Краткое содержание страницы № 1
r
a
t
S
Operator’s Manual
TM M
2-Cycle Gasoline
Trimmer
Model TB65SS
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
P/N 769-01891 (6/05)
y
s
a
E
Краткое содержание страницы № 2
INTRODUCTION THANK YOU TABLE OF CONTENTS Thank you for buying this quality product. This modern Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2 outdoor power tool will provide many hours of useful service. You will find it to be a great labor-saving device. Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3 This operator’s manual provides you with easy-to- understand operating instructions. Read the whole Know Your Unit . . . . . . . . . . . . . . . . . .
Краткое содержание страницы № 3
RULES FOR SAFE OPERATION The purpose of safety symbols is to attract your SYMBOL MEANING attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by Failure to obey a DANGER: themselves eliminate any danger. The instructions or safety warning will warnings they give are not substitutes for proper result in serious injury to yourself or to accident prevention measures. others. Always follow the safety p
Краткое содержание страницы № 4
RULES FOR SAFE OPERATION • Always stop the engine and allow it to cool before filling • Keep hands, face, and feet at a distance from all the fuel tank. Never remove the cap of the fuel tank, or moving parts. Do not touch or try to stop the cutting add fuel, when the engine is hot. Never operate the unit attachment when it is rotating. without the fuel cap securely in place. Loosen the fuel • Do not touch the engine or muffler. These parts get tank cap slowly to relieve any pressure in the tank.
Краткое содержание страницы № 5
RULES FOR SAFE OPERATION SAFETY AND INTERNATIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING SYMBOL MEANING • THROWN OBJECTS AND • SAFETY ALERT SYMBOL ROTATING CUTTER CAN CAUSE Indicates danger, warning, or SEVERE INJURY caution. May be used in conjunction with other symbols or pictographs. WARN
Краткое содержание страницы № 6
RULES FOR SAFE OPERATION KNOW YOUR UNIT Blue EZ-Start™ Lever APPLICATIONS As a trimmer: Muffler Guard • Cutting grass and light weeds. • Edging Fuel Cap • Decorative trimming around trees, fences, etc. Muffler Starter Rope Grip Spark Plug Shaft Grip On/Off Stop Control Throttle Control D-Handle Blue EZ-Start™ Air Filter/Muffler Lever Cover Shaft Housing Cutting Attachment Shield Line Cutting Blade Engine Stand Muffler Cutting Attachment Spark Plug Primer Bulb 6
Краткое содержание страницы № 7
ASSEMBLY INSTRUCTIONS INSTALL AND ADJUST THE D-HANDLE INSTALLING THE CUTTING ATTACHMENT SHIELD 1. Push the D-handle down onto the shaft housing so that the handle slants towards the shaft grip (Fig. 1). Use the following instructions if the cutting attachment The squared bolt hole in the handle is to the right. shield on your unit is not installed. 2. Insert the shoulder bolt into the squared hole in the To prevent serious handle and push through. On the left side of the WARNING: personal injury
Краткое содержание страницы № 8
OIL AND FUEL INFORMATION Thoroughly mix the proper ratio of 2-cycle engine oil OIL AND FUEL MIXING INSTRUCTIONS with unleaded gasoline in a separate fuel can. Use a 40:1 Old and/or improperly mixed fuel are the main reasons fuel/oil ratio. Do not mix them directly in the engine fuel for the unit not running properly. Be sure to use fresh, tank. See the table below for specific gas and oil mixing clean unleaded fuel. Follow the instructions carefully for ratios. the proper fuel/oil mixture. NOTE:
Краткое содержание страницы № 9
STARTING/STOPPING INSTRUCTIONS Stop/Off (O) Operate this unit only in a WARNING: well- ventilated outdoor Start/On ( I ) area. Carbon monoxide exhaust fumes can be lethal in a confined area. Avoid accidental starting. WARNING: Make sure you are in the starting position when pulling the starter rope (Fig. 8). To avoid serious injury, the operator and unit must be in a stable position while starting. Throttle Control Make sure that any Add-On item is installed correctly and secure before starting
Краткое содержание страницы № 10
OPERATING INSTRUCTIONS NOTE: Do not rest the Bump Head™ on the ground HOLDING THE TRIMMER while the unit is running. Always wear eye, Some line breakage will occur from: WARNING: hearing, foot and • Entanglement with foreign matter body protection to reduce the risk of injury when operating this unit. • Normal line fatigue Before operating the unit, stand in the operating position • Attempting to cut thick, stalky weeds (Fig. 9). Check for the following: • Forcing the line into objects such as w
Краткое содержание страницы № 11
MAINTENANCE AND REPAIR INSTRUCTIONS MAINTENANCE SCHEDULE NOTE: Maintenance, replacement, or repair of the emission control devices and system may be Perform these required maintenance procedures at the performed by any non-road engine repair frequency stated in the table. These procedures should establishment, individual or authorized service also be a part of any seasonal tune-up. dealer. NOTE: Some maintenance procedures may require In order to assure peak performance of your engine, special t
