Краткое содержание страницы № 1
Hole Locator HL-100
USA
Operating instructions
Краткое содержание страницы № 2
3 11/16” 3 1/4” 4 11/16” USA Operating manual: Should you have additional questions concerning this product’ s operation and use or care and maintance, please call our Customer Service number: 1.800.869.7460 U.S. and Canada 1. Main applications: The HL 100 hole locator is an easy-to-use point laser for aligning a series of holes in a straight line. The laser beam serves as a precise horizontal (level), incline /decline (slope) or vertical (plumb) reference point with a range up to 25m /75 ft.
Краткое содержание страницы № 3
2. Main components 8 3 13 4 12 10 1 11 5 2 9 5 7 6 (1) Laser beam emission aperture ON/OFF switch (2) Vertical setting dial (up/down) (3) Horizontal setting dial (left/right) (4) Small locking nut for holes from over 7/8” to 3” in diameter (20mm-75mm) (5) (6) Large locking nut for holes from 3 1/4” to 4 3/4”in diameter (80mm-120mm) (7) Adapter plate for holes over 3” (75 mm) Vial for horizontal leveling (8) Bulls eye vial for vertical leveling (9) Battery compartment cover (10) (11) Roll c
Краткое содержание страницы № 4
3. Method of operation: 3.1. Installation in joists / studs / panels I. Hole diameter ( small / large ) : 7 The HL 100 can be directly installed in holes from / ” to 3” in diameter using 8 the yellow locking nut (5). The large black locking nut (6) and the adapter 1 3 plate (7) are used for larger holes of 3 / ” to 4 / ” in diameter. Tighten the 4 4 locking nut until the tool is firmly in place. The conical shape centers the HL 100 in the hole. II. Material thickness ( min. / max. ) : 1 The HL
Краткое содержание страницы № 5
II. Aligning the laser dot horizontally (left - right): Mark the horizontal position on the second joist / stud. (No need to measure the vertical position). Turn on the laser(2). Dial the laser beam onto the mark by using the horizontal setting dial (4). ATTENTION : To ensure that the HL 100 is set up to point in the right direction, it is important that the lay out and drilling of the first joist/stud , as well as the horizontal measurement on the second joist/stud is done accurately. III. Ali
Краткое содержание страницы № 6
IV. Continue to drill The laser is now correctly aligned. Drill the second hole by setting the drill bit directly on the center of the laser dot location. Clear the debris from the hole, if necessary, to allow laser beam to pass through. The laser dot will now show the correct location of the hole to be drilled on the third joist / stud. Continue to drill the following joists / studs by using the center of the laser dot as the exact hole location. You may prefers to mark the center of the dot
Краткое содержание страницы № 7
Warning: This is a class IIIa laser. Do not look directly into the laser beam ! Keep this product away from children ! The goggles supplied with these units are not safety goggles. They enable you to see the laser beam more clearly in bright light conditions. 4. Checking the calibration The HL 100 has been designed for building site use and leaves our factory perfectly calibrated. As with any precision instrument, however, its calibration must be checked regularly. The unit should be checked bef
Краткое содержание страницы № 8
7. Technical data Laser type: Red diode laser, wavelength 650 nm Output: < 5 mW, Laser Class IIIa This product complies with the applicable requirements of 21CFR parts 1040.10 and 1040.11. Adjustment range: approx. ± 3° Accuracy: 1 Up-right position: ± 0,5 mm/m or ± / over 10 ft 16” 3 Over head position: ± 0,7 mm/m or ± / over 10 ft 32” 1 Plumb: ± 1 mm/m or ± / over 10 ft 8” Batteries: 2 x 1,5 V alkaline cell, size AA, LR6 Operating life: Approx. 48 hours Operating temperature range
Краткое содержание страницы № 9
STABILA Inc. 332 Industrial Drive South Elgin , IL 60177 1.800.869.7460 www.stabila.com 9
