Руководство по эксплуатации Lanzar Car Audio 2055D

Краткое содержание страницы № 1

USER’S MANUAL
AMPLIFIERS: AMPLIFIERS:
MAXP 1200 / 1055D / 1201D / 1601D / 2051D / 2055D / 2651D

Краткое содержание страницы № 2

TABLE OF CONTENTS Contents and introdction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page J Amplifier featuer descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - _. Page 2 Monoblock amplifier applications (MAXP J 200) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 3 Monoblock class D amplifier applications (MAXP J 055D/MAXP J 20 J D/MAXP J

Краткое содержание страницы № 3

AMPLIFIER FEATUER DESCRIPTIONS ~I055D/~IZOID/~160ID ~IZOO ~Z05ID/~Z65ID/~Z055D ~, o ~. I. Une Out RCA Jacks· The LINE OUT allows you to build multiple amplifier systems 5. Brigde Mode without having to use splitter cords to distribute the signal. Now it is simple a matter of 6. Variable Bass Boost Control· 0 - + 10dB bringing one set of RCAs into the first amplifier, then using the line out RCA jacks as the 7. Variable Subsonic Filter· 15Hz-35Hz feed to the next amplifier. 8. Low Pa

Краткое содержание страницы № 4

MAXPI ZOO MONO BLOCK AMPLIFIER APPLICATIONS Basic application Interconnect cable checklist: - Connect the line inputs to a Radio/CD RCA outputs or line output of the full range primary amplifier with good quality RCA cables. A "Y" adapter may be needed as shown in the diagram. - Use at least 16 gauge speaker wiring. These amplifiers have dual speaker terminals, simplifying the hookup of multiple speakers Crossover frequency control checklist: LOWPASS: 35Hz to 250Hz - - SUBSONIC: 15Hz

Краткое содержание страницы № 5

~PI055D/~PI201D/~PI601D/~P2051D/~P2651D ~P2055D MONO BLOCK CLASS D AMPLIFIER APPLICATIONS Basic application Interconnect cable checklist: - Connect the line inputs to a Radio/CD RCA outputs or line output of the full range primary amplifier with good quality RCA cables. _0 A "Y" ada per may be needed as shown in the diagram. 8UBWOOFER - Use at least 16 gauge speaker wiring. These amplifiers have dual nl!RBJU1I1! speaker terminals, simplifYing the hookup of multiple speakers ."""'" a

Краткое содержание страницы № 6

SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE General: At this point you are ready to get more specific on the settings for your amplifier. Subsonic: This setting acts as a low frequency cut off for your system bass reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o'clock position is a great starting point. EXAMPLE: If you adjust the Subsonic to 25Hz, the amplifier will not play frequencies below 25Hz but will play

Краткое содержание страницы № 7

Lanzar MAX PRO SERIES AMPLIFIER FEATURES MAXPI200 MAXPIOSSD MAXPI20lD MAXPI60lD MAXP20SID MAXP205SD MAXP26SID output Power Rating 4Ohmload 450xl Ix250W Ix500W Ix750W lxl000W lx625W lx1250W 2-Ohm load 900xl lx500W Ix 1 OOOW lx1500W lx2000W lx1250W lx2500W l-Ohm load 1800xl lxl000W lx2000W lx3000W lx4000W lx2500W lx5000W O.S-Ohm load NA lx2000W NA NA NA lx5000W NA Electrical Specifications Slow Un-Mute Tum-On (soft start) YES YES YES YES YES YES YES Dampening Factor >200 >300 >300 >30

Краткое содержание страницы № 8

TROUBLESHOOTING Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first. AMPLIFIER WILL NOT POWER UP. Check for good ground connection. Check that remote DC terminal has at least 13.Bv DC. Check that there is battery power on the +terminal. Check all fuses. Check that Protection lED is not lit. If it is lit shut off amplifier briefly and then repower it. HIGH HISS OR ENGINE NOISE (ALTERNATOR WHINE) IN SPE

Краткое содержание страницы № 9

()) *+*  !!!"#$%&'