Краткое содержание страницы № 1
150 WATT PORTABLE
CLAMP LIGHT
35149
ASSEMBLY & OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web Site at www.harborfreight.com
© ®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the express
written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
Краткое содержание страницы № 2
THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below: Model______________ Serial No.____________ Purchase Date_______________ SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly. Technical Specifications Power: 120 VAC, 60 Hz Amps: 1 E197534 Watts: 150 Bulb Type: Quartz Halogen, 3 inch (78mm) len
Краткое содержание страницы № 3
ELECTRICAL SAFETY 4. Grounded lights must be plugged into an outlet properly installed and grounded in ac- cordance with all codes and ordinances. Never remove the grounding prong or mod- ify the plug in any way. Do not use any adapter plugs. Check with a qualified elec- trician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 5. Do
Краткое содержание страницы № 4
15. Use safety equipment. Always wear eye protection. TOOL USE AND CARE 16. Do not force the Clamp Light. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 17. Do not use the light if the On/Off Switch does not turn it on or off. 18. Disconnect the Power Cord Plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduc
Краткое содержание страницы № 5
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS Note: The Clamp Light has a Three Prong Plug. 1. Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the Stapler should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See Figure A.) 2. The grounding prong in the plug is
Краткое содержание страницы № 6
EXTENSION CORDS 1. Grounded appliances require a three wire extension cord. Double Insulated products can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Figure C, next page.) 3. The smaller the gauge number of the wire, the greater the capacity of
Краткое содержание страницы № 7
SPECIFIC SAFETY RULES 1. WARNING! Do not mount the Clamp Light on or in any residential structure. Mounting in such a location creates a fire hazard that can result in property damage, severe personal injury, and/or death. 2. ALWAYS point the Light away from the wall, whether the unit is in use or not. If the light is accidentally pointed at the wall while it is on or while it is still hot when turned off, a fire may result. 3. Keep all flammable materials and wall hangings at
Краткое содержание страницы № 8
SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current V ~ Amperes A n No Load Revolutions o xxxx/min. Per Minute (RPM) WARNING! The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpac
Краткое содержание страницы № 9
2. The Spring Clamp (1) can be mounted to the Bracket (7) at any of the three holes located at the end of the Spring Clamp (1). Decide on the angle to attach the Spring Clamp (1) to the Bracket (7) - see Figure 2. Thread in Phillips Head Bolt (5) through the Bracket (7) and into the Spring Clamp (1). If the Phillips Head Bolt (5) does not thread in tightly, you may have to add several washers (not included) to obtain a tight fit. 3. The Clamp Light has a Handle (2), which should be
Краткое содержание страницы № 10
Operation 1. To turn on the Clamp Light, plug the Power Cord into the nearest 120 volt, grounded, electrical outlet. Then, press the On/Off Switch located on the back of the Clamp Light. WARNING! Always point the light away from the wall, whether the unit is in use or not. If the unit is accidentally pointed at the wall while turned on or still hot after turned off, a fire may result. 2. To turn off the Halogen Light, press the On/Off Switch located on the back of the Light. Then, unp
Краткое содержание страницы № 11
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of maintenance. We shall in
