Краткое содержание страницы № 1
®
FriendlyNET FM2017
SNMP/Web Managed Switch with Fiber Option
User’s Manual
Краткое содержание страницы № 2
2
Краткое содержание страницы № 3
Table Of Contents Chapter 1. Introduction 5 Features 5 Ethernet Switching Technology 6 Management Methods 6 Chapter 2. Hardware Installation 7 Package Contents 7 Front Panel 7 Rear Panel 8 Mounting Configurations 8 Powering on the Switch 8 Optional FX100 Modules 8 Chapter 3. Network Application 11 Small Workgroup 11 Segment Bridge 11 VLAN Application 11 Chapter 4. Network Configuration 1
Краткое содержание страницы № 4
4
Краткое содержание страницы № 5
Chapter 1. Introduction Thank you for purchasing an Asanté FriendlyNET FM2017 SNMP/Web managed switch. This switch is designed to build high-performance switched networks. It uses store-and-forward technology, providing low latency for high-speed networking, and is targeted at workgroup, department or backbone computing environments at small to medium enterprise businesses. The switch features full plug-and-play installation. LED indicators provide for easy monitoring of switch operati
Краткое содержание страницы № 6
Ethernet Switching Technology Ethernet switching technology has dramatically boosted the total bandwidth of a network, eliminating congestion problems inherent with Carrier Sense Multiple Access with Collision Detection (CSMA/CD) protocol, and has greatly reduced unnecessary transmissions. This revolutionized networking in the following ways: First, by allowing two-way, simultaneous transmissions over the same port (Full-duplex mode), which essentially doubled the network bandwidth; Sec
Краткое содержание страницы № 7
Chapter 2. Hardware Installation This chapter describes the front and rear panels of the FM2017, and explains how to install, mount and apply power to the switch. Package Contents The switch is shipped with the following items: • Switch • AC power cord • Four (4) Rubber feet • Rack mount Kit • RS-232 cable • User’s Manual (this document) Compare the contents of your switch’s package against the items listed above. If any of the items is missing or damaged, contact your deal
Краткое содержание страницы № 8
Rear Panel The rear panel contains the Network Management module and the 3-pronged power plug. The switch uses AC in the range of 100-240V AC, 50-60Hz. The Network Management module holds the Flash memory, and has two LEDs: CPU Fail: The CPU Fail LED is lit when the switch’s self test and initialization are in progress, after powering on or rebooting the switch CPU Activity: The CPU Activity LED is lit when the switch is displaying network management information Mounting Co
Краткое содержание страницы № 9
• FX100-MMC • FX100-SMC15 • FX100-SMC30 • FX100-SMC60 The FX100 modules are designed to extend the allowable distance between the switch and other network devices. The maximum distance that can be achieved with fiber cabling is 2 kilometers (multi-mode fiber) and up to 15, 30 or 60 kilometers (single-mode fiber). Front Panels The front panels of the FX100 modules consist of LED indicators, two thumbscrews, a DIP-switch for half and full-duplex mode (full-duplex is the default) a
Краткое содержание страницы № 10
10
Краткое содержание страницы № 11
Chapter 3. Network Application This section provides a few samples of network topology in which the switch can be used. In general, the switch is designed to be used as a segment switch. That is, with its large address table (8000 MAC address) and high performance, it is ideal for interconnecting networking segments. You can use the switch to connect PCs, workstations, and servers to each other by connecting these devices directly to the switch. The switch automatically learns nodes add
Краткое содержание страницы № 12
12
Краткое содержание страницы № 13
Chapter 4. Network Configuration This chapter explains how to configure console management via a direct connection to the console port of the switch. Console management involves the administration of the switch via a direct connection to the RS-232 console port. This port is a female DB-9 connector. From the main menu of the console program, the user has access to manage the functions of the switch. Connecting a Terminal or PC to the Console Port The console configuration (out-of-
Краткое содержание страницы № 14
---<>---------------------------[1.0(beta 2)]---- - [MAC=00:00:94:D1:1C:22] [IP=192.168.0.1] [mask=255.255.255.0] [broadcast=255.255.255.255] [gateway=0.0.0.0] ------------------------------------------------------------------------ - 1. boot-method = [flash] 2. ip-address = [192.168.0.1] 3. subnet mask = [255.255.255.0] 4. broadcast = [255.255.255.255] 5. gateway = [0.0.0.0] 6. traps=[0.0.0.0] [0.0.0.0] [0.0.0.0] [0.0.0.0] 7. get-communi
Краткое содержание страницы № 15
E. Http server = [on] F. Telnet/Http username = [root] G. Telnet/Http password = [enabled] H. reboot I. logout J. ping K. help L. loaddefault M. securedip = [0.0.0.0],[0.0.0.0],[0.0.0.0] >>>> Press H to reboot the switch after making your change. Press Enter twice, and the new IP address will now be displayed. By the similar methods, you can configure the Subnet Mask (Default subnet mask is 255.255.255.0
Краткое содержание страницы № 16
16
Краткое содержание страницы № 17
Chapter 5. Web-Based Management This section introduces the configuration and functions of the web-based management of switch. The FM2017 provides an embedded HTML website residing in the CPU module. It offers management features and allows users to manage the switch from anywhere on the network through a standard web browser. System Login 1. Launch your web browser. 2. Enter the IP address of the switch in the URL window (http://192.168.0.1). Then press Enter. 3. Then the follo
Краткое содержание страницы № 18
Inside the System page, the following information about the switch is listed: Network Setting • IP address: 192.168.0.1 • Subnet Mask: 255.255.255.0 • Broadcast: 255.255.255.255 • Default gateway: 0.0.0.0 The configuration above is only a reference setting. If you want to reset or change the numbers, you can click Agent Config to change or reset them. System Group • SysDescription: Lists the switch name and firmware version number • : Lists the time elapsed since pow
Краткое содержание страницы № 19
The data is automatically updated at regular intervals. Port Config Screen You can use the Port Config page to disable/enable each port. By default, all the ports are Enabled. To disable or enable a port: 1. Select the drop-down menu in the Status column. 2. Choose the status you want for each Ethernet and Fiber port. 3. Remember to click Apply button after finishing your new settings. Speed Config Screen In the Speed Config page, you can manually configure the speed
Краткое содержание страницы № 20
To set these parameters for a port: 1. Select the drop-down menu in Speed/Duplex column. 2. Select one of the following choices: Auto/flow control enabled, Auto/flow control disabled, 100Base- Tx/Full Duplex, 100Base-Tx/Half Duplex, 10Base-T/Full Duplex or 10Base-T/Half Duplex. 3. Click Apply. VLAN Screen A VLAN (Virtual LAN) is a group of switch ports designated by the switch as belonging to the same broadcast domain. This feature allows workgroups to be defined on the basis
