Руководство по эксплуатации Metra Electronics

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-8902
APPLICATIONS
SUBARU
Impreza2008-2011
Forester2009-11
99-8902
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
KIT COMPONENTS
•A) Radio Housing • B) ISO Brackets • C) Trim Plate
C
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
A Wire harness:
• 70-7552 Nissan harness 2007-up
• 70-8901 Subaru harness 1990-up
Antenna adapter:
• 40-SB10 Subaru antenna adapter 2005-up
TOOLS REQUIRED:
Small Flat Blade Screw

Краткое содержание страницы № 2

99-8902 TABLE OF CONTENTS Dash Disassembly - SUBARU Impreza 2008-2011. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - SUBARU Forester 2009-2011. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 - ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Final Assembly . . . .

Краткое содержание страницы № 3

99-8902 DASH DISASSEMBLY SUBARU IMPREZA 2008-11/FORESTER 2009-11 1 A Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the trim panel surrounding the factory radio includ- ing the a/c vents. (Figure A) 3 Remove (4) Phillips screws securing the radio. Unplug and remove the radio. (Figure B) Continue to kit assembly. B 1 2 3 4 5 TEXT CD/AUX RPT FM/AM SAT SCAN PTY/CAT MENU VOLUME TUNE/TRACK/CH 1

Краткое содержание страницы № 4

99-8902 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) Continue to final assembly. B 2

Краткое содержание страницы № 5

99-8902 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the Trim plate onto the front of the Radio Housing. (Figure B) Continue to final assembly. B 3

Краткое содержание страницы № 6

99-8902 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse

Краткое содержание страницы № 7

99-8902 NOTES 5

Краткое содержание страницы № 8

99-8902 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 11/18/10 © COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION INST99-8902