Краткое содержание страницы № 1
NPort 5400 Series
User’s Manual
Sixth Edition, March 2007
www.moxa.com/product
Moxa Technologies Co., Ltd.
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231
Web: www.moxa.com
MOXA Technical Support
Worldwide: support@moxa.com
The Americas: support@usa.moxa.com
Краткое содержание страницы № 2
NPort 5400 Series User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright © 2007 Moxa Technologies Co., Ltd. All rights reserved. Reproduction without permission is prohibited. Trademarks MOXA is a registered trademark of The MOXA Group. All other trademarks or registered marks in this manual belong to their respective manufacturers. Disclai
Краткое содержание страницы № 3
Table of Contents Chapter 1 Introduction ..................................................................................... 1-1 Overview........................................................................................................1-2 Package Checklist .........................................................................................1-2 Product Features ...........................................................................................1-2 Product Specifications.
Краткое содержание страницы № 4
Auto warning: E-mail and SNMP trap ...............................................5-27 Event Type ........................................................................................5-28 Monitor.........................................................................................................5-30 Monitor Line.......................................................................................5-30 Monitor Async.....................................................................
Краткое содержание страницы № 5
1 1 Chapter 1 Introduction Welcome to the MOXA NPort 5400 Series of advanced serial device servers, which make it easy to enable network operation of your serial devices. All device servers in the series come with four serial ports. On the NPort 5410, the serial ports are RS-232 ports; on the NPort 5430/5430I, the serial ports are RS-422/485 ports; on the NPort 5450/5450I, the serial ports are RS-232/422/485 ports. The following topics are covered in this chapter: Overview Package
Краткое содержание страницы № 6
NPort 5400 Series User’s Manual Introduction Overview NPort 5400 Series device servers are designed to make your industrial serial devices Internet ready instantly. The compact size of NPort 5400 device servers makes them the ideal choice for connecting RS-232/422/485 serial devices—such as PLCs, meters, and sensors—to an IP-based Ethernet LAN, making it possible for your software to access serial devices anywhere over a local LAN or the Internet. NPort 5400 serial device servers ensure t
Краткое содержание страницы № 7
NPort 5400 Series User’s Manual Introduction Product Specifications LAN Ethernet 10/100 Mbps, RJ45 Protection Built-in 1.5 KV magnetic isolation NPort 5410 Serial Interface Interface RS-232 No. of Ports 4 Port Type DB9 Male Signals TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND Serial Line Protection 15 KV ESD for all signals NPort 5430/5430I Serial Interface Interface RS-422/485 No. of Ports 4 Port Type Terminal Block Signals RS-422: Tx+, Tx-, Rx+, Rx-, GND RS-485 (2-wire): Data+
Краткое содержание страницы № 8
NPort 5400 Series User’s Manual Introduction Serial Communication Parameters Parity None, Even, Odd, Space, Mark Data Bits 5, 6, 7, 8 Stop Bit 1, 1.5, 2 Flow Control RTS/CTS, XON/XOFF, DSR/DTR (NPort 5410, 5450, and 5450I only) Transmission Speed 50 bps to 921.6 Kbps Software Features Protocols ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP, HTTP, SMTP, SNTP, Rtelnet, ARP Utilities NPort Administrator for Windows 95/98/ME/NT/2000/XP/2003 OS Driver Support Windows Real COM dr
Краткое содержание страницы № 9
2 2 Chapter 2 Getting Started This chapter includes information about installing NPort 5400 Series device servers. The following topics are covered: Panel Layout Connecting the Hardware Wiring Requirements Connecting the Power Grounding the NPort 5400 Connecting to the Network Connecting to a Serial Device LED Indicators
Краткое содержание страницы № 10
NPort 5400 Series User’s Manual Getting Started Panel Layout NPort 5410/5450/5450I Power input RESET V+ V- LAN RJ45 10/100 Mbps Ethernet port Terminal Block power input 5410 NP5410_61405 192.168.127.254 Serial Device Server Port 1 Port 2 Port 3 Port 4 RS-232 RS-232 RS-232 RS-232 Indicator LEDs Input buttons LCM display panel Male DB9 serial port NPort 5430/5430I Power input RESET V+ V- LAN RJ45 10/100 Mbps Ethernet port Terminal Block power input 5430 NP5430_61405 192.168.127.254 Serial D
Краткое содержание страницы № 11
