Краткое содержание страницы № 1
OPERATOR’S MANUAL OPERATOR’S MANUAL
OPERATOR’S MANUAL
OPERATOR’S MANUAL OPERATOR’S MANUAL
MODEL GC-STWC-CS61V
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TION FOR YOUR SCAG ACCESSORY. READ-
ING THIS MANUAL WILL PROVIDE YOU
WITH MAINTENANCE AND ADJUSTMENT
PROCEDURES TO KEEP YOUR ACCESSORY
PERFORMING TO MAXIMUM EFFICIENCY.
THE SPECIFIC MODELS THAT THIS BOOK
COVERS ARE CONTAINED ON THE INSIDE
COVER. BEFORE OPERATING YOUR MA-
CHINE, PLEASE READ ALL THE INFORMA-
TION ENCLO
Краткое содержание страницы № 2
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as the Operator's Manual that came with your
Краткое содержание страницы № 3
A replacement manual is available from your 1.1 INTRODUCTION authorized Scag Service Dealer or by contacting: Scag Power Equipment, Service Department at P.O. This manual has been prepared to provide the Box 152, Mayville, WI 53050. You may also contact information you need to correctly assemble, operate, us through our website at www.scag.com. The and maintain this grass catcher. Read it carefully and manual for this grass catcher can be downloaded by keep it for future reference. using the
Краткое содержание страницы № 4
5. To clean the hopper debris screen; 3. When dumping the hopper into a disposal area: A. Disengage the deck drive and allow all W WARNING ARNING moving parts to come to a complete stop. DO NOT DUMP CLIPPINGS IN A DISPOSAL AREA THAT IS BURNING B. Apply parking brake and shut off the engine. A. Disengage the deck drive, apply the parking C. Stand on the left side of the hopper brake and allow all moving parts to come to assembly. a complete stop. D. Unhook the debris screen latches and B. Pu
Краткое содержание страницы № 5
3.1 ASSEMBLY INSTRUCTIONS FOR 61" 4. Install the grass catcher pulley onto the spindle CUTTER DECK assembly. Apply loctite to both pulley setscrews and tighten. See Figure 3-1. -NOTE- Use the illustrated parts list as a part number 5. Remove the "Custom-Cut" and "Turbo" baffles reference when following the assembly from the cutter deck. Using the original hardware, install the new "Custom-Cut" and instructions. "Turbo" baffles. See Figure 3-2. 1. Remove all packaging materials. Lay ou
Краткое содержание страницы № 6
12. Install the hopper mounting brackets to the 7. Install the blower assembly to the mounting outside of the frame on the rear of the machine. bracket and secure with the mounting pin. See Figure 3-4. See Figure 3-5. Hopper 8. Align the blower assembly with the discharge Mounting Brackets opening of the cutter deck. Tighten the hardware for the mounting bracket. See Figure 3-4. Rear Frame Figure 4 A GC-STT Install Art 9. Install the quick pin through the rear hole in the discharge chute mount
Краткое содержание страницы № 7
14. Install the hose from the blower assembly adapter to the hopper hood and secure using the 8-1/2" clamps. 15. Using the weight support bar (p/n 451517) as a guide, identify the four corresponding mounting holes, and the existing hardware that will need to be removed in order to secure the weight support bar to the front of the machine as shown. See Figure 3-7. 16. Install one 7/16-14 x 1-3/4" hex head bolt into each of the four mounting holes in the weight support bar, and through the matchi
Краткое содержание страницы № 8
4.1 GRASS CATCHER REMOVAL INSTRUCTIONS Loosen 1. Prepare the machine so there is easy and safe Locking Remove Bolts access to the work area. Remove the key and Mounting maintain all safety related work procedures. Pins Always wear eye and hand protection. Loosen Locking Remove Bolts Mounting 2. Remove the rubber strap holding the adapter to Pins the blower assembly and the large quick pin securing the blower to the discharge mounting bracket. See Figure 4-1. 2005 GC-STC removal art 2-A 3
Краткое содержание страницы № 9
