Руководство по эксплуатации Chief Manufacturing F-Series Steel Stud FSA1018

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS
Instrucciones de instalación Istruzioni di installazione
Installationsanleitung Installatie-instructies
Instruções de Instalação Instructions d´installation
F-Series Steel Stud Installation Kit
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FSA1018

Краткое содержание страницы № 2

FSA1018 Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and Milestone AV Technologies, Inc., and its affiliated corporations follow all instructions can result in serious personal injury, and subsidiaries (collectively, "Milestone"), intend to make this damage to equipment, or voiding of factory warranty! It is the manual accurate and complete. However, Milestone makes no installer’s responsibility to make sure all components are claim that the information

Краткое содержание страницы № 3

T GL OG ER Installation Instructions FSA1018 TOOLS REQUIRED FOR INSTALLATION AND PARTS 1/2" (Ø13mm) (3/16") I/M x1 A (1) B (1) C (1) D (1) J (4) E (1) F (1) K (3) L (3) (1/4"-20) G (1) (1/4"-20 X 1 3/4") M (3) (1/4"-20 SNAPTOGGLE BB) H (1) (1/4"-20) N (1) (3/16") 3

Краткое содержание страницы № 4

FSA1018 Installation Instructions Site Requirements WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum reguirements for installation of display mounts onto a steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation. It should also be noted that no other equipment should be

Краткое содержание страницы № 5

Installation Instructions FSA1018 NOTE: Wall plate and hardware removed is not required Preparation of Existing Mount for steel stud installation. It may be discarded or If mount has previously been installed: kept for future use in a non-steel stud application. 1. Remove display from mount following instructions provided with mount. Assemble Swing Arm to Steel Stud Wall Plate 2. Remove mount from wall following instructions provided To assemble the mount: with mount. 3. Proceed to step 4. 1. Or

Краткое содержание страницы № 6

FSA1018 Installation Instructions Mount Installation After determining the site meets the installation requirements: Drywall 1. Identify desired mounting location on wall. 2. Using a stud finder or similar method locate studs. 3. Align mounting holes in mount with studs making sure Plastic Straps mounting holes are centered on studs. 4. Mark location of three mounting holes on wall. (See Figure 4) 5. Drill three 1/2" (Ø13mm) holes. (See Figure 4) 1/2" (Ø13mm) x3 (M) x3 Figure 5 5 7. Holding plas

Краткое содержание страницы № 7

Installation Instructions FSA1018 Steel Stud Drywall Plastic Cap Plastic Straps Anchor Metal Channel SIDE VIEW Figure 7 11. Place mount over anchors and align mounting holes in display mount with holes in anchors. (See Figure 8) 12. Place flat washer (K) onto button head capscrew (L). 13. Insert Phillips pan head capscrews (L) with flat washer (K) through mounting hole in display mount and into anchor (M) and tighten until flush against mount. DO NOT overtighten! WARNING: IMPROPER INSTALLATION C

Краткое содержание страницы № 8

FSA1018 Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 Chief Manufacturing, a division of F +31 (0)40 2668615 Milestone AV Technologies, Inc. Asia Pacific A Room 24F, Block D, Lily YinDu International Building 8804-000347 RevC LuoGang, BuJi Town, Shenzhen, CHINA. 2008 Milestone AV Technologies www.chiefmfg.com P +86-7