Краткое содержание страницы № 1
User’s Manual
HSA 200S & HSA 200SE
HSA 200C & HSA 200CE
HSA 222S & HSA 222C
Hideaway Surface Access Products
68-695-01 Rev. H
08 08
© 2008 Extron Electronics. All rights reserved.
Краткое содержание страницы № 2
Precautions Safety Instructions • English Warning FCC Class A Notice Power sources � This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor. The third (grounding) pin is Note: This equipment has been tested and found to comply with the limits for a in the litera
Краткое содержание страницы № 3
Краткое содержание страницы № 4
Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About the Hideaway Surface Access Products ....... 1-2 About the Extender board line driver .................................. 1-4 Features ...................................................................................... 1-5 All models .............................................................................. 1-5 HSA 200CE and HSA 200SE models only .............................. 1-
Краткое содержание страницы № 5
Table of Contents, cont’d Appendix A � Reference Information ............................ A-1 HSA 200/222 Series Surface Access Products Specifications ......................................................................... A-2 HSA Part Numbers ................................................................ A-7 Included Parts ......................................................................... A-8 Routing Templates ............................................................... A-8 Repla
Краткое содержание страницы № 6
Introduction About the Hideaway Surface Access Products The Extron Hideaway HSA 200 series and HSA 222 series are furniture-mounted, architectural solutions for inconspicuous computer video and/or network access and control. The HSA 200C (figure 1-1) and HSA 200S (figure 1-2) provide: • One standard grounded AC receptacle The US versions have US power receptacles Figure 1-2 — HSA 200S hideaway enclosure The international versions have several different types of power receptacles available, i
Краткое содержание страницы № 7
Introduction The installed enclosures fit nearly flush within a table or podium Features top (figure 1-4), storing the connectors out of the way and out of sight. To access the connectors, the user presses down on the All models top of the enclosure, releasing a mechanical latch. A gas lift tips � UL/CUL listing the connectors into view. � CSA certification Projector � Easy access to connectors � Durable mechanical movement and latching mechanism Extron HSA 200C � Available in a variety of sur
Краткое содержание страницы № 8
Introduction HSA 200/222 Series Surface Access Products Chapter Two 2 Installation Installation Overview Preparing the Routing Template Preparing the Table and Mounting the Enclosure Underside Features and Cabling Connections Front Panel Connectors Pre-installation Testing and Troubleshooting (HSA 200CE and HSA 200SE Models Only) 1-6 HSA 200/222 Series � Introduction
Краткое содержание страницы № 9
Width of Mounting Surface Installation Installation Overview Preparing the Routing Template Install and set up the HSA surface access enclosures as follows: Extron provides a metal template for each HSA model at no charge. Appendix A lists the HSA 200 and HSA 222 template 1 If you have an unprepared mounting template, prepare part numbers. Extron recommends using this template as a the template. See “Preparing the Routing Template” in guide to cut the hole in the table where the HSA will be t
Краткое содержание страницы № 10
Installation, cont’d Preparing the Table and Mounting the Enclosure The preferred and recommended method for preparing the table is to use the appropriate Extron routing template and a router. The templates are available at no cost; see the part numbers for the templates in appendix A, “Reference Information”. For an HSA 200C, HSA 200CE, or HSA 222C unit (US version only), another preferred method is to use a 6" hole saw. Alternatively, for any model, you can use a paper cut-out template (see a
Краткое содержание страницы № 11
CAT6 Installation, cont’d 2. Remove the plastic strips that protect the corners of the Preparing the table with a hole saw (HSA 200C, enclosure. If a sticky residue remains, remove it with an HSA 200CE, or HSA 222C—US version only) appropriate metal cleaning product. 1. Locate the desired mounting location on the tabletop or Do not use isopropyl alcohol or other solvents to clean CAUTION other installation surface. Mark the 6" circle, then find the the HSA. Strong solvents will ruin some fini
Краткое содержание страницы № 12
