Краткое содержание страницы № 1
C
N
E
R
G
T
I
Multisided Top/Rear Vent
Convertible Direct Vent
Fireplaces: 360DVS2
360DVS3
360DVSL
360DVSR
INSTALLER/CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND USING
APPLIANCE
IMPORTANT: Read all instructions
and warnings carefully before
starting installation. Failure to follow
these instructions may result in a
possible fire hazard, and will void the
warranty.
WARNING: If the information in this
manual is not followed exactly, a fire or
explosion ma
Краткое содержание страницы № 2
360DVS Series Direct Vent Fireplaces Installation & Operating Instructions This gas appliance should be installed by a qualified installer in accordance with local building codes and current CSA-B149.1 This appliance may be installed in an aftermarket, per- manently located, manufactured home, or mobile home Installation Codes for Gas Burning Appliances and Equipment. where not prohibited by local codes. If the unit is being installed in a mobile home, the installation should comply with the
Краткое содержание страницы № 3
360 DVS Series Direct Vent Fireplaces Fireplace Dimensions - 360DVS2 J J I Rear Vent Configuration K H H K B E A E D A G Electrical Electrical Access Access Gas Line Gas Line J J Access Access J J F K C K J 6326 J 360DVS2 Top Vent Configuration rear vent K specs H H K B G C I E A E D A Electrical Electrical Access Access Gas Line Gas Line J J Access Access J F J K K Fig. 2a Fireplace specifications—360DVS2 6326 360DVS2 Appliance Dimensions top vent specs Ref. Rear Ve
Краткое содержание страницы № 4
360DVS Series Direct Vent Fireplaces Fireplace Dimensions - 360DVS3 / 306DVSL / 360DVSR J K I Rear Vent Configuration H H K B ROD A E D G Electrical Access Gas Line J Access J F C K C B J K I 6326 Top Vent Configuration 360DVS3 rear vent H specs H K B G A E D Electrical Access J Gas Line Access J F C K B 6326 Fig. 2b Fireplace specifications—360DVS3/ 360DDVSL/ 360DVSR 360DVS3 top vent specs Appliance Dimensions Ref. Rear Vent Configuration Top Vent Configuration A 38 ¹⁄₈” (9
Краткое содержание страницы № 5
360 DVS Series Direct Vent Fireplaces Framing Dimensions - 360DVS2 ROD Rear Vent Configuration ROH CFM121 ROW ROD Top Vent CFM121 Configuration 360DVS2 REAR VENT CONFIGURATION 8/10/00 ROH ROW CFM122 Fig. 3a Fireplace framing dimensions—360DVS2 CFM122 360DVS2 - TOP VENT CONFIGURATION Framing Dimensions 8/10/00 Ref. Rear Vent Configuration Top Vent Configuration ROD 24” (610 mm) minus two times finishing material thickness to be even with face of unit. ROH 38 ⁵⁄₈” (981 mm) Not to be framed u
Краткое содержание страницы № 6
360DVS Series Direct Vent Fireplaces Framing Dimensions - 360DVS3 / 360DVSL / 360DVSR Rear Vent Confiration ROD ROW ROD ROD ROH ROH ROH 360DVSL 360DVS3 360DVSR CFM123 360DVS/3/L/R Top Vent Configuration CFM123_360DVS3_dims_RV2 REAR VENT CONFIGURATION 8/10/00 rev. 8-23-02 rjs ROD ROD ROD ROW ROH ROH ROH 360DVSL 360DVS/3/L/R 360DVS3 360DVSR CFM124 Fig. 3b Fireplace framing dimensions—360DVS3/ 360DVSL/ 360DVSR CFM124_360DVS3_TV2 TOP VENT CONFIGURATION 8/10/00 Framing Dimensions rev. 8-23-02
Краткое содержание страницы № 7
360 DVS Series Direct Vent Fireplaces Clearance to Combustibles Top View Appliance Top .........................................0” (0 mm) to standoff Bottom ..................................................... 0” (0 mm) Vent End ....................... 1/2” (13 mm) to rear panel Nonvent End (DVS2) .............................. 0” (0 mm) Venting J I H Concentric sections of DV Vent: G Mantel Leg F Top, bottom & sides .............................. 1” (25 mm) Nonconcentric sections of
Краткое содержание страницы № 8
360DVS Series Direct Vent Fireplaces Gas Inlet & Manifold Pressures Framing & Finishing Natural LP (Propane) 1. Choose the unit location. Inlet Minimum 4.5” w.c. 11.0” w.c. 2. Place the unit into position and secure it to the floor Inlet Maximum 14.0” w.c. 14.0” w.c. with 1 ¹⁄₂” (38mm) screws or nails. Holes to secure Manifold Pressure 3.5” w.c. 10.0” w.c. the unit to the floor are located behind the access door grille on the left and right sides of the unit. Input ratings are shown in BTU
Краткое содержание страницы № 9
360 DVS Series Direct Vent Fireplaces The gas control is equipped with a captured-screw type pressure test point, therefore it is not necessary to pro- vide a 1/8” test point upstream of the control. When using copper or flex connector, use only ap- proved fittings. Always provide a union when using Electrical Inlet Hole black iron pipe so that the gas line can be easily discon- nected for burner or fan servicing. Refer to the gas specification for pressure details and ratings. Isolate or disc
Краткое содержание страницы № 10
360DVS Series Direct Vent Fireplaces Remove These Screws Remove These Screws FP1430 Fig. 8 Alternate switch location. Optional Top Vent Application Outer Collar Adapter This appliance is shipped as a rear vent unit. If the FP1431 installation layout requires the unit to be a top vent con- Fig. 9 Remove screws from outer collar adapter. figuration, the appliance can be converted by following FP1431 the steps below. Insulation Pad top vent (Must be removed) When removing and refitting the plat
