Краткое содержание страницы № 1
ESPAÑOL: PÁGINA 17
FRANÇAISE : PAGE 31
Instruction
manual
Router
MODEL
100
IMPORTANT
To learn more about Porter-Cable
Please make certain that the person who is
visit our website at:
to use this equipment carefully reads and
understands these instructions before
http://www.porter-cable.com
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ___________________________
Краткое содержание страницы № 2
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . .6 CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 FUNCTIONAL DESCRIPTION . . .
Краткое содержание страницы № 3
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury. indicates a potentially hazardous situ
Краткое содержание страницы № 4
GENERAL SAFETY RULES Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the pre
Краткое содержание страницы № 5
GENERAL SAFETY RULES continued d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair
Краткое содержание страницы № 6
ADDITIONAL SPECIFIC SAFETY RULES 1. HOLD POWER TOOL BY INSULATED GRIPPING SURFACES WHEN PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. USE CLAMPS OR OTHER PRACTICAL WAY TO SECURE AND SUPPORT THEWORKPIECE TO A STABLE PLATFORM. Holding the work by hand or against your body is unstable and may lead to loss of control. 3. DISCONNECT TOOL FROM POWER SOURCE
Краткое содержание страницы № 7
SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µF ........................ microfarads l ........................ litres g ........................ grams kg ........................ kilograms bar ........................ bars Pa ........................ pascals h ........................ hours min .......................
Краткое содержание страницы № 8
MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to the specification plate on your tool for proper voltage and current rating. Do not operate your tool on a current on which the voltage is not within correct limits. Do not operate tools rated A.C. only on D.C. current. To do so ma
Краткое содержание страницы № 9
CARTON CONTENTS * Router * Wrenches (2) FUNCTIONAL DESCRIPTION FOREWORD The router is one of the most useful tools in the woodworking field. It may be used for many cutting and shaping operations such as slotting, mortising, dadoing, grooving, rabbeting, corner-rounding, beading, dovetailing, veining, inlay work, etc. OPERATION NOTE: This tool is shipped completely assembled. No assembly time or tools are required. SELECTING THE BIT 1 This Router comes with a /4" split type collet which accomm
Краткое содержание страницы № 10
1. To remove motor unit from base unit: Open the clamp (A) Fig. 1. While holding base, turn power unit COUNTERCLOCKWISE until lower pin (B) in motor housing is disengaged from groove in base. Lift power unit free from base unit. 2. Clean and insert shank of bit into collet until shank bottoms, then back it out approximately 1/16". Do not use router bits with a diameter in excess of 1.5" in this tool. 3. Lay power unit on its side on bench with the collet pointing AWAY from you. 4. Place one wren
Краткое содержание страницы № 11
F B D E C A Fig. 3A Fig. 3B NOTE: Setting the index line to 1/4" on the ring means the cutting edge of the bit is exposed 1/4" below the base. CONNECTING TO POWER SOURCE Before connecting tool to power source ALWAYS MAKE SURE SWITCH IS IN THE “OFF” POSITION. Also check that the power circuit is the same as that shown on specification plate of the router. STARTING AND STOPPING THE MOTOR Before starting the router, make sure that the bit is clear of the workpiece and foreign objects. Keep a firm g
Краткое содержание страницы № 12
USING THE ROUTER IMPORTANT: Before using your router, consider the kind and total amount of material to be removed. Depending on the workpiece, more than one cut may be necessary to avoid overloading the motor. Before beginning the cut on the actual workpiece, make a sample cut on a piece of scrap lumber to show exactly how the cut will look, as well as enable you to check dimensions. Always be sure that the work is rigidly clamped or otherwise secured before making a cut. Generally speaking, wh
Краткое содержание страницы № 13
TEMPLET GUIDES A wide variety of templet guides is available for use in pattern and templet routing operations. Fig. 7 shows a typical combination bit, templet guide, and locknut. DISCONNECT TOOL FROM POWER SOURCE. To install, insert templet guide in center hole of router base and secure in place with the locknut. BEFORE CONNECTING TOOL TO POWER SOURCE, install the bit, adjust the depth of cut, and rotate the router chuck by hand. Make sure that the bit or collet do not contact templet guide. B
Краткое содержание страницы № 14
MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. FAILURE TO START Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit brea
Краткое содержание страницы № 15
ACCESSORIES A complete line of accessories is available from your Porter-Cable•Delta Supplier, Porter-Cable•Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Porter-Cable•Delta have not been tested with this product, use of such accessories could be hazardous. For safest operation, only Porter-Cable•Delta recommended acces
Краткое содержание страницы № 16
NOTES 16
Краткое содержание страницы № 17
ENGLISH: PAGE 1 FRANÇAISE : PAGE 31 Manual de Contorneador (Ráuter) Instrucciones MODELO 100 IMPORTANTE Para obtener más información Asegúrese de que la persona que va a usar sobre Porter-Cable, esta herramienta lea cuidadosamente y visite nuestro sitio web en: comprenda estas instrucciones antes de empezar a operarla. http://www.porter-cable.com La placa de Modelo y de Número de Serie está localizada en la caja principal de la herramienta. Anote estos números en las líneas de abajo y guárdelo
Краткое содержание страницы № 18
INSTRUCCIONES DE SEGURIDAD IMPORTANTES Lea y entienda todas advertencias y las instrucciones operadoras antes de utilizar cualquier instrumento o el equipo. Cuando se usa instrumentos o equipo, las precauciones básicas de la seguridad siempre se deben seguir para reducir el riesgo de la herida personal. La operación impropia, la conservación o la modificación de instrumentos o equipo podrían tener como resultado el daño grave de la herida y la propiedad. Hay ciertas aplicaciones para que equipaa
Краткое содержание страницы № 19
NORMAS GENERALES DE SEGURIDAD Lea todas las instrucciones. Si no se siguen todas las instrucciones que aparecen a continuación, el resultado podría ser sacudidas eléctricas, incendio y/o lesiones graves. La expresión "herramienta mecánica" en todas las advertencias que aparecen a continuación se refiere a su herramienta mecánica alimentada por la red eléctrica (herramienta alámbrica) o su herramienta mecánica alimentada por baterías (herramienta inalámbrica). GUARDE ESTAS INSTRUCCIONES 1) Seguri
Краткое содержание страницы № 20
(continuación) NORMAS GENERALES DE SEGURIDAD d)Quite todas las llaves de ajuste o de tuerca antes de encender la herramienta mecánica. Una llave de tuerca o de ajuste que se deje colocada en una pieza giratoria de la herramienta mecánica podría causar lesiones corporales. e)No intente alcanzar demasiado lejos. Mantenga un apoyo de los pies y un equilibrio apropiados en todo momento. Esto permite controlar mejor la herramienta mecánica en situaciones inesperadas. f) Vístase adecuadamente. N
