Руководство по эксплуатации American Standard PORTSMOUTH 7420.101

Краткое содержание страницы № 1

Installation
Instructions
7415.101
7420.101
PORTSMOUTH™
7415.101
MONOBLOCK LAVATORY
Series
FAUCET with Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only
on American Standard faucets.
7420.101
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
Certified to comply with ANSI A112.18.1
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed

Краткое содержание страницы № 2

POP-UP DRAIN 2 Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN DRAIN POP-UP (3). 3 BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 4 REMOVE FLANGE 3 Fig. A. Fig. B. 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. 4 2 3 INSTALL DRAIN FROM TIGHTEN LOCKNUT 4 5

Краткое содержание страницы № 3

ATTACH CABLE CONNECTOR 7 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. CHECK OPERATION OF POP-UP 8 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 2 MAKE WATER SUP

Краткое содержание страницы № 4

ON OFF TEST INSTALLED FITTING 10 1 COLD With HANDLE (1) in OFF position, turn on WATER HOT SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). 4 Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3). 3 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting 5 section in these instructions. Re

Краткое содержание страницы № 5

Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. C

Краткое содержание страницы № 6

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice Fig. G. that the Loop is on one side of the Stopper. Fig. G. LOGO To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper s

Краткое содержание страницы № 7

PORTSMOUTH™ Momoblock Lavatory Faucet with Speed Connect™ Drain M962951-YYY0A HANDLE KIT M917161-0070A MODEL NUMBERS SET SCREW 7415.101 Series M907063-YYY0A CARTRIDGE COVER M904528-0070A CARTRIDGE NUT A918462-0070A SCREW M962682-0070A CARTRIDGE M962544-YYY0A M962810-YYY0A STOPPER POP-UP ROD ASSEMBLY M952430-0070A M952425-YYY0A CABLE ASSEMBLY DRAIN ASSEMBLY M962457-YYY0A M922881-YYY0A FLANGE AERATOR ASSEMBLY M922872-0070A 911903-0070A CAM SEAT INSERT SEAL M962552-0070A CAM ASSEMBLY 7420101P M913