NPort 5400 Series User’s Manual Getting Started Connecting the Hardware This section describes how to connect the NPort 5400 to serial devices for first time testing purposes. We cover Wiring Requirements, Connecting the Power, Grounding the NPort 5400 Series, Connecting to the Network, Connecting to a Serial Device, and LED Indicators. Wiring Requirements ATTENTION Safety First! Be sure to disconnect the power cord before installing and/or wiring your NPort 5400. Wiring Caution! Cal
Краткое содержание страницы № 12
NPort 5400 Series User’s Manual Getting Started ATTENTION This product is intended to be mounted to a well-grounded mounting surface such as a metal panel. SG: The Shielded Ground (sometimes called Protected Ground) contact is the left most contact of the 3-pin power terminal block connector when viewed from the angle shown here. Connect the SG wire to an appropriate grounded metal surface. Connecting to the Network Connect one end of the Ethernet cable to the NPort 5400’s 10
Краткое содержание страницы № 13
NPort 5400 Series User’s Manual Getting Started Adjustable Pull High/low Resistors for the RS-485 Port In some critical environments, you may need to add termination resistors to prevent the reflection of serial signals. When using termination resistors, it is important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. Since there is no resistor value that works for every environment, DIP switches are used to set the pull high/low resistor values f
Краткое содержание страницы № 14
3 3 Chapter 3 Initial IP Address Configuration When setting up your NPort 5410/5430/5430I/5450/5450I for the first time, the first thing you should do is configuring the IP address. This chapter introduces the method to configure the NPort’s IP address. Select one of the initial IP Address configuration methods to configure the NPort’s IP Address. For more details about network settings, see the Network Settings section from Chapter 5, Web Console Configuration. This chapter includes t
Краткое содержание страницы № 15
NPort 5400 Series User’s Manual Initial IP Address Configuration Initializing the NPort’s IP Address 1. Determine whether your NPort needs to use a Static IP or Dynamic IP (either DHCP or BOOTP application). 2. If the NPort is used in a Static IP environment, you can use LCM Display, NPort Administration Suite, ARP, Web Console, or Telnet Console to configure the new IP address. 3. If the NPort is used in a Dynamic IP environment, you can use LCM Display, NPort Administration suite, Web C
Краткое содержание страницы № 16
NPort 5400 Series User’s Manual Initial IP Address Configuration There are four push buttons on the NPort’s nameplate. Going from left to right, the buttons are: Button Name Action MENU menu activates the main menu, or returns to a lower level scrolls up through a list of items shown on the LCM panel’s second line up cursor down cursor scrolls down through a list of items shown on the LCM panel’s second line SEL select selects the option listed on the LCM panel’s second line The butt
Краткое содержание страницы № 17
NPort 5400 Series User’s Manual Initial IP Address Configuration Main Menu Server Serial number D setting Server name C Firmware ver D Model name D Network Ethernet status D setting MAC address D IP config C IP address C Netmask C Gateway C DNS server 1 C DNS server 2 C Serial set Select port C Baud rate C Data bit C Stop bit C Parity C Flow control C Tx/Rx fifo C Interface C Tx/Rx bytes D Line status D Op Mode set Select port C Select mode C [mode] Real COM TCP
Краткое содержание страницы № 18
NPort 5400 Series User’s Manual Initial IP Address Configuration The second type of configurable option is when there are only a small number of options from which to choose (although only one option will be visible at a time). Consider the PARITY attribute under PORT SETTING as an example. Follow the tree graph to arrive at the following PARITY screen. The first option, NONE, is displayed, with a down arrow all the way to the right. This is an indication that there are other options from w
Краткое содержание страницы № 19
NPort 5400 Series User’s Manual Initial IP Address Configuration Take the following steps to use ARP to configure the IP address: 1. Obtain a valid IP address for your NPort from your network administrator. 2. Obtain the NPort’s MAC address from the label on its bottom panel. 3. Execute the ‘arp -s’ command from your computer’s MS-DOS prompt by typing: arp –s 192.168.200.100 00-90-E8-xx-xx-xx This is where 192.168.200.100 is the new IP address and 00-90-E8-xx-xx-xx is the MAC address for
Краткое содержание страницы № 20
NPort 5400 Series User’s Manual Initial IP Address Configuration 4. Type 2 to select Network settings, and then press Enter. 5. Type 1 to select IP address and then press Enter. 6. Use the Backspace key to erase the current IP address, type in the new IP address, and then press Enter. 3-7
