Руководство по эксплуатации Extron electronic MEDIALINK MLC 206

Краткое содержание страницы № 1

Setup Guide — MLC 206
™
The Extron MediaLink Controller (MLC 206) provides infrared (IR) and RS‑232
remote control of a display device, contact closure control of items in a room, tally
outputs, and MediaLink Switcher control.
This guide provides instructions for an experienced installer to set up and operate
the MLC 206 MediaLink Controller.
When possible in the following pages, line drawings are used to clarify steps
discussed in the text.
Lighting
Control
Screen
Control
Projector

Краткое содержание страницы № 2

33-644-01 A 07 01 MLC 206 Setup Guide, cont’d Step 1 — Computer Connection The MLC 206 must be connected to a PC in order to configure the controller. The configuration port, shown in the rear panel view below, is used for system control and for loading configuration and driver files into the MLC. 1. Connect a host computer to the MLC 206 Config port via the rear panel 9‑pin HD female RS‑232 connector. Use a serial cable with 9‑pin D connectors. RS-232 Configuration Port 9-pin Host De

Краткое содержание страницы № 3

3. To power the MLC, connect a 12 VDC power supply or an optional MediaLink Switcher (MLS) to the MLS/Power port, and connect the power supply or the switcher to a power source. A B MediaLink Switcher MLC/RS-232 +12VDC +12VDC Ground ( ) Ground ( ) B Receive (Rx) Transmit (Tx) B A Transmit (Tx) Receive (Rx) A A ground wire must be connected MLC 206 between the MLC and MLS. MLS/Power port A B MLS / Power MLC 206 powered by a MediaLink Switcher Ground ( ) +12 VDC input An external M

Краткое содержание страницы № 4

MLC 206 Setup Guide, cont’d Step 3 — Setting up projector control Device drivers allow the MLC 206 to control projectors and other source devices via RS‑232 or IR. It is strongly recommended that an RS-232 control (filenameRS1.mll) file for N controlling a projector be used whenever possible. To load a driver and configure the MLC 206: 1. Start the MediaLink Control Program. The appearance of the screens varies depending on which accessories (control modules and/or MediaLink Switcher)

Краткое содержание страницы № 5

3. Configure the buttons. Use the drop‑down box associated with each button to select the command to be issued or function to perform, as shown at right. Each configured button has a green or red dot on it. If a button has been previously configured, it will have a red (IR) or N green (RS-232) dot to indicate that an IR or RS-232 code has been associated with it. 4. Choose a volume control option. Select Projector if planning to use the projector display speakers or

Краткое содержание страницы № 6

MLC 206 Setup Guide, cont’d 3. Click on the button labeled Learn IR to Button. A dialog box appears indicating the button to which IR codes will be learned. d c 4. Click on OK to begin the learning process. During IR learning hold the device remote control 4 inches to 14 inches (10 cm to 36 cm) away from and directly in front of the MLC’s IR pickup device. DISPLAY POWER VCR DVD Laptop VOLUME MAX/ MIN Extron MediaLinM k C Lo C n t2 ro0 lle 6r MLC 206 4"–14" (10–36 cm) 1 2 3 4 5 6 7 8 9

Краткое содержание страницы № 7

33-644-01 A 07 01 Step 5 — Completing the installation 1. Save the configuration by selecting Save CONFIGURATION as..., and name it appropriately. 2. Connect the MLC 206 to the projector for RS‑232 projector control. a. Disconnect the power from the MLC (and the optional MediaLink Switcher, if applicable) and from the projector. b. Plug the 9‑ pin D connector of the RS‑ 232 projector control cable (such as an Extron UC 50’ cable) into the projector RS232 port. ‑ A cable adapter may be req

Краткое содержание страницы № 8

33-644-01 A 07 01 MLC 206 Setup Guide, cont’d The UC cable pin assignments are shown in the following illustration. To the To the MLC 206 projector Black 9 Grey 8 Purple 7 1 Blue 6 6 Green 5 Yellow 4 9 5 UC Cable Orange 3 Red 2 Brown 1 Connector Shell Shield Color Pin # UC 50', 100' Cable Color Codes 3. Install the IR Emitter(s) in the IR port as shown in the following illustration, and attach the head of each IR Emitter to an IR MLC-IR emitter_wiring_QS_112202.eps contr ‑ olled device (VCR,