Краткое содержание страницы № 1
SmartSwitch 9000
9E106-06
Ethernet Switch Module
User’s Guide
Краткое содержание страницы № 2
Краткое содержание страницы № 3
Notice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATS
Краткое содержание страницы № 4
Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable pr
Краткое содержание страницы № 5
Notice DOC Notice This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. iii
Краткое содержание страницы № 6
Notice iv
Краткое содержание страницы № 7
Contents Chapter 1 Introduction Features........................................................................................................................... 1-2 Related Manuals............................................................................................................ 1-5 Getting Help .................................................................................................................. 1-5 Chapter 2 Installing the 9E106-06 Module Installing EPIMs ...
Краткое содержание страницы № 8
Contents Appendix A EPIMs EPIM-T...........................................................................................................................A-1 EPIM-F1 and EPIM-F2.................................................................................................A-2 EPIM-F3 .........................................................................................................................A-3 EPIM-C..............................................................................
Краткое содержание страницы № 9
Chapter 1 Introduction The 9E106-06 is a multi-port Ethernet Switch Module for the SmartSwitch 9000 that provides high speed IEEE 802.1D compliant bridging and SecureFast™ Switching (SFS). ® Each 9E106-06 is equipped with two advanced Intel i960 RISC microprocessors. One processor provides the module’s SNMP protocol stack for both IETF and Enterprise MIB extensions. Additional higher-level management services such as RMON and Distributed LAN Monitor (DLM) are also provided. The other
Краткое содержание страницы № 10
Introduction Features Processors ® The 9E106-06 is equipped with dual advanced Intel i960 RISC microprocessors. One processor provides a platform for all management applications, such as Spanning Tree, RMON, IETF and Enterprise MIB support. This network management information is available through a variety of methods. All SNMP based information is accessible either via an in-band (front panel port), side-band (SMB-10), or out-of-band via the Environmental Module’s (EM) COM port
Краткое содержание страницы № 11
Introduction The FNB backplane connection is a fixed connection to FNB-1 or FNB-2. This connection allows the 9E106-06 to communicate with other SmartSwitch 9000 modules supporting various LAN technologies including: Token Ring, FDDI, Ethernet, WAN and ATM. Bridging/SecureFast™ Switching 9E106-06 operates in two modes, as a traditional bridge, or as a SecureFast Switch. In the traditional bridge mode, the 9E106-06 makes filtering/forwarding decisions based on frame destination addr
Краткое содержание страницы № 12
Introduction ETHERNET 9E106-06 SMB CPU FNB Figure 1-1. The 9E106-06 1-4
Краткое содержание страницы № 13
Introduction Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual. SmartSwitch 9000 Installation Guide SmartSwitch 9000 Operations Guide SmartSwitch 9000 9C300-1 Environmental Module User’s Guide SmartSwitch 9000 9C214-1 AC Power Supply User’s Guide SmartSwitch 9000 Local Management User’s Guide INB Terminator Modules Installation Guide Getting Help If you need additional support related to this device,
Краткое содержание страницы № 14
Introduction 1-6
Краткое содержание страницы № 15
Chapter 2 Installing the 9E106-06 Module The 9E106-06 Module may be installed in any of the 14 slots available in the SmartSwitch 9000 chassis. To install the 9E106-06 Module, follow the steps below: 1. Remove the blank panel covering the slot that the module is being mounted in. All other slots must be covered, if modules are not being installed, to ensure proper airflow and cooling. 2. Carefully remove the module from the shipping box. (Save the box and packing materials in the event t
Краткое содержание страницы № 16
Installing the 9E106-06 Module Plastic Tab Jack for ESD Wrist Strap Metal Back-Panel Module Module Guides Figure 2-1. Installing the 9E106-06 Module Ensure that the module is between the module guides. Lock down the top and bottom plastic tabs at the same time, applying even pressure. WARNING 2-2
Краткое содержание страницы № 17
Installing the 9E106-06 Module Installing EPIMs This section contains procedures on how to add/replace an Ethernet Port Interface Module (EPIM). After installing the EPIM, refer to Appendix A to verify proper EPIM operation. Observe all static precautions while handling EPIMs. ! CAUTION EPIM Revisions Revision numbers are located on the EPIM’s Printed Circuit Board directly following the Part Number as shown in Figure 2-2. Table 2-1 lists the required board revision for each EPIM. EPI
Краткое содержание страницы № 18
Installing the 9E106-06 Module Table 2-1. EPIM Board Revisions EPIM EPIM BOARD REVISION EPIM-T 04 or greater EPIM-F2 05 or greater EPIM-F1 05 or greater EPIM-F3 02 or greater EPIM-C 05 or greater EPIM-A Not Applicable EPIM-X 02 or greater Installing the EPIM To install an EPIM: When removing an EPIM, make sure to pull the module straight out so as not to NOTE damage the connector. 1. Remove the coverplate or the EPIM (whichever applies). 2. Slide your new EPIM into place, making sure th
Краткое содержание страницы № 19
Installing the 9E106-06 Module E N E T 1 Mounting Screw E N E T 2 EPIM Figure 2-3. Installing an EPIM The Reset Switch The Reset Switch is located on the front panel, under the top plastic tab, as shown in Figure 2-4. It serves two functions: • Pressing the Reset Switch twice within three seconds resets the module. • Pressing and holding the switch on for three or more seconds causes the module to shutdown. Pressing and holding the switch again for three seconds restarts the module. SNM
Краткое содержание страницы № 20
Installing the 9E106-06 Module Reset Switch SMB CPU Figure 2-4. The Reset Switch User-Accessible Components Figure 2-5 shows the various components that are accessible to the user. These consist of an eight-switch DIP switch (explained in the next section), replaceable PROMs and sockets for RAM. These will be used for future upgrades. Instructions for installing the components will be supplied with the upgrade kit. 2-6
