Краткое содержание страницы № 1
INSTALLATION INSTRUCTIONS
Medium Flat Panel
Pivot/Pitch Wall Mount
Model JWP-V
The JWP Pivot/Pitch wall mount is designed for
mounting a medium sized flat panel display. The mount
can be tilted up and down to 15° of center as well as
pivot left and right.
®
The JWP is shipped with the VESA 100mm/100mm
Centris™ interface which is compatible with most
medium flat panels.
To accommodate other mounting patterns in displays,
the JWP comes with a VESA Plate that accommodates
other VESA mounting pa
Краткое содержание страницы № 2
Installation Instructions JWP-V IMPORTANT WARNINGS and CAUTIONS! WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING Improper installation can result in serious personal injury! Make sure that the structural members can support a redundant weight factor five times the total weight of the eq
Краткое содержание страницы № 3
Installation Instructions JWP-V CONTENTS TOOLS REQUIRED FOR INSTALLATION DIMENSIONAL DRAWING ..................................... 2 TOOLS REQUIRED FOR INSTALLATION............ 3 Electric drill and bit set INSPECT UNIT BEFORE INSTALLING................. 3 Hex wrench set SPECIFICATIONS ................................................... 3 Phillips screwdriver INTRODUCTION...................................................... 4 Level PARTS.......................................................
Краткое содержание страницы № 4
Installation Instructions JWP-V 200mm x 200mm INTRODUCTION 200mm x 100mm There are 3 main steps in the JWP-V installation process. These steps are: Selecting an appropriate mounting configuration. Connect display cables Making required adjustments Before starting the installation process, determine the correct mounting hole configuration for your display by reviewing the information located within Table 2 at right. NOTE: If the displays mounting hole configuration does not match those identi
Краткое содержание страницы № 5
Installation Instructions JWP-V PARTS Centris Bracket (See notes) 10 Set Screw (see notes) BAG A BAG B BAG C BAG D BAG E Figure 2. JWP-V Components 5
Краткое содержание страницы № 6
Installation Instructions JWP-V PARTS (Continued) Table 2 shows the individual part and parts bags shipped with JWP parts. Table 2. JWP Parts List Item Bag Description Qty Notes 10 — MSP-MA MOUNT (with Centris bracket) 1 20 — Interface Bracket 1 30 — Wall Bracket 1 Use with 40 40 — Lag Screws, 3/8” x 3” 2 Use with 30 No spacers needed for 100mm x 100mm flush 50 Phillips Head Cap Screw, M4 X 12mm 4 mounted Centris bracket. For 200mm x 100mm 60 Phillips Flat Head Machine Screw, M4 X 16mm 6 and 300
Краткое содержание страницы № 7
Installation Instructions JWP-V SECURE WALL BRACKET WARNING: It is the responsibility of the installer to verify that the surface to which the mount is anchored will safely support the combined load of all attached components and equipment. Install wall bracket as follows: 1. Determine exact mounting location prior to Pilot Holes installation, considering unit’s swing arm and extension radius. 2. Using wall bracket (30) as a template, mark two pilot holes. (See Figure 1) 30 3. Drill two ¼” pil
Краткое содержание страницы № 8
Installation Instructions JWP-V Recess Mount Installation 60 To recess mount Centris Bracket: 1. Lay display down on a flat surface. CAUTION: Make sure surface is clean and free of dirt and debris before laying display down. 100 2. Select four screws M4 x 20mm screws (60) and four Display spacers (100) from parts bag. 3. Place four spacers (100) over mounting holes on back of display (see Figure 3). 4. Align mounting holes on Centris bracket with spacers installed on display. 5. Install four M4
Краткое содержание страницы № 9
Installation Instructions JWP-V Interface Bracket Installation SCREW* DISPLAY The following sections describe how to install the (BAG A OR B) interface bracket (20) for a specific hole-pattern on MOUNTING your display. HOLE This procedure provides a general guideline to follow when installing the interface bracket after selecting the mounting-hole pattern procedure that matches your display. For example: To install the interface bracket using the 200mm x 100mm mounting-hole pattern, use the proc
Краткое содержание страницы № 10
Installation Instructions JWP-V 200mm x 100mm Pattern For the 200mm x 100mm hole pattern, do the following: 1. Select six flat head M4 screws (60) from Bag A and six spacers (130) from Bag C. 2. Attach the interface bracket (20) using the hole- pattern on the back of your display as shown in Figure 5. 3. Tighten each screw. To prevent equipment damage, do not over-tighten the screws. Figure 5. Display with 200mm x 100mm Hole Pattern 300mm x 100mm Pattern For the 300mm x 100mm hole pattern, do th
Краткое содержание страницы № 11
Installation Instructions JWP-V 300mm x 200mm Pattern For the 300mm x 200mm hole pattern, do the following: 1. Select eight Phillips head M6 screws (110) from Bag B and eight spacers (120) from Bag C. 2. Attach the interface bracket (20) using the hole- pattern on the back of your display as shown in Figure 7. 3. Tighten each screw. To prevent equipment damage, do not over-tighten the screws. Figure 7. Display with 300mm x 200mm Hole Pattern 400mm x 200mm Pattern For the 400mm x 200mm hole patte
Краткое содержание страницы № 12
Installation Instructions JWP-V 200mm x 200mm Pattern For the 200mm x 200mm hole pattern, do the following: 1. Select the applicable screws as follows: a. If using square hole on interface bracket (20), select four Phillips head M4 screws from Bag A. OR b. If using round hole on interface bracket (20), select four Phillips head M6 screws from Bag B. c. Select spacers (120) or (130) from Bag C. 2. Attach the interface bracket (20) using the hole- pattern on the back of your display as shown in Fi
Краткое содержание страницы № 13
Installation Instructions JWP-V Attach Display to Mount (Centris Bracket) Display After attaching the interface bracket onto the display, the next step is to attach the display to the mount (Centris bracket). Centris To attach the display to the Centris bracket, do the Bracket following: 1. Select four Phillips head M4 x 8mm screws (80) from Bag A. 2. Start two M4 x 8mm screws (80, Bag A) into top mounting holes on display (see Figure 11) 80 3. Align mounting holes on Centris bracket with screws
Краткое содержание страницы № 14
Installation Instructions JWP-V CABLE MANAGEMENT Lateral Tension Adjustment Bolt WARNING: Make sure your cables do not run through a pinch points. Do not put your fingers between movable parts. For cable management (not shown), connect and secure power/audio/video cables, making sure to leave sufficient slack to allow for movement of the display. ADJUSTMENTS Lateral Tension Adjustment To adjust Lateral Tension: 1. Move arms laterally to check for desired tension. 2. Using a 3/16” hex wrench slig