Краткое содержание страницы № 11
LO 360 DVS Series Direct Vent Fireplaces Electronic Gas Control Valve This appliance may be fitted with a Honeywell ignition module. Installation of the remote ON/OFF starter switch on electronic ignition units (Fig. 12): 1. Thread the wiring through the holes on the side PILOT panels of the appliance. Take care not to cut the wire or insulation on metal edges. Route the wire to a HONEYWELL IGNITION MODULE conveniently located receptacle box. 24V MV MV/VP PV GR
Краткое содержание страницы № 12
V V Operabl e 360DVS Series Direct Vent Fireplaces General Venting Information - Termination Location INSIDE CORNER DETAIL G V N H N A D E B C B Fixed Fixed L V B V Closed Closed V Fixed Operable G Closed F V V B M V G B X B J I K X V V A A AREA WHERE TERMINAL IS NOT PERMITTED V VENT TERMINATION X AIR SUPPLY INLET CFM145a 1 2 Canadian Installations US Installations CFM145a A = Clearance above grade, veranda, porch, 12” (30cm) DV Termin Location 12” (30cm) 5/01/01 Rev. 12/05/01 deck,
Краткое содержание страницы № 13
360 DVS Series Direct Vent Fireplaces Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. Inside Corner Recessed Location Outside Corner D B = C C Combustible A = 6"(152mm) E Combustible A 6"(152mm) Noncombustible V V 2"(50mm) Noncombustible 2"(50mm) V B Balcony - Balcony - with no side wall with perpendicular side wall C = Maximum depth of 48" (1219mm) for recessed H G location. V V D = Minimum width
Краткое содержание страницы № 14
Vertical dimension from floor of the unit to center of the horizontal vent pipe 360DVS Series Direct Vent Fireplaces How to Use the Vent Graph Rear Wall Application The vent chart should be read in conjunction with the When installed as a rear vent unit this appliance may be following vent installation instructions to determine the vented directly to a termination located on the rear wall relationship of the vertical and horizontal dimensions of behind the appliance. the vent system. • Spec
Краткое содержание страницы № 15
360 DVS Series Direct Vent Fireplaces STEP 5 Vent Opening for Combustible Wall Guide vent through the vent hole as you place the appli- 9 ³⁄₈” (240mm) ance in its installed position. Guide the 4” (102 mm) and 7” (178 mm) collars of the vent termina- tion into the outer ends of the venting. 10 ³⁄₈” Do not force the termination. If the vent pipes do not (265mm) align with the termination, remove and realign the vent- ing at the appliance flue collars. Attach the termination to the wall as outl
Краткое содержание страницы № 16
360DVS Series Direct Vent Fireplaces Horizontal plane means no vertical rise exists on this • The maximum number of 45° elbows permitted per portion of the vent assembly. side wall installation is two (2). These elbows can be installed in either the vertical or horizontal run. • The maximum number of 90˚ elbows per side wall • For each 45° elbow installed in the horizontal run, installation is three (3). the length of the horizontal run MUST be reduced by • If a 90˚ elbow is fitted direct
Краткое содержание страницы № 17
360 DVS Series Direct Vent Fireplaces STEP 4 Vent Opening for Combustible Wall Apply a bead of silicone to the inner and outer flue 9 ³⁄₈” (240mm) collars of the fireplace and using appropriate length of pipe section(s) attach to fireplace with three (3) screws. Follow with the installation of the inner and outer elbow, again secure joints as described in “Connecting Vent 9 ³⁄₈” (240mm) Pipes” section. STEP 5 Measure the horizontal length requirement including a Framing Detail 2” (51 mm) over
Краткое содержание страницы № 18
360DVS Series Direct Vent Fireplaces 2” (51 mm). Secure termination to the wall with screws Zero Clearance provided, and caulk around the wall plate to weather- Sleeve (if required) 7TDVSNORK proof. (Snorkel) Firestop One alternative to screwing the termination directly to Screws Min. 4” (102mm) 7” Pipe the wallis the use of expanding plugs or an approved Clearance (Ground) exterior construction adhesive. Or, you may attach the termination with screws through Window Well the inner body i
Краткое содержание страницы № 19
360 DVS Series Direct Vent Fireplaces Vertical Through-the-Roof Application This Gas Fireplace has been approved for: 1 + 2 + 3 + 4 = 270° • Vertical installations up to 40’ (12 m) in height. Up 1 to a 10’ (3 m) horizontal vent run can be installed 1 within the vent system using a maximum of two 90° 2 2 elbows. (Fig. 30) 3 3 4 4 Max. Height 40’ (12.2m) Min. Height 8’ (2.4m) Max. 10’ (3m) FP1444 Fig. 31 Maximum elbow usage. Support Straps Every 36” (914mm) Min. 2' (610 mm) Max. 10’ (3m) Ma
Краткое содержание страницы № 20
360DVS Series Direct Vent Fireplaces If there is a room above ceiling level, a Vertical Through-the-Roof Installation firestop spacer must be installed on both 1. Locate your fireplace. the bottom and the top sides of the ceiling joists. (Fig. 35) If an attic is above ceiling 2. Plumb to center of the (4”) flue collar from ceiling level, a 7DVAIS (Attic Insulation Shield) above and mark position. must be installed. 3. Cut an opening equal to 9 ³⁄₈” x 9 ³⁄₈” (240 x 240mm). NOTE: The enlarged e
