture. The monitor's power input of 100-240 VAC, 50/60 Hz, is automati- cally detected upon power up. All image adjustment controls are conveniently located on the front panel of the monitor. [ ] Pelco Manual C1992M-A (12/03) 3

Краткое содержание страницы № 4

INSTALLATION The monitor may be placed on any flat surface (desk or table) or rack-mounted. To rack-mount the moni- tor follow the instructions supplied with the rack-mount kit. 1. Video Cable Connection (Refer to Table A for video coaxial cable requirements.) a. Connect the video cable to the BNC video input labeled V1 IN on the back panel of the monitor. b. Looping Operation Only - Connect a video cable to the BNC connector labeled V1 OUT. 2. Impedance Switch Setting a. Terminating Operation O

Краткое содержание страницы № 5

OPERATION 1. Set the video format switch located on the front panel to one of the following settings: VIDEO - Composite Video (NTSC) mode S-VIDEO - Use if the S-VIDEO input jack on the rear of the monitor is used 2. Turn the monitor ON. Wait 30 seconds for the picture tube to warm up and the power LED indicator to light. 3. If required adjust the picture using the control knobs on the front panel. Front Panel Adjustments TINT Color phase adjustment. Turn clockwise to increase the greenish tones

Краткое содержание страницы № 6

MAINTENANCE If the quality of the picture is poor and cannot be improved by making adjustments on the front control panel, inspect all system connections and cable runs. To reduce the risk of electrical shock, do not remove the cover or the back. No user-serviceable parts are inside. Refer servicing to qualified personnel, or contact the Pelco Customer Service Department for as- sistance. Refer to the Warranty and Return Information section. SPECIFICATIONS ELECTRICAL Input Voltage 100-240 VAC,

Краткое содержание страницы № 7

REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee th

Краткое содержание страницы № 8

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. ® • Three years on Genex Series products (multiplexers, server, and keyboard). ® • Three years on Camclosure and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X,