Краткое содержание страницы № 1
In-Ground Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Write Model Number
From Box Here:
REQUIRED TOOLS AND MATERIALS:
WARNING!
• 3 Capable Adults
• (2) Stepladders 8 ft. (2.4 m)
•
• Carpenter’s Level
• Safety Goggles
• Container to Mix
• 15’ Tape Measure
• (2 each) Wrenches and/or Socket Wrenches and
Sockets (Deep-Well Sockets are Recommended).
READ AND UNDERSTAND
• Shovel & Post Hole
OPERATOR'S MANUAL
3/8" 1/2" 9/16" 3/
Краткое содержание страницы № 2
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL SAFETY INSTRUCTIONS WARNING FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN Read and understand warnings listed SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. below before using this product. Owner must ensure that all players know and Failure to follow these warnings may follow these rules for safe operation of the system. result in serious injury and/or property damage. To ensure safety, do not att
Краткое содержание страницы № 3
1. Ensure ground is level with playing surface, then dig pole hole. PLAYING SURFACE WARNING! 24" (61 cm) 36" (91.4 cm) GROUND SURFACE CONTACT UTILITIES BEFORE DIGGING. 2. Install nut (2) to J-bolt (1) as 2 shown. Repeat procedure for 2-1/2” other three J-bolts (1). 3 (6.35 cm) 2 IMPORTANT! Make sure nuts are 2-1/2” (6.35cm) from top of J-Bolts. 1 2 NOTE: Make sure J-bolts (1) are in the illustrated position. 1 3. Install threaded ends of J-bolts (1) through holes in mounting plate (3) and sec
Краткое содержание страницы № 4
4. Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill. 5. Insert J-bolts (1) from mounting plate (3) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to level mounting plate on top of drainage hill. Level mounting plate and square with playing surface. Clean off any excess cement on mounting plate at this time. IMPORTANT! PLAYING SURFACE Front of mou
Краткое содержание страницы № 5
PLAYING SURFACE WARNING! THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN 5 SERIOUS INJURY AND/OR PROPERTY DAMAGE. 6. Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2). IMPORTANT! Holes in pole must be parallel with playing surface. PLAYING SURFACE 7. Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. NOTE: Position crank jack 5 mounting as show
Краткое содержание страницы № 6
8. Beginning with upper support arm (8) secure support WARNING! arms to pole. Continue by securing lower support arm (9) as shown. THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR IMPORTANT! PROPERTY DAMAGE. Do Not Over Tighten. 27 28 27 28 14 28 8 13 13 28 12 27 28 27 28 9 13 14 28 28 13 12 7 14 7 33 IMPORTANT! Bushing types are identified with a letter. 27 28 ID# M880961 02/06 6
Краткое содержание страницы № 7
Secure backboard to support arms (8 and 9) as 9. shown. IMPORTANT! Bushing types are identified with a letter. IMPORTANT! Do Not Over Tighten. 28 13 13 27 14 28 28 28 14 13 10 8 10 27 13 13 28 28 14 27 10 13 9 27 28 02/06 ID# M880961 7
Краткое содержание страницы № 8
10. Secure jack brackets (21) to to mounting bracket as shown. 14 13 13 11 21 21 REAR VIEW 20 11. NOTE: Position U-joint of crank jack (20) as shown. Where tubes on crank jack join, hold steady to keep both tubes from rotating. Rotate handle clockwise on crank jack to the fully extended position. IMPORTANT! Hold Here. ID# M880961 02/06 8 PLAYING SURFACE
Краткое содержание страницы № 9
