Краткое содержание страницы № 1
M M5726 5726
1. Basketball
2. Football
3. Soccer
4. Baseball
5. Hockey
Please keep this instruction sheet for future reference, Please keep this instruction sheet for future reference,
a as it contains important information. s it contains important information.
Adult assembly is required. Adult assembly is required.
T To ool needed for assembly: Phillips screwdriver (not included). ol needed for assembly: Phillips screwdriver (not included).
W Water or sand is needed to fi ater or sand is needed
Краткое содержание страницы № 2
ASSEMBLED P ASSEMBLED PA AR RT TS S Net Tube Backboard Base Tube 2 Side Tubes Rim 2 Post Covers 2 Base Covers 2 Upper Posts Net 2 Lower Posts 2 Plugs Label Sheet 3 #8 x /4” Screw – 36 1 #10 x 1 /2” Screw – 2 BOTH SHOWN ACTUAL SIZE 2 Bases Note: Tighten all screws with a Phillips screwdriver. Do not over-tighten the screws. 2 2
Краткое содержание страницы № 3
A ASSEMBL SSEMBLY Y CAUTION 2 This product contains small parts in its unassembled state. Adult assembly is required. Printed Side Up Posts 1 Sleeve Base Tube 2 • Place the net, printed side up, on a flat surface. • Slide the base tube through the sleeve on the bottom of the net. 1 3 Bases • Place the bases on a flat surface. • Note the numbers on the bases and on the posts. • Insert and “snap” the post labeled 1 into the base labeled 1 . 2 2 • Insert and “snap” the post labeled into the
Краткое содержание страницы № 4
A ASSEMBL SSEMBLY Y Post Grooves 4 6 Sleeve Side Tube Sleeve Side Tube • Slide a side tube, straight end first, through the sleeve on each • Fit the upper end of the side tubes into the groove in each post. side of the net. 7 5 Side Tubes 2 1 Base Covers • Note the numbers on the base covers. • Fit the base cover labeled 1 onto the base assembly labeled 1 . Hint: Make sure the net is not under the base cover. • Lift the side tubes up and set the ends in the notch in each 3 • Insert four #8 x /4”
Краткое содержание страницы № 5
ASSEMBL ASSEMBLY Y Side Net Tube Tube 8 10 Post Cover Post Cover • Fit a post cover over the end of a side tube and onto a post. 3 • Insert five #8 x /4” screws into the post cover and tighten. • Repeat this procedure to attach the other post cover. • Line up the holes in the ends of the net tube with the hole in each side tube. 1 • Insert a #10 x 1 /2” screw into each side tube and tighten. 9 11 Net Tube P Plastic T lastic Ta ab b • Fit the net tube through the sleeve in the center of the ne
Краткое содержание страницы № 6
ASSEMBL ASSEMBLY Y Straps 13 12 Plastic Tabs Front View • Lift the top of the net. • Insert the ends of the straps at the top of the net into the slot near the top of each post. • Feed the end of the strap up through the center slot in the buckle. Then feed the end of the strap down through the slot at the end of the buckle. Note: Do not completely tighten the straps at this time. Back View • From the front of the product, line up the holes in the plastic tabs on the upper end of the net wit
Краткое содержание страницы № 7
ASSEMBL ASSEMBLY Y 1 2 Backboard 14 16 • Pull the rim down, as shown. 3 4 Upper Posts 17 • Wipe the backboard with a soft cloth. • Carefully peel a label from the label sheet and apply it to the backboard as shown. Smooth out the label to remove any air bubbles. • Repeat this procedure to apply the remaining labels to the backboard. Hint: These labels are designed to overlap! • Turn the backboard over. • Fit the upper posts onto the backboard. Rim Hint: The upper posts only assemble to the bac
Краткое содержание страницы № 8
ASSEMBL ASSEMBLY Y Post Latch Tab 19 21 • Flip down the post latch tabs. 20 • Lift the rim, as shown. 22 Plug Plug “T” End Base • Bend the “T” end of a plug and insert it into the hole in a base. • Repeat this procedure to assemble the other plug into the other base. Hint: You may need the help of another adult with this Note: After assembly is complete, fill each base with water or assembly step. approximately 50 lbs. (22.7 kg) of sand (water and sand not • Fit the ends of the upper posts int
Краткое содержание страницы № 9
A ADJUSTMENTS DJUSTMENTS IIMPORTANT! MPORTANT! Rim height should only be Rim height should only be a adjusted b djusted by y an adult. an adult. Mak Make e sure children are sure children are 2 n not standing belo ot standing below w the r the riim m when adjusting when adjusting the r the riim m height. height. 1 T Te ensioners nsioners • To adjust the tensioners on the back of the net, pull the free end of the strap to the desired tightness. U Unlatch nlatch L Latch atch • Secure the fas
Краткое содержание страницы № 10
5 SPOR 5 SPORTS IN ONE! TS IN ONE! IIMPORTANT! MPORTANT! Only use the balls and hoc Only use the balls and hock ke ey y stic stick k supplied with this to supplied with this toy y.. BASKETBALL FOOTBALL BASEBALL SOCCER HOCKEY 10 10
Краткое содержание страницы № 11
CARE AND MAINTENANCE CARE AND MAINTENANCE • This toy includes three inflatable balls. If a ball becomes soft, inflate it with a standard, manual air pump with a standard air needle. • The balls will contain the correct amount of air when the circumference measures: - Basketball: 19-20” (48-50 cm) - Soccer Ball: 17” (43 cm) - Football: 12” (30 cm) • Measure the circumference of each ball with a tape measure or a piece of string cut to the appropriate length. Do no over-inflate the balls. •
Краткое содержание страницы № 12
For countries outside the United States: CANADA Questions? 1-800-432-5437. Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2; www.service.mattel.com. GREAT BRITAIN: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303; www.service.mattel.com/uk. AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. NEW ZEALAND: 16-18 William Pickering Drive, Albany 133
