Краткое содержание страницы № 1
Краткое содержание страницы № 2
CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FAN INSTALLATION . . . . . . . . . . . . . . . .
Краткое содержание страницы № 3
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mount- ing recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor. • Do not locate th
Краткое содержание страницы № 4
CAPISTRANO Casablanca PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. PERMA LOCK™ HARDWARE • LOCKING BOLT DOWNROD & BALL (MOTOR COUPLING) ASSEMBLY FAN PREPARATION IMPORTANT SAFETY INFORMATION! GROUND BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, WIRE MOTOR INSTALL THE THREADED DOW
Краткое содержание страницы № 5
CAPISTRANO Casablanca CROSSBAR MOUNTING BRACKET INSTALLATION CEILING FAN Proceed with installation as follows: APPROVED Step 1. Route the wires from the ceiling outlet box through OUTLET BOX the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture out- let box with the mounting hardware included with the outlet box. RIDGE Tighten the screws firmly by hand only, being careful not to CEILING SIDE bend the bracket by over tightening. WI
Краткое содержание страницы № 6
CAPISTRANO Casablanca HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and in- sert the ball into the canopy opening. Check that no wires were pinched. Ro- tate the fan body until the slot in the ball fits into the pin opposite the canopy opening. BALL Fan Hanging Weight CAPPED is 24 lbs BLUE D1-OPTION WIRE ON SLOT 3-SPEED ONLY PIN FOR INDEPENDENT Note: Independent control of the W-8 LIGHT light fixture using a W-8/W-811 re- CONTROL quires an additional indepe
Краткое содержание страницы № 7
CAPISTRANO Casablanca INSTALLING THE BLADE/BLADE HOLDER TO FAN MOTOR PREPARATION Step 8. To reach the blade holder mounting holes in the fan motor the dummy switch housing must be removed. 9 Take out the two 5-32 X /32” screws secur- ing the dummy switch housing and remove. Put the two (2) screws aside for the mo- ment, they will be used in Step 15 to install the switch housing after the blades are in- stalled. The dummy switch housing is used only when shipping the fan. Note: Save these two scr
Краткое содержание страницы № 8
CAPISTRANO Casablanca BLADE INSTALLATION Step 10. Attach each blade to a blade holder securing it with the four blade screws provided. Using the screwdriver, tighten securely BLADE SCREW by hand only. (4 PER BLADE) BLADE BLADE HOLDER REMOVE SHIPPING BLOCKS Step 11. On the flywheel remove the five SHIPPING shipping blocks by unscrewing the screws. BLOCKS Set these screws aside for installing the blades in Step 12. Discard the five shipping blocks. Note: Save these five screws, they will be used i
Краткое содержание страницы № 9
CAPISTRANO Casablanca COMPLETING INSTALLATION SWITCH HOUSING SWITCH HOUSING MOUNT SCREW AND (REMOVED IN STEP 8) CAP 9 5-32 X /32″ ASSEMBLY (2) PREPARATION SWITCH HOUSING Step 13. Locate the switch housing/cap SWITCH CONNECTOR 3 assembly and remove the two 8-32 X /8″ HOUSING (SOCKET) screws holding the cap onto the switch housing. REVERSE SWITCH Note: Save these two screws–they CAP will be used in Step 18! PULL CHAIN SWITCH CAP SCREW 3 8-32 X /8″ (2) CONNECTING THE SWITCH HOUSING ASSEMBLY Step 14
Краткое содержание страницы № 10
CAPISTRANO Casablanca INSTALLING THE SWITCH HOUSING ASSEMBLY Step 15. Line up the two inner clear- ance holes in the cap with the two threaded holes in the switch mounting plate standoffs. CAUTION! Before continuing to the next step check that a wire or com- ponent inside the switch housing will not be pinched as it is installed. 9 Step 16. Use the two (2) 5-32 X /32″ screws removed in Step 8 to install the switch housing assembly. Tighten securely by hand only. SWITCH HOUSING MOUNT SCREW 9 5-3
Краткое содержание страницы № 11
R 3-SPEED W-4/W-411 WALL CONTROL OF THE FAN • The W-4 allows the choice of four (4) different speed settings. • No light fixture is used. • Set the FAN pull chain switch to the HIGH speed setting. • No changes in household or fan wiring are required. • The fan may be turned ON and OFF by the W-4 wall control. CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty operation of the fan and damage to the W-4/W-411 wall control. To con- firm fan is set to HIGH: Turn W-4/ W-411 f
Краткое содержание страницы № 12
R 3-SPEED OPERATION Pull-chain switches on the fan control the fan and lights. FAN & SPEED Using the fan control pull-chain switch: Fan off at start. CONTROL First pull: fan ON, low speed PULL CHAIN SWITCH Second pull: medium speed Third pull: high speed Fourth pull: fan OFF Using the optional light pull-chain switch: Light off at start. First pull: light ON Second pull: light OFF Direction of blade rotation is controlled by the reverse slide REVERSE switch on the side of the switch housing.
Краткое содержание страницы № 13
TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth Never Lubricate this Fan! should be used to prevent scratching the finish. A vacuum cleaner The precision motor at the heart of your Casablanca fan features brush nozzle can remove heavier dust. Surface smudges or an accu- sealed bearings that are lubricated for life. Do not attempt to oil mulation of
Краткое содержание страницы № 14
761 C O R P O RAT E C EN T E R D RI VE • P OM ON A , C A 91768 • 800- 759- F A N S ( 3267) ©C OP Y R IG H T 1998 C AS AB L A N C A F AN C OM P A N Y • U . S . P AT E N T P EN D I N G P RI N T E D IN RO C 14