12. A. Insert spacer (4) through spacer of screw jack as shown. WARNING! B. Install crank jack (20) U-joint to lower support arm (9) as shown. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY A. AND/OR PROPERTY DAMAGE. 4 20 20 9 IMPORTANT! Bushing types are B. identified with a letter. 28 28 14 9 27 28 12 28 13 28 13 REAR VIEW 20 IMPORTANT! Do Not Over Tighten. 02/06 ID# M880961 9 PLAYING SURFACE
Краткое содержание страницы № 10
13. Rotate jack handle until jack (20) aligns with jack brackets (21). Secure crank jack (20) to jack brackets (21) as shown. WARNING! TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 20 15 14 15 34 13 21 13 REAR VIEW NOTE: Some adjustment will be necessary to align the lower crank jack and bushings to jack brackets (21). ID# M880961 02/06 10 PLAYING SURFACE
Краткое содержание страницы № 11
7 7 8 8 10 9 87 10 9 87 10 9 87 10 98 7 9 9 1 1 0 0 14. Set-up For Leftt Side Set-up For Right Side Apply height indicator A. labels (18 and 19) to 16 16 height indicators (16). 10 9 8 7 10 10 9 9 7 8 8 7 10 9 8 7 10 7 8 9 18 10 7 9 10 19 8 9 8 7 10 7 8 9 B. Attach height indicators (16) to lower arm in areas as shown by turning screws (17) into place with a phillips IMPORTANT! screwdriver. Note Orientation of Height Indicators: 10’ Mark Should Face Away From Backboard. 10 7 9 8 10 7 8 9 10
Краткое содержание страницы № 12
15. Install net (30) to rim as shown. A. B. C. D. 30 30 Attach rim assembly (29). For rim assembly, see 16. instructions included with rim. 23 29 Rim Assembly 24 25 22 25 Remove rim cover prior to installing rim assembly to board. IMPORTANT! Refer To Instructions Carefully cut and peel Included With Rim protective film away from Hardware For Rim board prior to attaching rim. Assembly. ID# M880961 02/06 12
Краткое содержание страницы № 13
Check leveling at this time. Pole (5) should 17. be level in all directions. After system is leveled, completely tighten nuts (2) above pole flange. 5 NOTE: If adjustment is necessary, adjust system by rotating the nuts (2) between mounting plate (3) and pole flange. 2 18. Apply height adjustment label (31) to front of pole as shown. HR83008PoleGusset REGULATION RIM HEIGHT IS 31 10 FEET (3.05 m). 02/06 ID# M880961 13 10FT_HER.EPS
206239
Краткое содержание страницы № 14
32 Secure pole pad (32) as 19. shown. NOTE: Pole pad may NOT be included in this model. MHE19.EPS
206239 Height Adjustment 20. Rotate crank handle to raise or lower backboard. NOTE: If height adjustment is difficult to operate, you may have over tightened the areas indicated. M83013.EPS
211560 M83014.EPS
ID# M880961 02/06 14 211560
Краткое содержание страницы № 15
PARTS LIST Item Qty. Part No. Description 18 1 204739 Label, Height Indicator, Right 19 1 204740 Label, Height Indicator, Left 1 4 200573 J-Bolt, 1/2-13 x 24” Long 20 1 222880 Crank, Jack 2 12 265575 Nut, Hex, 5/8-11 21 2 908292 Bracket, Crank Jack Support 3 1 900661 Anchor Plate 22 4 203017 Nut, Hex, 3/8-16 4 1 220579 Spacer, 0.53 I.D. x 0.75 O.D. x 5” Long 23 2 205347 Bolt, Carriage, 3/8-16 x 3.5” Long 5 1 908310 Pole 24 2 200512 Bolt, Hex, Tap, 3/8-16 x 3.5” Long 6 8 200704 Washer, 5/8” x 1
Краткое содержание страницы № 16
HARDWARE IDENTIFIER (NUTS, WASHERS & STEEL SPACERS) Item #4 (1) spacer 1/2 x 5 Long Item #6 (8) Item #2 (12) Item #26 (4)* Item #13 (20) Item #14 (11) Item #7 (2) Item #25 (6) Item #22 (4) HARDWARE IDENTIFIER (PLASTIC & NYLON SPACERS) Item #15 (2) Item #28 (20) Item #27 (8) * You May Have Extra Parts With This Model. ID# M880961 02/06 16