Краткое содержание страницы № 12
MAINTENANCE AND REPAIR INSTRUCTIONS For Use with Single For Use with SplitLine™ 9. Insert the end of the line into the open hole in the Line ONLY or Single Line inner reel and pull the line tight to make the loop as small as possible (Fig. 18). Slotted Holes 10. Before winding, split the line back about 6 inches. 11. Wind the line in tight even layers in the direction indicated on the inner reel. NOTE: Failure to wind the line in the direction indicated will cause the cutting attachment to opera
Краткое содержание страницы № 13
MAINTENANCE AND REPAIR INSTRUCTIONS Cleaning the Air Filter INSTALLING A PREWOUND REEL Clean and re-oil the air filter every 10 hours of operation. 1. Hold the outer spool with one hand and unscrew the It is an important item to maintain. Failure to maintain bump knob counterclockwise (Fig. 12). Inspect the bolt your air filter properly can result in poor performance or inside the bump knob to make sure it moves freely. can cause permanent damage to your engine. Replace the bump knob if damaged.
Краткое содержание страницы № 14
MAINTENANCE AND REPAIR INSTRUCTIONS SPARK ARRESTOR MAINTENANCE If the exhaust WARNING: deflector assembly is NOTE: The exhaust can only flow in one direction: AWAY not tightened securely, it could fall off causing from the engine. Pay close attention when damage to the unit and possible serious disassembling the muffler so you can put it back personal injury. together correctly. Failure to do so will damage the unit and may cause serious personal injury. 1. Remove air filter/muffler cover. Refer
Краткое содержание страницы № 15
MAINTENANCE AND REPAIR INSTRUCTIONS CARBURETOR ADJUSTMENT The idle speed of the engine is adjustable through the air filter/muffler cover (Fig. 27). NOTE: Careless adjustments can seriously damage your unit. An authorized service dealer should make carburetor adjustments. Check Fuel Mixture Idle Speed Screw Old and/or improperly mixed fuel is usually the reason for improper unit performance. Drain and refill the tank with fresh, properly-mixed fuel prior to making any adjustments. Refer to Oil a
Краткое содержание страницы № 16
MAINTENANCE AND REPAIR INSTRUCTIONS REPLACING THE SPARK PLUG STORAGE Use a Champion RDJ7Y spark plug (or equivalent). • Never store the unit with fuel in the tank where fumes The correct air gap is 0.020 inch (0.5 mm). Remove the may reach an open flame or spark. plug after every 25 hours of operation and check its • Allow the engine to cool before storing. condition. • Store the unit locked up to prevent unauthorized use or 1. Stop the engine and allow it to cool. Grasp the plug damage. wire
Краткое содержание страницы № 17
TROUBLESHOOTING ENGINE WILL NOT START CAUSE ACTION Empty fuel tank Fill fuel tank with properly mixed fuel Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times Engine is flooded Squeeze the trigger and pull the starter rope Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture Fouled spark plug Replace or clean the spark plug Plugged spark arrestor Clean or replace spark arrestor EZ-Start lever wasn’t flipped/set Move lever to the starting position The o
Краткое содержание страницы № 18
SPECIFICATIONS ENGINE* Engine Type.......................................................................................................................................... Air-Cooled, 2-Cycle Stroke.................................................................................................................................................... 1.25 in. (31.75 mm) Displacement........................................................................................................................
Краткое содержание страницы № 19
California / EPA Emission Control Warranty Statement Your Warranty Rights and Obligations The California Air Resources Board, the Environmental Protection Agency and MTD LLC (MTD) are pleased to explain the emission control system warranty on your 2000 and later small off-road engine. New small off-road engines must be designed, built and equipped to meet stringent anti-smog standards. MTD must warrant the emission control system on your small off-road engine for the periods of time listed belo
Краткое содержание страницы № 20
MANUFACTURER’S LIMITED WARRANTY FOR: No implied warranty, including any implied warranty of The limited warranty set forth below is given by Troy-Bilt merchantability or fitness for a particular purpose, LLC with respect to new merchandise purchased and used applies after the applicable period of express written in the United States, its possessions and territories. warranty above as to the parts as identified. No other Troy-Bilt LLC warrants this product against defects in express warranty or g