MAINTENANCE 5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS HOURS Break-In 8 20 40 100 200 500 Procedure Comments (First 10) X Check all hardware for tightness X Inspect hose and adapter X Check belt for proper alignment X Inspect fabric bags X *Check screen in hopper Remove debris from screen X Inspect hose and adapter X Inspect fabric bags X Check condition of blower X *Apply grease to blower bearings See figure below X Check belt for proper alignment * Perform these maintenance procedu
Краткое содержание страницы № 10
WARNING INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL DANGER ROTATING BLADES AND BLOWER Stop engine before cleaning or removing DO NOT OPERATE MOWER UNLESS GRASS CATCHER OR DISCHARGE GUARD IS INSTALLED GC-STWC-CS61V BLOWER HOUSING ASSEMBLY 9 10 11 8 12 45 48 4 1 2 14 3 13 11 9 11 7 10 47 10 14 44 27 14 12 11 15 43 16 42 14 17 26 41 39 40 18 34 15 19 14 25 17 28 35 20 21 41 38 22 17 35 27 23 5 24 46 14 24 14 29 6 30 33 32 37 31 31 35 35 2006 GC-STWC-61V Blower Assembly 35 34
Краткое содержание страницы № 11
GC-STWC-CS61V BLOWER HOUSING ASSEMBLY Ref. Part Ref. Part No. Number Description No. Number Description 1 04067-10 Pin, Ring 2-1/4" Long 27 04019-04 Nut, Serr. Flange 3/8-16 2 481547 Lanyard, Deck Height Pin 28 04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Gr. 8 3 04066-04 Quick Pin, 5/16" Dia. 29 483037 Decal, Danger 4 04001-21 Bolt, Hex Head 3/8-16 x 1-3/4" 30 461931 Blower Housing Weldment 5 481377 Decal, Blower 31 04003-12 Bolt, Carr. 5/16-18 x 3/4" Gr. 5 6 482080 Decal, Rotating Blowe
Краткое содержание страницы № 12
GC-STWC-CS61V BLOWER MOUNTING COMPONENTS UNDER SIDE OF VELOCITY-PLUS CUTTER DECK SHOWN 16 16 10 10 11 5 23 2 26 27 23 25 4 6 28 1 7 24 8 3 25 26 25 6 24 13 9 12 21 14 15 22 15 20 16 18 17 19 RIGHT SIDE OF CUTTER DECK SHOWN 2006 GC-STC-V BMC 10
Краткое содержание страницы № 13
GC-STWC-CS61V BLOWER MOUNTING COMPONENTS Ref. Part No. Number Description 1 483227 Belt Cover, GC-61V 2 04029-04 Wingnut, Plastic 3/8" Small 3 483223 Cap, Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461723 Adapter, Blower includes item #7 6 04040-14 Flatwasher, 1/4-.312 x .750 x .065 7 48137-04 Rubber Strap 7-3/4" 8 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4" 9 481625-01 Knob W/Stud, 3/8-16 x 1-1/4" 10 04064-15 Clevis Pin, 5/16 x 1-1/2" 11 04069-03 Pin, Rue Cotter 5/16 Dia. 12 04067-10 Pin, R
Краткое содержание страницы № 14
GC-STWC-CS61V HOPPER COMPONENTS 16 14 49 50 5 4 3 45 45 41 15 31 43 11 51 56 17 55 40 8 58 59 12 9 25 29 6 33 34 10 53 2 50 49 34 B 49 42 24 55 27 49 6 53 61 43 37 48 60 36 18 38 19 63 53 49 C 34 49 50 20 52 54 41 12 49 18 49 49 53 53 60 66 7 67 65 A 61 58 33 59 28 24 1 49 64 62 10 34 21 38 32 49 69 30 49 63 38 35 45 46 22 49 37 49 13 33 36 25 49 57 21 C 49 23 33 26 38 58 32 40 53 44 49 20 65 B 59 53 46 33 64 19 66 A 65 68 29 46 58 60 59 57 28 49 61 68A 49 61 35 49 46 72 26 37 37 60 2006 CSHOPP
Краткое содержание страницы № 15
GC-STWC-CS61V HOPPER COMPONENTS Ref. Part Ref. Part No. Number Description No. Number Description 1 483038 Hopper, GC-STC-CS 40 04001-77 Bolt, Hex Head 3/8-16 x 3-1/2" 2 482732 Door, GC-CS 41 04003-04 Bolt, Carriage 5/16-18 x 1" 3 461626 Sweeper Weldment, GC-CS 42 04010-01 Screw, #10-32 x 1/2" 4 482777 Pad, Rubber 43 04017-16 Cap Screw, 5/16-18 x 3/4" Serr. Flan. 5 04090-02 Pop Rivet, 3/16 x .652 44 04017-17 Cap Screw, 5/16-18 x 1" Serr. Flan. 6 423834 Plate, Stiffener 45 04019-03 Nu
Краткое содержание страницы № 16
GC-STWC-CS61V DECALS 482871 482871 482275 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENTS: 4,487,006 4,885,903 4,920,733 4,967,543 4,991,382 4,998,948 5,042,239 5,118,617 5,133,176 5,826,416 5,832,708 5,865,018 6,192,666 6,766,633 6,892,519 PATENTS PENDING 483044 481327 481377 483037 482080 482080 14
Краткое содержание страницы № 17
LIMITED WARRANTY- COMMERCIAL ACCESSORY Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the accessory to the dealer for warranty work
Краткое содержание страницы № 18
© 2005 PART NO. 03185 SCAG POWER EQUIPMENT PRINTED 8-2005 DIVISION OF METALCRAFT OF MAYVILLE, INC PRINTED IN USA www.scag.com
