Краткое содержание страницы № 1
ML-79 WET WASH
Installation/Operator's Manual
WARNING: For your safety the
AVERTISSEMENT: Assurez-vous de bien
information in this manual must be
suivre les instructions données dans cette
followed to minimize the risk of fire or notice pour réduire au minimum le risque
explosion or to prevent property damage, d’incendie ou d’explosion ou pour éviter tout
personal injury or death.
dommage matériel, toute blessure ou la mort.
Do not store or use gasoline or other flammable
Ne pas entreposer
Краткое содержание страницы № 2
Retain This Manual In A Safe Place For Future Reference American Dryer Corporation products embody advanced concepts in engineering, design, and safety. If this product is properly maintained, it will provide many years of safe, efficient, and trouble-free operation. ONLY qualified technicians should service this equipment. OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation/operator's manual included with the dryer. The following “FOR YOUR SAFETY” caution
Краткое содержание страницы № 3
IMPORTANT YOU MUST DISCONNECT and LOCKOUT THE ELECTRIC SUPPLY and THE GAS SUPPLY BEFORE ANY COVERS or GUARDS ARE REMOVED FROM THE MA- CHINE TO ALLOW ACCESS FOR CLEANING, ADJUSTING, INSTALLATION, or TESTING OF ANY EQUIPMENT per OSHA (Occupational Safety and Health Administra- tion) STANDARDS. «Attention: Lor des opérations d’entretien des commandes étiqueter tous fils avant “Caution: Label all wires prior to de les déconnecter. Toute erreur de disconnection when servicing controls. Wiring câb
Краткое содержание страницы № 4
WARNING The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONAL INJURY or FIRE COULD RESULT. WARNING DRYER MUST NEVER BE OPERATED WITHOUT THE LINT FILTER/SCREEN IN PLACE...EVEN IF AN EXTERNAL LINT COLLECTION SYSTEM IS USED. IMPORTANT PLEASE OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment and/or specified in the installation/operator's manual included with the dryer. Dryers must not be installed or stored in an area where it will be
Краткое содержание страницы № 5
Table of Contents SECTION I ......................................................................................................... 3 IMPORTANT INFORMATION A. Receiving and Handling ............................................................................................................... 3 B. Safety Precautions ....................................................................................................................... 4 SECTION II ...........................................
Краткое содержание страницы № 6
SECTION VI ..................................................................................................... 32 ROUTINE MAINTENANCE A. Cleaning ................................................................................................................................... 32 SECTION VII ................................................................................................... 34 TROUBLESHOOTING SECTION VIII .....................................................................
Краткое содержание страницы № 7
SECTION I IMPORTANT INFORMATION A. RECEIVING and HANDLING The dryer is shipped in a protective stretch wrap cover with protective cardboard corners and top cover (or optional box) as a means of preventing damage in transit. Upon delivery, the dryer and/or packaging, and wooden skid should be visually inspected for shipping damage. If any damage whatsoever is noticed, inspect further before delivering carrier leaves. Dryers damaged in shipment: 1. ALL dryers should be inspected upon receipt a
Краткое содержание страницы № 8
B. SAFETY PRECAUTIONS WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury, or loss of life. WARNING: The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONAL INJURY or FIRE COULD RESULT. 1. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 2. Purchaser/user should cons
Краткое содержание страницы № 9
7. A program should be established for the inspection and cleaning of lint in the burner area, exhaust duct work, and area around the back of the dryer. The frequency of inspection and cleaning can best be determined from experience at each location. WARNING: The collection of lint in the burner area and exhaust duct work can create a potential fire hazard. 8. For personal safety, the dryer must be electrically grounded in accordance with local codes and/or the National Electrical Code ANSI/NF
Краткое содержание страницы № 10
SECTION II SPECIFICATIONS / COMPONENT IDENTIFICATION A. SPECIFICATIONS Basket Diameter 37" 94 cm Basket Depth 36" 152.4 cm Basket Motor 1 HP .746 kw Door Opening (Diameter) 31-3/8" 79.7 cm Basket Volume 22.4 cu. ft. .634 cu. m. Dryers per 20'/40' container 10/20 Dryers per 45'/48" Truck 24/24 Voltage Available 120-460v / 10-30 / 50/60 Hz Approx. Weight (Uncrated) 721 lbs. 327 kg Approx. Weight (Crated) 771 lbs. 349.7 kg Heat Input 200,000 btu/hr 50,400 kcal/hr Airflow 1,200 cfm 33.98 cmm Inlet
