Краткое содержание страницы № 1
Installation Instructions / Warranty
Uno
38117XX1
Uno
38118XX1
Краткое содержание страницы № 2
Wall Mounted Single-Handle Lav Set with Base Plate 38117XX1 Wall Mounted Single-Handle Lav Set 38118XX1 38117XX1 38118XX1 Technical Data Max. flow rate: . gpm Max. water pressure: 147 psi Recommended pressure: 14.7 - 7 psi Test pressure: 3 psi Max. hot water temperature: 176° F* Recommended hot water temp.: 10° F - 140° F* Requires rough 38111181 (not included) For best results, Hansgrohe recommends installation by a licensed, professional plumber. These units may be used with an inst
Краткое содержание страницы № 3
Installation with 38111181 rough manufactured before 03/2004 Turn the water off at the supply before beginning this installation. 2. Remove the covers from the plaster shields (1). Trim the plaster shields so that they extend 1/16” out- side the surface of the finished wall (). Seal the wall around the plaster shield with waterproof sealant. 1. Use a 17 mm socket wrench to remove the spout plug. Use a 7 mm socket wrench to remove the cartridge assembly. Remove and discard the cup washers
Краткое содержание страницы № 4
Install the new cup washers and springs in the rough. Install the cartridge assembly. Installation with 38111181 rough manufactured after 04/2004 Turn the water off at the supply before beginning this installation. Remove the covers from the plaster shields. 2. Trim the plaster shields so that they extend 1/16” outside the surface of the finished wall. Seal the wall around the plaster shield with waterproof sealant. 1. Use a 17 mm socket wrench to remove the spout plug. Use a 7 mm socket
Краткое содержание страницы № 5
Install the cartridge and anti-twist device in the housing. Install the cup washers and springs in the rough. Install the cartridge assembly. Installation with all models: Push the handle over the cartridge stem. Tighten the handle screw with a mm Allen wrench. If you are installing 38117XX1, turn to page 6. If you are installing 38118XX1, turn to page 9.
Краткое содержание страницы № 6
Model 38117XX1 only: Measure the distance between the wall surface and the end of the handle (x). x If x is between 3 1/4” and 3 7/8”, select the two “A” sleeves (1 1/4”). A If x is between 3 7/8” - 4 3/8”, select the two “B” sleeves (7/8”). B If x is greater than 4 3/8”, select the two “C” sleeves (1/”). C 6 7/8” 1/” 1 1/4”
Краткое содержание страницы № 7
Connect the fixation nuts to the sleeves. Measure the distance from the rough to the outside surface of the finished wall (X) (1). 1. Add 1” to X. Cut the threaded end of the spout so that it is X + 1” long (). 2. X + 1” Push the baseplate against the wall (1). Thread the sleeves into the rough (). 2. 1. 7
Краткое содержание страницы № 8
Tighten the retaining nuts with the service key. Lightly lubricate the o-rings on the spout and handle escutcheons with the enclosed lubricant (1). Push the escutcheons onto the baseplate. 2. 1. Wrap the threads on the spout with Teflon tape (1). Install the spout (). Install the handle flange (3). 3. 1. 2. 8
Краткое содержание страницы № 9
Model 38118XX1 only: Measure the distance between the wall surface and the end of the handle (x). x If x is between 3 1/4” and 3 7/8”, select the “A” sleeve (1 1/4”). A If x is between 3 7/8” - 4 3/8”, select the “B” sleeve (7/8”). B If x is greater than 4 3/8”, select the “C” sleeve (1/”). C 1/” 7/8” 1 1/4”
Краткое содержание страницы № 10
Push the sealing ring into the handle escutcheon (1). Install the handle escutcheon onto the sleeve (). 1. 2. Push the sleeve / handle escutcheon assembly into place over the handle (1). Tighten it by rotating it 1. clockwise (). 2. Push the flange over the handle. 10
Краткое содержание страницы № 11
Measure the distance from the rough to the outside surface of the finished wall (X) (1). Add 1” to X. Cut the threaded end of the spout so that it is X + 1” long (). 1. 2. Install the spout escutcheon on the spout. Push the sealing ring into the spout escutcheon. Wrap the threads on the spout with Teflon tape (1). Install the spout (). 2. 1. 11
Краткое содержание страницы № 12
User Instructions on Pivot the handle up to turn the water on, down to turn it off. Pivot the handle to the left for warmer water, to the right for cooler water. off 38117XX1 6 8 3 1 4 11 7 1
Краткое содержание страницы № 13
38118XX1 6 8 10 1 11 7 Replacement Parts 1 flange 6 08 XX0 handle 100 XX0 3 escutcheon for handle 6 1 XX0 4 escutcheon for spout 613 XX0 baseplate 614 XX0 6 cartridge cpl. 633 000 7 aerator cpl. 6 11 XX0 8 fixing set 771000 escutcheon for spout 6 10XX0 10 escutcheon for handle 60 XX0 11 extension set (not included) 388 000 XX = color 00 = chrome 8 = brushed nickel 13
Краткое содержание страницы № 14
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning. Cleaning Materials for Faucets and Showers Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points when cleaning faucet
Краткое содержание страницы № 15
including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Hansgrohe and Commercial products, and (ii) for years, with respect to AXOR products. THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper maintenance, misuse, abuse, ne
Краткое содержание страницы № 16
Hansgrohe, Inc. • 140 Bluegrass Lakes Parkway • Alpharetta, GA 30004 Tel. 770 360-880 • Fax 770 360 887 www.hansgrohe-USA.com US - Installation Instructions • Part No. 000703 • Revised 07/007