Installation, cont’d 5. Snugly tighten the Philips head screws on the screw All HSA 200 models only clamps to secure the enclosure to the surface. AC power outlet — Use this AC connector to: 1 Overtightening the Philips head screws on the screw CAUTION � Plug in an external power supply to power the Extender clamps can bend the clamp’s horizontal flange. board on the HSA 200CE or HSA 200SE. 6. Tighten the locking thumbscrews on the screw clamps to � Provide AC power (5 amps max.) for loop throug
Краткое содержание страницы № 13
Installation, cont’d All HSA 200 and HSA 222 models Latch locking screws — These screws secure the latching 7 mechanism to the enclosure. They must be loosened in order to 4 Screw clamp bracket/screw clamp — These two brackets/ adjust the top surface (see “Adjusting the Top Panel” in clamps hold the enclosure firmly in place in the mounting hole. 8 chapter 3) with the top surface adjustment screw . 5 AC power input connection — Connect this cord to the power Top surface adjustment screw — After
Краткое содержание страницы № 14
Installation, cont’d Do not tin the stripped power supply leads. Tinned Power connector wiring wires are not as secure in the captive screw terminals 1. See figure 2-10. Plug the input connector of the included and could pull out. 100-240 VAC, 50/60Hz, 12 VDC power supply into the AC 1 power outlet on the underside of the enclosure ( on The two power cord wires must be kept separate figure 2-5). while the power supply is plugged in. Remove power before continuing. To verify the polarity befor
Краткое содержание страницы № 15
Installation, cont’d The Universal AC outlet is fully compatible with Europlug, British, Indian, Danish, and Italian plug types. See the universal AC outlet guide on the Extron Web site, www.extron.com, for compatibility details on all plug types. 5A 5B Front View 2 Computer video input (HSA 200 models only) — Plug the VGA-UXGA output from a computer into this 15-pin HD female connector. 6A 6B Audio input connector (HSA 200 models only) — Plug a 3 3.5 mm stereo plug into this jack for unbalanc
Краткое содержание страницы № 16
Installation, cont’d Pre-installation Testing and Troubleshooting HSA 200/222 Series Surface Access Products (HSA 200CE and HSA 200SE Models Only) Before installing an HSA 200 with an Extender line driver into furniture, test the system to make sure that the connections and settings are correct. 1. Apply power to the line driver. The power/signal LED on the line driver will light to indicate that the line driver is receiving power. If the LED does not light, check the wiring at both the line dr
Краткое содержание страницы № 17
Maintenance and Modifications The most probable corrective maintenance procedures for your The surfaces of the HSA enclosure have screws and other HSA 200 or HSA 222 are leveling the top surface and replacing protrusions that could damage fine furniture. Do not the gas lifts. Most of the maintenance procedures require rest the enclosure on unprotected furniture. removing the surface mount enclosure from the table. 5. Perform the desired maintenance procedure. 6. If the surface is not level, ad
Краткое содержание страницы № 18
Maintenance and Modifications, cont’d 2. (HSA 222 models only) Remove the four Philips head 3. (HSA 222 models only) Disconnect both RJ-45 connectors screws from the front access panel (figure 3-1). Retain the from the underside of the enclosure by simultaneously screws. Lift the panel away from the enclosure. performing steps 3a and 3b: a. With a Tweeker in one hand, reach through the small access hole in the front of the enclosure (figure 3-2) and gently pry outward on the front of the RJ-45
Краткое содержание страницы № 19
AUDIO HSA 200 240 - 50/60 Hz 5A Maintenance and Modifications, cont’d 4. Remove the four 1/16" hex head screws on the right and 8. Snap the internal RJ-45 connector onto the back of the front left sides of the front panel (figure 3-3). Retain the screws. panel enclosure bezel plug-in. Lift the panel away from the enclosure. 9. (HSA 222 models only) Reach your hand through the Figure 3-3 shows an HSA 200 model. Removing the front panel access hole and snap the lower internal RJ-45 front panel f
Краткое содержание страницы № 20
AUDIO HSA 200 240 - 50/60 Hz 5A Maintenance and Modifications, cont’d 5. Turn the surface mount enclosure onto its back side and Replacing the Gas Lift open the top panel. The gas lift that raises the HSA surface is rated for 100,000 With the gas lift removed, the top panel must be opening and closing cycles. Replace the gas lift as follows: manually lifted. Ensure that AC power is disconnected before 6. (HSA 200 models only) Remove the four 1/16" hex head servicing the HSA unit. screws on the