Краткое содержание страницы № 11
Specifications ML-79 WET WASH 7
Краткое содержание страницы № 12
B. COMPONENT IDENTIFICATION 1. Dryer Front View Illus. No. Description 1 Controls 2 Control (top access) Door Assembly 3 Main Door Assembly (Left hand shown) 4 Lint Compartment Area (lint screen located behind door) 5 Data Label and Installation Label (located behind control [service] door) 6 Emergency Stop 8
Краткое содержание страницы № 13
SECTION III INSTALLATION PROCEDURES Installation should be performed by competent technicians in accordance with local and state codes. In the absence of these codes, the installation must conform to applicable American national Standards: National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION, or in CANADA, the Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION. A. LOCATION REQUIREMENTS Before installing the dryer be sure the location controls to local codes and ordina
Краткое содержание страницы № 14
B. UNPACKING AND SETTING UP Remove protective shipping material (i.e., plastic wrap and optional shipping box) from dryer. IMPORTANT: Dryer must be transported and handled in an upright position at all time. The dryer can be moved to its final location with or without the skid attached. To un-skid the dryer, locate and remove the four (4) bolts securing the base of the dryer to the wooden skid. Two (2) are at the rear base (remove the back panel for access), and two (2) are located in the bott
Краткое содержание страницы № 15
C. DRYER ENCLOSURE REQUIREMENTS Bulkheads and partitions should be made of noncombustible materials and must be located a minimum of twelve (12) inches (18 inches or more is recommended for ease of installation, maintenance, and service) above the dryer outer top, except along the front of the dryer which may be partially closed in if desired. The clearance between the bulkhead header and the dryer must be a minimum of four (4) inches and must not extent more than four (4) inches to the rear o
Краткое содержание страницы № 16
IMPORTANT: Even though a minimum of only 12 inches is required, 18 inches or more is suggested, especially in cases where sprinkler heads are over the installation and service. IMPORTANT: When fire sprinkler systems are located above the dryers, a minium of 18 inches above the dryer console (module) is required. Dryers may be positioned side wall to side wall however, a 1/16” minimum allowance is required between dryers (or wall) for base of installation and maintenance. Allowances must be mad
Краткое содержание страницы № 17
To compensate for the use of registers or louvers used over the openings, this make-up air must be increased by approximately thirty-three percent (33%). Make-up air openings should not be located in an area directly near where exhaust vents exit the building. It is not necessary to have a separate make-up air opening for each dryer. Common make-up air openings are acceptable. However, they must be set up in such a manner that the make-up air is distributed equally to ALL of the dryers. EXAMP
Краткое содержание страницы № 18
E. EXHAUST REQUIREMENTS 1. General Exhaust Duct Work Information Exhaust duct work should be designed and installed by a qualified professional. Improperly sized duct work will create excessive back pressure which results in slow drying, increased use of energy, overheating of the dryer, and shutdown of the burner by the airflow (sail) switches, burner hi-limits, or basket (tumbler) hi-heat thermostats. CAUTION: Dryer must be exhausted to the outdoors. CAUTION: Improperly sized or installed ex
Краткое содержание страницы № 19
2. Single Dryer Venting Where possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust duct should be laid out in such a way that the duct work travels as directly as possible to the outdoors with as few turns as possible. It is suggested that the use of 90º turns in the ducting be avoided; use 30º or 45º angles instead. The shape of the exhaust duct work is not critical so long as the minimum cross section area is provided. IMPORTANT: Minimum duct size for dry
Краткое содержание страницы № 20
It is important that the duct work from each dryer not exceed fifteen (15) feet with no more than (2) elbows (excluding dryer connections and outside exhaust outlets). If the duct work exceeds fifteen (15) feet or has numerous elbows, the cross section area of the duct work must be increased in proportion to the length and number of elbows in it. In calculating duct size, the cross section area of a square or rectangular duct must be increased by twenty (20) percent for each additional fifteen
