Краткое содержание страницы № 1
PARTS AND SERVICE MANUAL
FOR
DIMPLEX 23” OUTDOOR
ELECTRIC FIREPLACE
Model DFO2307
Краткое содержание страницы № 2
TABLE OF CONTENTS OPERATION PAGE 2 PARTS DRAWING PAGE 3 PARTS LIST PAGE 4 WIRING DIAGRAM PAGE 5 FRONT GLASS REMOVAL PAGE 6 UPPER LIGHT REPLACEMENT PAGE 7 LOWER LIGHT REPLACEMENT PAGE 8 MAIN ON/OFF REPLACEMENT PAGE 9 FLAME ROD AND MOTOR REPLACEMENT PAGE 10 CIRCUIT BOARD REPLACEMENT PAGE 11 1
Краткое содержание страницы № 3
DFO2307 OPERATION ELECTRIC FIREPLACE MANUAL CONTROL The manual controls for the firebox are located in the upper right hand corner behind the access panel. To access the controls, open the upper access panel by pulling forward and down. To locate controls refer to Figure 3. A. Main On/Off Switch The ON/OFF SWITCH supplies power to the flames and over head lights. NOTE: This unit does not have a heat option. Main On/O
Краткое содержание страницы № 4
5 4 2 6 10 3 7 1 9 8 11 3
Краткое содержание страницы № 5
DFO2307 REPLACEMENT PARTS FIREBOX, 23” – Dimplex CATALOGUE NO. DFO2307 PART NO. 6903100100 REPLACEMENT PART 1. MOTOR, ASSEMBLY 3000240200 2. LED LIGHT, 1 WATT 3700060100 3. ON/OFF SWITCH 2800150100 4. CIRCUIT BOARD 3000520100 5. MIRROR 5900750100 6. GLASS FRONT 5900710100 7. LED LIGHT, BOTTOM 3700060200 8. TRANSFORMER 2100200100 9. FLAME ROD 5900780100 10. BUSHING 8500000400 11. LOGSET 0478270100
Краткое содержание страницы № 6
WIRING DIAGRAM 5 THIS END TO BE CONNECTED TO MAIN PCB BOARD TRANSFORMER. REFER TO TABLE (BACKSIDEVIEW) FOR P/N. CONNECTOR, WIRE TWISTER CONNECTOR, FEMALE (HARNESS INCLUDED) SQUARE SOLDER PAD "B" TERMINAL TYP. "A" TERMINAL LIGHT WIRE HARNESS YELLOW WIRE OF CABLE TO LINE UP WITH SQUARE SOLDER PAD OF CONNECTOR ON BOARD. "A" TERMINAL 1 WATT LED TOP LIGHT MAIN ON/OFF SWITCH INCLUDED IN LIGHT WIRE HAR
Краткое содержание страницы № 7
DFO2307 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. FRONT GLASS REMOVAL 1. Remove top from mantel. 2. Lift firebox out of mantel. 3. Lay firebox on it’s back. 4. Remove screws from the left and right side of the front glass lower support. 5. Insert the tip of a slot screwdriver between the glass edge on either the left or right side trim. 6. Using the screwdriver as a lever, apply pressure in a downw
Краткое содержание страницы № 8
DFO2307 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. It is a good idea to replace all of the lights at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace the lights. UPPER LIGHT REPLACEMENT 1. Remove the front glass as shown on page 6 of this manual. 2. Remove the top trim piece by removing the 3 retaining sc
Краткое содержание страницы № 9
DFO2307 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Lights need to be replaced when you notice a dark section of the flame. There are three lights under the log set which generate the flames and embers located under the emberbed. It is a good idea to replace all of the lights at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open t
Краткое содержание страницы № 10
DFO2307 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. MAIN ON/OFF SWITCH REPLACEMENT 1. Remove the front glass as shown on page 6 of this manual. 2. Remove the top trim piece by removing the 3 retaining screws. 3. Remove the 10 retaining screws and lift the top off of the unit. 4. Locate the main on/off switch mounted on the top panel and disconnect the wiring clips and connections noting their original lo
Краткое содержание страницы № 11
DFO2307 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. FLAME ROD AND MOTOR REPLACEMENT 1. Remove the front glass as shown on page 6 of this manual. 2. Remove the top trim piece by removing the 3 retaining screws. 3. Remove the 10 retaining screws and lift
Краткое содержание страницы № 12
DFO2307 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE CIRCUIT BOARD 1. Remove the front glass as shown on page 6 of this manual. 2. Remove the top trim piece by removing the 3 retaining screws. 3. Remove the 10 retaining screws and lift the
