Краткое содержание страницы № 1
Installation Guide
MM850
8.5" LCD OVERHEAD MONITOR
ON OFF AUTO
P
P
POWER UP
MENU/
DOWN
ENTER
Installation Guide
1
Краткое содержание страницы № 2
Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied. An LCD p
Краткое содержание страницы № 3
Installation Guide MATERIALS INCLUDED IN THIS PACKAGE: 1) MM850 Video Monitor (P/N 136-3869) – 1pc 2) Trim Ring (P/N 102C4007) – 1pc 3) Remote Control (P/N : 136B3650) – 1pc 4) Hardware Package:- ♦ #4 x 5/16” Screws – 7 pcs ♦ #8 x 5/8” Self Drilling Screws – 4 pcs ♦ #8 Washers – 4 pcs 5) 2 Pin Power Wire Harness with choke (P/N 112B3143) – 1 pc 6) Dome light Harness (P/N 112B3110) – 1 pc 7) Accessory Harness (P/N 8010730) – 1pc 8) A/V Adapter Cable (P/N 112B3227) – 1pc 1. 2. 3
Краткое содержание страницы № 4
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Tuner, RF Modulator/external amp, remote headphones, DVD, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting wire h
Краткое содержание страницы № 5
Installation Guide VEHICLE PREPARATION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off). Also locate a good ground wire. Generally, these wires can be found at the ignition switch or fuse-box. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories. 3) Generally, the best location for the video monitor is where the v
Краткое содержание страницы № 6
TRIM RING INSTALLATION: This page only covers special installation considerations for the trim ring installation. If the video monitor is to be installed in a vehicle with the trim ring, it may need to be trimmed to fit the contour of the vehicle headliner. 1) In this installation, the video monitor is mounted directly to the overhead cross-member in the roof using the mounting screw bosses. These screw bosses should contact the cross-member di- rectly (i.e.: no gap between the screw boss and t
Краткое содержание страницы № 7
Installation Guide MOUNTING THE TRIM RING Roof Roof Support Headliner 5"x9"x3/4" Plywood Block (4) #8x1" self drilling screws Trim Ring Video Unit (4) #8 flat washers (4) #8x3/4" self tapping screws 7
Краткое содержание страницы № 8
MM850 Dome Light item #6 Video Output 1 Audio Output forFM Mod. Accessory Red: +12VDC Harness item #7 Accessory Ckt. (Install 5A Red RCA (Audio Right) Inline Fuse) Power Harness White RCA (Audio Left) item #5 Yellow RCA (Video) Black: Ground Power Connector 4 Pin “Y” Adapter IR LED: for use with Clean the IR Receiver Window on the front of the VCP. Non-Stereo Remove Adhesive Backing and Apply IR LED to IR Installations Window on the Face of the VCP. ANT.IN FUSE RF OUT DC IN OUT 1) Insert t
Краткое содержание страницы № 9
Installation Guide CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply volt- age to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed a
Краткое содержание страницы № 10
Negative Switched Dome lighting Red / black - Lamp on To 3 pin Black / red - Lamp common connector Violet / brown - Lamp Auto To constant Factory Dome light circuit To constant Factory Door ajar switch or Body Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor -Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor. Verify ground connection with continuity test from known good ground to black wire at 2 pin Power Harness Power but no video or -Verify that the correct s
Краткое содержание страницы № 11
Installation Guide 11
Краткое содержание страницы № 12
© Copyright 2004 AEC 150 Marcus Blvd. Hauppauge, NY 11788 128-7265
