Краткое содержание страницы № 1
300N Draft 802.11n Wireless USB Adapter
Model # AWLL6080
User’s Manual
Rev. 1.1
Краткое содержание страницы № 2
Table of Contents 1. Introduction................................................................................................................................. 3 1.1 Package Contents.................................................................................................................. 3 1.2 Features................................................................................................................................. 3 2. Installation...............................
Краткое содержание страницы № 3
1. Introduction Congratulations on your purchase of the 300N Draft 802.11n Wireless USB Adapter. The 300N USB Adapter provides wireless data rate of up to 300 Mbps* when used with other AirLink101® 300N wireless products. The high bandwidth combined with extended wireless coverage delivers fast and reliable connection for all of your networking applications. A full range of security features such as WEP, WPA-PSK, and WPA2-PSK provide the highest level of wireless network security. The
Краткое содержание страницы № 4
2. Installation 2.1 Install Driver & Utility This section provides instructions on how to install the 300N Draft 802.11n Wireless USB Adapter. The driver is installed along with the utility. Step 1 Insert the USB adapter into an available USB port and turn on your computer. Step 2 After turning on the computer, Windows will launch the Found New Hardware Wizard. The Found New Hardware Wizard appears differently depending on your operating system. Click Cancel to quit the wizard and
Краткое содержание страницы № 5
Note: If the Autorun screen doesn’t appear automatically, or if you get a blank white screen, go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your CD drive) and click OK. Windows Vista users: At this point, you may get a warning message like the one below. Make sure that you click Allow to continue with the installation. 5
Краткое содержание страницы № 6
Step 4 Click Next at the welcome screen. Step 5 Click Next to accept the default destination folder. 6
Краткое содержание страницы № 7
Step 6 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). For Windows Vista, click the Install this driver software anyway button when the security warning appears. 7
Краткое содержание страницы № 8
Step 7 Click Yes, I want to restart my computer now and then Finish to restart your computer. Step 8 After the computer is restarted, Windows will ask to connect to Windows 8
Краткое содержание страницы № 9
Update, select No, not this time and click Next. If this screen does not appear, you can skip to section 2.2. Step 9 Select Install the software automatically and click Next. 9
Краткое содержание страницы № 10
Step 10 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). 10
Краткое содержание страницы № 11
For Windows Vista, click the Install this driver software anyway button when the security warning appears. Step 11 Click Finish. 11
Краткое содержание страницы № 12
2.2 Verify Driver Installation To verify if the driver has been installed successfully, please perform the following steps. Step 1 Right-click on My Computer from your desktop and select Properties. Step 2 If you are using Windows XP/2000 select the Hardware tab, then click on Device Manager. If you are using Windows Vista, click on the device manager link on the left side of the screen. 12
Краткое содержание страницы № 13
Step 3 Expand Network adapters from the list and verify that AirLink101 300N Wireless USB Adapter is listed and no yellow question mark is beside it. If AirLink101 300N Wireless USB Adapter is not listed, or you see a yellow question mark beside it, you will need to reinstall the driver. 13
Краткое содержание страницы № 14
3. Configuring the Adapter This section describes how to connect your wireless adapter to a wireless network. Note to Windows XP Users: You must disable the Wireless Zero Configuration Utility in order to use the bundled Wireless Utility. Please follow the steps below to disable XP’s wireless utility. Windows Vista users can skip the following instructions and go to Step 1 Double-click on the Wireless Network Connection Icon in the system tray and then click on Properties or A
Краткое содержание страницы № 15
Step 1 To open the utility, double click on the Wireless Monitor icon in the system tray at the bottom right-hand corner of your screen. Step 2 Go to the AP List tab, select the SSID (Network Name) of the wireless network you wish to connect to, and click Connect. 15
Краткое содержание страницы № 16
If the network you are attempting to connect to is configured for encryption, you will see an orange lock icon next to the network. 16
Краткое содержание страницы № 17
When you click on it and click connect, a box will pop up requesting the wireless encryption key for the router. Enter the encryption key into the box and click OK. 17
Краткое содержание страницы № 18
Step 3 You should now be connected. You should see “Connected” in the top, right hand corner, and there will be a blue circle around the antenna icon next to the network name. Troubleshooting: If you are experiencing problems with the connection (unable to connect, low signal strength, slow connection speed, not working, unstable wireless connection) you will want to tune your router’s signal by changing channels on the router. You do not need to change the channel on the card,
Краткое содержание страницы № 19
4. Wireless Monitor This section describes the various functions of the Wireless Monitor that you can configure, including the settings of wireless encryption. 4.1 Wireless Information The Wireless Information box at the top of the window provides you with the status of the current connection, including signal, network name (SSID), IP Address and router channel. 19
Краткое содержание страницы № 20
4.2 AP List The AP List tab displays all the available wireless networks detected by the Wireless Adapter. Simply select the wireless network you wish to connect to and click Connect. If you have created multiple profiles, you can use the profile chooser at the bottom to select the specific profile you want to use. Then click Activate to enable that profile. 20
