Руководство по эксплуатации American Standard SERIN 2064.4

Краткое содержание страницы № 1

Installation
Instructions
™
2064.400
SERIN
Bidet Faucet and Transfer Valve with
Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Certified to comply with ANSI A112.18.1
M968924 Rev.1.3
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with

Краткое содержание страницы № 2

POP-UP DRAIN 3 Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 DRAIN Remove CARDBOARD SPACER (2) from under BODY DRAIN POP-UP (3). 3 Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 4 2 REMOVE FLANGE Fig. A. Fig. B. 4 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. 4 2 3 INSTALL DRAIN FROM TIGHTEN LOCKNUT 5 6

Краткое содержание страницы № 3

ATTACH CABLE 8 CONNECTOR Fig. A. Fig. B. Fig. C. DOWN POP-UP KNOB (1) must be fully down. Fig. A. 1 Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. B. Your new POP-UP DRAIN installation is now complete. 2 Fig. C. 1-1/4” O.D. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. C. CHECK OPERATION OF POP-UP 9 5 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 4 1 3 Note: If STOPPER (2) does not open and close properly then refer to the “

Краткое содержание страницы № 4

INSTALL HANDLES 11 Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without a spline is facing up. See figure "A". Tighten THREAD ON TO DECK STEM SCREW (3) to secure ADAPTER (1). ADAPTER 4 Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4). TOP Thread LEVER HANDLE ASSEMBLY (4) onto ESCUTCHEON (5) 1 until snug against mounting surface. 3 Figure "A" 2 SPLINE END DOWN 5 TEST INSTALLED FITTING 12 OUTLINE OF B

Краткое содержание страницы № 5

Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. C

Краткое содержание страницы № 6

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice Fig. G. that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate LOGO Stopper s

Краткое содержание страницы № 7

™ SERIN BIDET FITTING MODEL NUMBERS 2064.400 M962508-YYY0A POP-UP ROD M950245-YYY0A HANDLE ASSEMBLY M962414-YYY0A 918428-0070A ESCUTCHEON KIT M962481-YYY0A HANDLE SCREW LIFT ROD GUIDE M962182-YYYOA 918555-0070A HANDLE HANDLE SCREW 918049-0070A ADAPTER 033772-0070A 923348-0070A 994053-0070A TEE AND HOSE KIT HANDLE ADAPTER CARTRIDGE (INCLUDING SEALS) 030257-YYYOA M961634-0070A ESCUTCHEON KIT VALVE MTG. KIT 030281-0070A TRANSFER VALVE MOUNTING KIT 060463-0070A 953800-0070A ADAPTER KIT TRANSFER VAL